1. Manuals
  2. Brands
  3. Invacare Manuals
  4. Wheelchair
  5. Typhoon II
  6. User manual

Invacare Typhoon II User Manual

Invacare typhoon ii power wheelchair user manual
Hide thumbs Also See for Typhoon II:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Service Manual, Operating Manual
Yes, you can.
®
Invacare® Typhoon II
Power wheelchair
User manual

Advertisement

Table of Contents
loading

Related Manuals for Invacare Typhoon II

Summary of Contents for Invacare Typhoon II

  • Page 1 Yes, you can. ® Invacare® Typhoon II Power wheelchair User manual...
  • Page 3 How can you get in touch with Invacare®? If you have any questions or need support, please contact your authorised Invacare® Dealer, who has the necessary know-how and equipment plus the special knowledge concerning your Invacare® product, and can offer you all-round satisfactory service. Should you wish to contact Invacare® directly, you can reach us in Europe at the following addresses and phone numbers.
  • Page 4 +44 (0)1656 77 62 20 Pencoed uk@invacare.com Bridgend CF35 5AQ WWW: www.invacare.co.uk United Kingdom Invacare Mecc San s.r.l. +39 0445 38 00 59 Via dei Pini, 62 Fax: +39 0445 38 00 34 I - 36016 Thiene (VI) italia@invacare.com ITALIA WWW: www.invacare.it...
  • Page 5 +46 (0)8 761 81 08 Fagerstagatan 9 sweden@invacare.com S-163 91 Spånga finland@invacare.com Sverige WWW: www.invacare.se Tillverkare: MÖLNDAL Invacare® Deutschland GmbH  : +46 (0)31 86 36 00 Kleiststraße 49 Fax: +46 (0)31 86 36 06 D-32457 Porta Westfalica ginvacare@invacare.com Deutschland LANDSKRONA ...

  • Page 6: Table Of Contents

    Table of Contents Chapter Page Introduction Important symbols in this manual ..................13 Important symbols found on the vehicle ................15 1.2.1 Explanation of symbols on lifter warning sticker............17 Type classification and permissible use................18 Indications..........................18 Usability............................19 Warranty ...........................20 Life expectancy........................20 Safety notes General safety notes .......................21 Safety information with regard to care and maintenance ...........24 Safety information on electromagnetic interference ............25...
  • Page 7 Before driving for the first time....................36 Parking and stationary......................37 Taking Obstacles........................37 5.3.1 The ”SureStep“ System ....................37 5.3.2 Maximum obstacle height .....................37 5.3.3 Safety information when ascending obstacles .............38 5.3.4 The correct way to overcome obstacles ...............39 Driving up and down gradients....................40 Use on public roads ........................40 Pushing the wheelchair in freewheel mode Electrically disengaging gearless motors ................41...
  • Page 8 8.4.2 Adjusting the postural belt correctly................58 The Lifter ..........................59 Adjusting and removing the tray ...................60 8.6.1 Laterally adjusting the tray....................60 8.6.2 Adjusting the depth of the tray / removing the tray............61 8.6.3 Swinging the tray away to the side ................61 Child seat (option) ........................62 8.7.1 The headrest of the child seat ..................62...
  • Page 9 Laterally mounted legrests.....................87 9.2.1 Standard footrest with pre-set angle................87 9.2.1.1 Swivelling the footrest outward and/or removing.............87 9.2.1.2 Setting the angle......................88 9.2.1.3 Setting the end stop of the footrest .................90 9.2.1.4 Adjusting the length of the footrest................93 9.2.2 Manually height adjustable legrest 90° - 0° ..............94 9.2.2.1 Swivelling the legrest outward and/or removing............94 9.2.2.2...
  • Page 10 9.2.4.6 Unlocking and swivelling the calf plate backward when alighting ......122 9.2.4.7 Adjusting the angle adjustable foot plate...............123 9.2.4.8 Adjusting the angle and depth adjustable foot plate ..........124 10 Electrical system 10.1 Electronics protection system .....................125 10.1.1 The main fuse ......................126 10.2 Batteries ..........................127 10.2.1 Charging the batteries ....................127...
  • Page 11 13.2 Use of the wheelchair as a seat in a vehicle...............153 13.2.1 How the wheelchair is anchored in a vehicle for use as a vehicle seat .....156 13.2.2 How the user is secured within the wheelchair............157 13.3 Securing the wheelchair for transport without passengers ..........161 14 Refurbishment 15 Disposal 16 Technical specifications...

