Starting And Stopping; Assembly Instructions - Flymo Minimo Original Instructions Manual

CABLES - IMPORTANT
•
Use only 1.00mm 2
length maximum.
Maximum rating :
1.00mm size cable, 10 amps 250 volts AC.
2
THE MINIMO IS SUPPLIED WITH AN ELECTRIC MAINS
CABLE WIRED DIRECTL Y INTO THE PRODUCT .
1. Flymo Mains Cables and Extension Cables are available
from your local Approved Service Centre.
2. Do not wire an extension cable directly to your product
yourself. Please contact your local Approved Service
Centre for further information on the connectors and
kits available.
3. Only use extension cables specifically designed for
outdoor use.
CONNECTORS - IMPORTANT
•
Flymo connectors are suitable for use with 2 core
cable only. Under no circumstances should these
connectors be used for earthed products.
•
All Flymo connectors and cables are of splashproof con-
struction. They are not waterproof and must not be left
outside permanently nor should they be submerged or
immersed in water. Do not let cable lay or trail through
pools of water or splashed with water from hose pipes.
MAINS PLUG REPLACEMENT - IMPORTANT
• If the plug supplied is cut off it should be
destroyed. There is an electric shock hazard if
a cut off plug is inserted into a 13 amp socket.
A
handle
bolt
handle
tube
B
nut
wing knob
C
hinge
fixing pin
D
Lock-off button
size cable up to 40 metres

Assembly Instructions

wing knob
nut
handle
tube
pegs
motor cover
bracket

Starting and Stopping

Switch lever
1. No earth required. Flymo products are double insulated
to EN60335 and under no circumstances should an
earth be connected to any part of the product.
2. Ensure the mains voltage suits your product.
3. IMPORTANT!
The wires in the mains lead are coloured in accor-
dance with the following code:
BLUE
BROWN
The wire which is coloured BLUE must be connect-
ed to the Terminal which is marked with the letter
'N' or coloured BLACK.
The wire which is coloured BROWN must be con-
nected to the Terminal which is marked with the let-
ter 'L' or coloured RED.
4. It is important that the outer sheath is clamped cor-
rectly into the 3-pin plug.
5. If in doubt consult your local Service Repairer or
qualified electrician before the machine is used.
6. A 13 Amp fuse must be fitted to the Mains Plug.
7. The normal plug fuse and household fuse only pro-
tect the electrical equipment and are not a safe-
guard against electrocution.
If your product is hard wired i.e. non-detachable
mains electric cable, a conversion kit and extension
cable is available from all Approved Service Centres
which can be found in your local Yellow Pages.
Assembly of handle to handle tube (A)
1. Insert the handle tube into the handle as illus-
trated, ensuring the handle is in an upright posi-
tion
2. Insert the nut into the wing knob.
3. Secure with the bolt and wing knob.
Assembly of handle tube to motor cover (B)
1. Locate the the handle tube onto the two pegs in
the neck of the motor cover.
2. Insert the bolt through the motor cover and the
centre hole of the handle tube.
3. Insert the nut into the wing knob.
4. Secure with the wing knob.
bolt
Assembly of motor cover to hood (C)
• Note:- Ensure the handle is to the rear of the
hood when the motor cover is fitted.
1. Align the hole in the hinge of the motor cover
with the holes in the bracket on the hood.
Secure by inserting the fixing pin and pressing
firmly until a click is heard.
2. Repeat on the other side.
3. Secure the motor cable to the handle tube with
the cable clips provided.
Starting
1. Hold as illustrated in Fig D.
2. To start, press the lock-off button down, whilst
pressing the lock-off button, squeeze the switch
lever.
Stopping
1. To stop your product, release the switch lever.
- NEUTRAL
- LIVE