  • Page 12: Introduction

    The decision whether the model is suitable for the user may only be taken by medical specialists with appropriate expertise. Invacare® or their statutory representatives can accept no liability in cases in which the wheelchair has not been adapted to suit the users’ handicaps.

  • Page 13: Important Symbols In This Manual

    This manual contains copyrighted information. This manual may not be reproduced or reprinted either partly or completely without previous written consent from Invacare® or its statutory representatives. We reserve the right to make any necessary alterations on the grounds of technical improvements.
  • Page 14 RISK OF CRUSHING! This symbol warns of a risk of crushing caused by being careless with heavy components. • Always follow the instructions to avoid injury to the user or damage to the product. Wear eye protection This symbol refers to the requirement for wearing eye protection, for example when working with batteries.

  • Page 15: Important Symbols Found On The Vehicle

    Important symbols found on the vehicle This product has been supplied from an environmentally aware manufacturer. This product may contain substances that could be harmful to the environment if disposed of in places (landfills) that are not appropriate according to legislation. •...
  • Page 16 This wheelchair may be used as a vehicle seat, but only if it is equipped with a headrest that has been approved by Invacare for this purpose! • Please always make sure that the wheelchair is equipped with a headrest approved by Invacare before using it as a vehicle seat!

  • Page 17: Explanation Of Symbols On Lifter Warning Sticker

    If the power wheelchair is fitted with a table, it is imperative that it is removed and safely stowed when transporting the wheelchair in a vehicle! 1.2.1 Explanation of symbols on lifter warning sticker Do not lean out Do not drive up Do not allow any Never drive with Never drive over...

  • Page 18: Type Classification And Permissible Use

    Type classification and permissible use This vehicle was designed for persons whose ability to walk is impaired, but who are still in terms of their eyesight and physically and mentally able to operate an electric vehicle. It has been classified according to EN 12184 as a class B mobility product (for indoor and outdoor areas).

  • Page 19: Usability

    • You should immediately stop using your power wheelchair if its usability is restricted due to: - brake failure • You should immediately contact an authorised Invacare® dealer if the usability of your power wheelchair is restricted due to: - the lighting system failing or being defective...

  • Page 20: Warranty

    - unusual sounds developing or occurring Or if you have the feeling that something is wrong with your wheelchair. Warranty The terms and conditions of the warranty are part of the general terms and conditions particular to the individual countries in which this product is sold. Life expectancy We estimate a life expectancy of five years for this product, provided it is used in strict accordance with the intended use as set out in this document and all maintenance and service requirements...

  • Page 21: Safety Notes

    Safety notes READ WELL BEFORE OPERATION! General safety notes Danger of injury if mobility device is used in any other way than the purpose described in this manual! • Only ever use the mobility device in accordance with the instructions in this User's Manual (see chapter "Type classification and permissible use"...
  • Page 22 Danger of injury if the mobility device is switched off while driving, for example by pressing the On/Off Button or disconnecting a cable, due to it coming to an abrupt, sharp stop! • If you have to brake in an emergency, simply release the joystick which will bring you to a halt. (refer to the joystick operating manual for more information).
  • Page 23 Danger of fire or breaking down due to electric devices being connected! • Do not connect any electric devices to your mobility device that are not expressly certified by Invacare® for this purpose. Have all electrical installations done by your authorised Invacare® Dealer.

  • Page 24: Safety Information With Regard To Care And Maintenance

    Safety information with regard to care and maintenance Danger of accident and loss of guarantee if maintenance is insufficient! • For reasons of safety and in order to avoid accidents which result from unnoticed wear, it is important that this electric mobility product undergoes an inspection once every year under normal operating conditions (see inspection plan contained in service instructions).

  • Page 25: Safety Information On Electromagnetic Interference

    Safety information on electromagnetic interference This electric vehicle was successfully tested in accordance with International standards as to its compliance with Electromagnetic Interference (EMI) regulations. However, electromagnetic fields, such as those generated by radio and television transmitters, and cellular phones can influence the functions of electric vehicles.

  • Page 26: Safety Information On Driving And Freewheel Mode

    Safety information on driving and freewheel mode Danger of injury if the wheelchair tips over! • Inclines and declines can only be travelled up to the maximum safe slope (see chapter "Technical specifications" from page 164). • Always return the backrest of your seat or the seat tilt to an upright position before ascending slopes.
  • Page 27 Danger of breaking down in adverse weather conditions, i.e. extreme cold, in an isolated area! • If you are a user with severely limited mobility, we advise that in the case of adverse weather conditions DO NOT attempt a journey without an accompanying attendant! Danger of injury if your foot slides off the footrest and gets caught underneath the wheelchair when it is in motion! •...

  • Page 28: Safety Information Regarding Changes And Modifications To The Mobility Device

    EEC / MPG (Medical Devices Act) and only applies to the complete product. The CE marking is invalidated if components or accessories are replaced or added that have not been approved for this product by Invacare. In this case, the company that adds or replaces the components or accessories is responsible for the conformity assessment/ CE marking or for registering the wheelchair as a special design and for the relevant documentation.
  • Page 29 • Only use seating systems that have been approved by Invacare® for this power wheelchair. Electrical and electronic components which have not been approved by Invacare® for use with this mobility aid can cause fire hazards and lead to electromagnetic damage! •...

  • Page 30: Safety Information On Wheelchairs With A Lifter

    Safety information on wheelchairs with a lifter WARNING! Danger of injury by moving parts! • Never let objects get caught in the space underneath a raised lifter! • Make sure that neither you nor anyone else is injured by placing hands, feet other body extremities under the raised seat! •...
  • Page 31 WARNING: Danger of injuries and damage to the wheelchair can result if the wheelchair is lifted up or carried by the seat! The lifter motor can slip out of its fixation under the seat!! • Never attempt to lift the wheelchair by the seat, only by its frame!

  • Page 32: Key Features

    Key features 1) Button for disengaging drive (on push handle) 2) Armrest 3) Lever for disengaging a motor (only visible on right-hand side of picture) 4) Drive wheel 5) Remote 6) Legrests...

  • Page 33: Getting In And Out Of The Wheelchair

    Getting in and out of the wheelchair Important information when side transferring in and out of the wheelchair In order to side transfer it is necessary for the armrest to either be raised or removed completely depending on the model. A skirtguard can be installed as an option in connection with the parallel sliding armrest.

  • Page 34: Raise The Parallel Sliding Armrest / Remove The Skirtguard (Optional)

    Raise the parallel sliding armrest / remove the skirtguard (optional) Swivelling the armrest up • Swivel the armrest up to access from the side. Remove the clothes guard (option) for access • Disengage the release handle (1). • Pull the skirt guard out of the holder.
  • Page 35 Getting into the wheelchair: • Position your wheelchair as close as possible to your seat. This might have to be done by an attendant. • Switch your wheelchair off. • Apply the manual wheel lock of your wheelchair (if existing). •...

  • Page 36: Driving

    Driving NOTE The maximum load capacity that is stated in the technical data only states that the system is designed for this mass in total. However, this does not mean that one can sit a person with this body weight in the wheelchair without restrictions. Attention must be paid to the body proportions, such as height, weight distribution, abdominal girth, leg and calf girth and seat depth.

  • Page 37: Parking And Stationary

    • The rear mirror (if installed) is adjusted so you can look behind at all times without having to bend forward or shift your seating position. The gearless wheelchair has very dynamic performance! Please observe that gearless motors have very high performance! For this reason a wheelchair with a gearless drive has greater dynamic performance than wheelchairs fitted with conventional motors.

  • Page 38: Safety Information When Ascending Obstacles

    5.3.3 Safety information when ascending obstacles CAUTION: Danger of Tipping Over! • Never approach obstacles at an angle but at 90 degrees as shown below. • Put your backrest into an upright position before climbing an obstacle. ATTENTION: Risk of falling out of the chair and damage to the power wheelchair such as broken castors! •...

  • Page 39: The Correct Way To Overcome Obstacles

    5.3.4 The correct way to overcome obstacles Ascending Right • Approach the obstacle or the kerb slowly, head-on and at a right angle. • Depending on the wheel drive type, stop in one of the following positions: - In the case of centrally driven wheelchairs: 5 - 10 cm before the obstacle. - For all other drives: approx.

  • Page 40: Driving Up And Down Gradients

    Driving up and down gradients For information concerning the maximum safe slope, please see chapter "Technical specifications" starting on page 164. WARNING: Danger of tipping over! • Only ever drive downhill at a maximum of 2/3 of the top speed. Avoid sudden changes of direction or abrupt braking when driving on slopes.

  • Page 41: Pushing The Wheelchair In Freewheel Mode

    Please contact your Invacare ® dealer if you have any questions. Pushing the wheelchair in freewheel mode The motors of the wheelchair are equipped with automatic brakes, preventing that the wheelchair starts rolling out of control when the joystick box is switched off. When pushing the wheelchair manually whilst freewheeling, the magnetic brakes must be disengaged.

  • Page 42: Manually Disengaging Gearless Motors (Emergency Disengaging)

    Disengaging motors: • Press key (1). A peep tone will sound for about one second. The motors remain disengaged until a key is pressed (if you cannot hear the peep tone, or the peep tone stops after around one second, there is an error.
  • Page 43 NOTE: The motors may only be disengaged by an attendant, not by the user! This ensures that the motors are only disengaged if an attendant is available to secure the wheelchair and prevent unintended rolling. The levers for disengaging the motors are located behind the drive wheels. Disengaging motors: •...

  • Page 44: Remotes

    Remotes Your wheelchair may be equipped with one of several different remotes. For information on the different functions and how to operate a particular remote, please see its corresponding User Manual (enclosed).

  • Page 45: Adjusting The Wheelchair To The User's Seating Posture

    Adjusting the wheelchair to the user's seating posture WARNING: Danger of damage to the wheelchair and of accidents! With some combinations of adjustment options, collisions can occur between the legrest and the chassis or between the foot plates and the ground!This occurs in particular on wheelchairs with a lifter! •...

  • Page 46: Setting The Height Of The Remote

    8.1.2 Setting the height of the remote • Loosen one or both of the wing screws (1 and 2) that allow height adjustment of the joystick box. • Adjust the joystick box to the desired height. • Re-tighten the screw(s).

  • Page 47: Setting The Height Of The Armrests

    8.1.3 Setting the height of the armrests • Loosen the bolt (1). • Set the armrest at the desired height. • Retighten the bolt.

  • Page 48: Setting The Height Of The Parallel Sliding Armrests

    8.1.4 Setting the height of the parallel sliding armrests Requirements: • Allen key 2 mm • Loosen the screws (1) with the 2 mm Allen key on both sides of the spindle. • Turn the spindle clockwise (A). The armrest is raised.

  • Page 49: Adjusting The Angle Of The Armpad On The Parallel Sliding Armrests

    8.1.5 Adjusting the angle of the armpad on the parallel sliding armrests Requirements: • Allen key 4 mm • Open-end spanner 10 mm • Loosen the screw (1, on the inner side of the armrest), which allows adjustment of the angle of the armpad, while countering the nut (2, outer side of the armrest) with the...

  • Page 50: Adjusting The Width Of The Armrests

    8.1.6 Adjusting the width of the armrests The distance between the side sections can be adjusted by 5.5 cm on both sides (11 cm in total). Requirements: • Allen key 8 mm Where to find the adjustment screws The figure below shows the position of the screws (1) which allow armrest width adjustment (only the left side is shown in the illustration).
  • Page 51 Doing the adjustment • Loosen screw (1) • Adjust armrest to required position. • Retighten the screw. • Repeat this procedure for the second armrest.

  • Page 52: Manually Adjusting The Seat Tilt

    Manually adjusting the seat tilt The seat angle is adjusted by means of a spindle, which is to be found at the front underneath the seat frame. When adjusting the seat angle it should be ensured that at least 1cm of the threaded bolt always remains inside the spindle and is not completely unscrewed from the spindle.
  • Page 53 • Loosen the counter nut (1) of spindle. • Adjust the seat angle by turning the spindle (2). • Re-tighten the counter nut...

  • Page 54: Manually Adjusting The Backrest

    Manually adjusting the backrest 8.3.1 Adjusting the backrest using the gas pressure spring The lever for adjusting the backrest is located on the opposite side from the Joystick Box under the armrest. Adjusting angle of the backrest • Pull lever (1) upward. •...

  • Page 55: Adjust The Backrest Using The Perforated Plate

    8.3.1.1 Adjust the backrest using the perforated plate The angle of the backrest has six positions, from -10° to +30°. • Unscrew the hand screws (1) on both sides. • The backrest is adjusted by choosing a combination of one of the two bore holes in the backrest frame and one of the six bore holes in the fixing plate.

  • Page 56: Flex And Contour Seats

    8.3.2 Flex and Contour seats • Set the angle by turning the hand wheel (1).

  • Page 57: Postural Belts

    Postural belts A postural belt is an option which can either be fixed to the wheelchair ex-works or can be retrofitted by your specialist dealer. If your wheelchair is fitted with a postural belt, your specialist dealer will have informed you about fitting and usage. The postural belt is used to help the wheelchair user keep an optimum sitting position.

  • Page 58: Adjusting The Postural Belt Correctly

    If the belt is only fastened with a bolted connection, ensure that the connection has not loosened or undone. You can find more information about maintenance work on belts in the service manual, which is available from Invacare®.

  • Page 59: The Lifter

    Fehler! Textmarke nicht definiert.. Information regarding operation of the lifter at temperatures of less than 0 °C Invacare® mobility aids are fitted with safety mechanisms that prevent capacity overload of the electronic components. At operating temperatures below freezing point this can, in particular, lead to the lifter actuator being shut down after approx.

  • Page 60: Adjusting And Removing The Tray

    Adjusting and removing the tray CAUTION: Injury hazard or material damage if a power wheelchair which is fitted with a table is transported in a vehicle! • If a table is fitted, always remove it before transporting the wheelchair. 8.6.1 Laterally adjusting the tray •...

  • Page 61: Adjusting The Depth Of The Tray / Removing The Tray

    8.6.2 Adjusting the depth of the tray / removing the tray • Loosen the wing-screw (1). • Adjust the table to the desired depth (or remove it entirely). • Re-tighten the screw. 8.6.3 Swinging the tray away to the side CAUTION! Risk of injury! When the tray is raised it does not lock in place in this position! •...

  • Page 62: Child Seat (Option)

    Child seat (option) The child seat consists of the actual seat, a headrest and a laterally-mounted footrest. The following describes how these options can be adapted to the sitting posture of the user. 8.7.1 The headrest of the child seat 8.7.1.1 Adjusting the angle / depth of the headrest •...

  • Page 63: Adjusting The Height Of The Headrest

    8.7.1.2 Adjusting the height of the headrest • Loosen the clamping screw (1). • Move the headrest to the desired height. • Tighten the clamping screw.

  • Page 64: The Armrests / Setting The Angle

    8.7.2 The armrests / setting the angle Pre-requisites: • 13 mm open-ended spanner The adjusting screw for adjusting the angle of the armrest is to be found at the rear end of the armrest (A). • Loosen the counternut (1) using the open-ended spanner.

  • Page 65: The Backrest

    8.7.3 The backrest 8.7.3.1 Adjusting the height of the sliding handles (option) • Loosen the hand wheel (1 or 2). • Move the sliding handle to the desired position. • Tighten the hand wheel.

  • Page 66: Adjusting The Angle Of The Backrest Electrically

    8.7.3.2 Adjusting the angle of the backrest electrically As an option the backrest can be adjusted via an electric actuator. Please see chapter "Fehler! Verweisquelle konnte nicht gefunden werden." on page Fehler! Textmarke nicht definiert.. 8.7.3.3 Adjusting the angle of the backrest manually •...

  • Page 67: The Legrest Of The Child Seat

    8.7.4 The legrest of the child seat 8.7.4.1 Setting the angle of the footrest Pre-requisites: • 5 mm Allen key • Loosen the Allen screws at both ends of the footrest (1) (only one side is shown in the illustration). •...

  • Page 68: Swivelling The Footrest Upward / Removing The Legrest

    8.7.4.2 Swivelling the footrest upward / removing the legrest In order to simplify getting into the vehicle and alighting, the footrest can be swivelled upward. The footrest must also be swivelled upward so that the width of the legrest can be adjusted or the legrest dismantled.
  • Page 69 • Press the release button (1) and swivel the legrest outward. • Remove the legrest in an upward direction.

  • Page 70: Adjusting The Width Of The Legrest

    8.7.4.3 Adjusting the width of the legrest Pre-requisites: • Flat screwdriver • 5 mm Allen key • 3 mm Allen key • 13 mm open-ended spanner • Swivel the footrest upward and dismantle the legrest (see section "Swivelling the footrest upward / "...
  • Page 71 • Remove the plastic studs carefully using a flat screwdriver. • Remove the rubber mat.
  • Page 72 • Remove the screws (1) using the 3 mm Allen key. • Adjust the footrest bracket (2) to the desired width. • Re-position and tighten the screws.
  • Page 73 • If the width of the footrest has been altered, the width of the legrest brackets (1) on the wheelchair frame must be adapted appropriately. • Loosen the four screws (2) using the 13 mm open- ended spanner.
  • Page 74 • Swivel the footrest slightly upward so that the legrest halves can be turned inward without colliding. • Hang the legrest halves on the left and right and turn inward until the locking mechanisms on both sides lock in place. •...
  • Page 75 • Tighten the screw (1). • Re-close the belt with the Velcro® fastener (2) .

  • Page 76: Adjusting The Length Of The Legrest

    8.7.4.4 Adjusting the length of the legrest Pre-requisites: • 5 mm Allen key • Loosen the screw (1). • Adjust the lower leg length. • Tighten the screw.

  • Page 77: Adjusting The Angle Of The Legrest

    8.7.4.5 Adjusting the angle of the legrest Pre-requisites: • 6 mm Allen key • Metal pin 3 mm ∅, approx. 10 cm long • Hammer • Loosen the screw (1). • Insert the metal pin into the hole (2) and knock lightly with the hammer in order to loosen the halves of the plastic jacket.
  • Page 78 • Loosen the screw (1). • Insert the metal pin into the hole (2) and knock lightly with the hammer in order to loosen the halves of the plastic jacket. • Adjust the angle. • Tighten the screw. • Loosen the screw (1). •...

  • Page 79: Adjusting Footrests And Legrests

    Adjusting footrests and legrests Centre-mounted legrests 9.1.1 Electric legrest The electric legrest is operated via the remote. Please see chapter "Fehler! Verweisquelle konnte nicht gefunden werden." on page Fehler! Textmarke nicht definiert.. The electric legrest can be lowered completely to assist getting out of the wheelchair. To do so, move your seat into the correct position by lowering the lifter or by means of a negative seat angle (tilted slightly to the front).

  • Page 80: Lowering The Electric Legrest Completely To Assist Getting Out Of The Wheelchair

    9.1.1.1 Lowering the electric legrest completely to assist getting out of the wheelchair Warning! Misuse may destroy the legrest. • Please read and carefully follow the instructions below. Getting in/out of the wheelchair • Set the lifter and tilt to a comfortable position. •...
  • Page 81 Lifting up the footplates • You are sitting in the wheelchair. • Put your feet beside the footplates. • Pull the lever (1). The footplates rise up automatically. • Let go the lever (1) and put your feet on the footplates.
  • Page 82 Warning! Danger of damage to the legrest! • Always make sure that the footplates are fully raised to the uppermost position before adjusting the angle of the legrest! • Disregarding this advice will cause damage to your legrest. Adjusting the legrest •...

  • Page 83: Adjustable Legrest

    9.1.2 Adjustable legrest 9.1.2.1 Adjusting the angle Prerequisites: • 1x 10 mm open-ended spanner • Use the open-ended spanner to loosen the counternut (1). • Move the legrest to the desired position by turning the spindle (2). • Tighten the counternut.

  • Page 84: Adjusting The Length Of The Legrest

    9.1.2.2 Adjusting the length of the legrest Prerequisites: • 1x 5 mm socket head spanner • Use the socket head spanner to loosen the fastening screws (1). • Slide the foot support to the desired height. • Tighten the fastening screws.

  • Page 85: Adjusting The Calf Plate To The Calf Width Of The User

    9.1.2.3 Adjusting the calf plate to the calf width of the user The calf plate of the legrest can be adapted to the user’s calf width by bending apart or together. • Bending the calf plate to the desired width.

  • Page 86: Adjusting The Angle Of The Foot Plate

    9.1.2.4 Adjusting the angle of the foot plate Prerequisites: • 1x 5 mm socket head spanner • Fold up the foot plates in order to access the adjusting screws. • Use the socket head spanner to adjust the adjusting screws (1). •...

  • Page 87: Laterally Mounted Legrests

    Laterally mounted legrests 9.2.1 Standard footrest with pre-set angle 9.2.1.1 Swivelling the footrest outward and/or removing The small unlocking button is located on the upper section of the footrest. When the footrest is unlocked, it can be swivelled inward or outward when getting into the wheelchair as well as being removed completely.

  • Page 88: Setting The Angle

    9.2.1.2 Setting the angle PLEASE NOTE: Danger of injury due to incorrect adjustment of the footrests and legrests. • Before and during every journey it is imperative to ensure that the legrests contact neither the castor wheels nor the ground! Pre-requisites: •...
  • Page 89 • Loosen the screw (1) using the Allen key. • Set the desired angle. • Re-tighten the screw.

  • Page 90: Setting The End Stop Of The Footrest

    9.2.1.3 Setting the end stop of the footrest Pre-requisites: • 1x 6 mm Allen key • 1x 10 mm open-ended spanner The end position of the footrest is determined by means of a rubber stop (1). The rubber stop can be screwed in or out (A) or pushed up or down (B).
  • Page 91 • Use the Allen key to loosen the screw (1) and swivel the footrest upward in order to access the rubber stop. • Use the open-ended spanner to loosen the counternut (1).
  • Page 92 • Move the rubber stop to the desired position • Re-tighten the counternut • Move the footrest to the desired position. • Re-tighten the screw.

  • Page 93: Adjusting The Length Of The Footrest

    9.2.1.4 Adjusting the length of the footrest PLEASE NOTE: Danger of injury due to incorrect adjustment of the footrests and legrests. • Before and during every journey it is imperative to ensure that the legrests contact neither the castor wheels nor the ground! Pre-requisites: •...

  • Page 94: Manually Height Adjustable Legrest 90° - 0

    9.2.2 Manually height adjustable legrest 90° - 0° 9.2.2.1 Swivelling the legrest outward and/or removing The small unlocking button is located on the upper section of the legrest. When the legrest is unlocked, it can be swivelled inward or outward when getting into wheelchair as well as being removed completely.

  • Page 95: Setting The Angle

    9.2.2.2 Setting the angle PLEASE NOTE: Danger of injury due to incorrect adjustment of the footrests and legrests. • Before and during every journey it is imperative to ensure that the legrests contact neither the castor wheels nor the ground! •...
  • Page 96 • Hit the knob to release the locking mechanism. • Set the desired angle.
  • Page 97 • Turn the knob clockwise to tighten it.

  • Page 98: Setting The End Stop Of The Legrest

    9.2.2.3 Setting the end stop of the legrest Pre-requisites: • 1x 10 mm open-ended spanner The end position of the legrest is determined by means of a rubber stop (A). The rubber stop can be screwed in or out (A) or pushed up or down (B).
  • Page 99 • Loosen the locking knob (1) counter-clockwise at least one turn. • Hit the knob to release the locking mechanism.
  • Page 100 • Swivel the legrest upward in order to access the rubber stop. • Use the open-ended spanner to loosen the counternut (1).
  • Page 101 • Move the rubber stop to the desired position • Re-tighten the counternut • Move the legrest to the desired position. • Re-tighten the locking knob.

  • Page 102: Adjusting The Length Of The Legrest

    9.2.2.4 Adjusting the length of the legrest PLEASE NOTE: Danger of injury due to incorrect adjustment of the footrests and legrests. • Before and during every journey it is imperative to ensure that the legrests contact neither the castor wheels nor the ground! Pre-requisites: •...

  • Page 103: Adjusting The Depth Of The Calf Plate

    9.2.2.5 Adjusting the depth of the calf plate The depth of the calf plate can be adjusted via the holding plate. The holding plate hole combinations allow 5 different depth settings. Pre-requisites: • 1x 10 mm open-ended spanner • Use the open-ended wrench to loosen the nut (1) and remove.

  • Page 104: Adjusting The Height Of The Calf Pad

    9.2.2.6 Adjusting the height of the calf pad Pre-requisites: • 1x 4 mm Allen key • Use the Allen key to loosen the screws (1). • Adjust to the desired position. • Re-tighten the screws.

  • Page 105: Unlocking And Swivelling The Calf Plate Backward When Alighting

    9.2.2.7 Unlocking and swivelling the calf plate backward when alighting • Press the calf plate straight down. • Unlock the legrest and swivel outward. The calf plate swivels backward on its own.

  • Page 106: Adjusting The Angle Adjustable Foot Plate

    • Lift leg over the heel strap and place on the ground. 9.2.2.8 Adjusting the angle adjustable foot plate Pre-requisites: • 1x 5 mm Allen key • Use the Allen key to loosen both set screws on the foot plate. •...

  • Page 107: Adjusting The Angle And Depth Adjustable Foot Plate

    9.2.2.9 Adjusting the angle and depth adjustable foot plate Pre-requisites: • 1x 5 mm Allen key • Use the Allen key to loosen the set screw on the foot plate (1). • Adjust the foot plate to the desired angle or depth. •...

  • Page 108: Manually Height Adjustable Legrest 80° - 0° With Ergonomic Length Adjustment

    9.2.3 Manually height adjustable legrest 80° - 0° with ergonomic length adjustment 9.2.3.1 Swivelling the legrest outward and/or removing The small unlocking button is located on the upper section of the legrest. When the legrest is unlocked, it can be swivelled inward or outward when getting into wheelchair as well as being removed completely.

  • Page 109: Setting The Angle

    9.2.3.2 Setting the angle PLEASE NOTE: Danger of crushing! • Do not reach inside the swivelling range of the legrest! PLEASE NOTE: Danger of injury due to incorrect adjustment of the footrests and legrests. • Before and during every journey it is imperative to ensure that the legrests contact neither the castor wheels nor the ground! •...
  • Page 110 • Lowering: Keep the legrest in the foot plate area, pull the lateral adjusting lever (1) and lower the legrest slowly.

  • Page 111: Adjusting The Length Of The Legrest

    9.2.3.3 Adjusting the length of the legrest PLEASE NOTE: Danger of injury due to incorrect adjustment of the footrests and legrests. • Before and during every journey it is imperative to ensure that the legrests contact neither the castor wheels nor the ground! Pre-requisites: •...

  • Page 112: Adjusting The Depth Of The Calf Plate

    9.2.3.4 Adjusting the depth of the calf plate The depth of the calf plate can be adjusted via the holding plate. The holding plate hole combinations allow 5 different depth settings. Pre-requisites: • 1x 10 mm open-ended spanner • Use the open-ended wrench to loosen the nut (1) and remove.

  • Page 113: Adjusting The Height Of The Calf Pad

    9.2.3.5 Adjusting the height of the calf pad Pre-requisites: • 1x 4 mm Allen key • Use the Allen key to loosen the screws (1). • Adjust to the desired position. • Re-tighten the screws.

  • Page 114: Unlocking And Swivelling The Calf Plate Backward When Alighting

    9.2.3.6 Unlocking and swivelling the calf plate backward when alighting • Press the calf plate straight down. • Unlock the legrest and swivel outward. The calf plate swivels backward on its own.

  • Page 115: Adjusting The Angle Adjustable Foot Plate

    • Lift leg over the heel strap and place on the ground. 9.2.3.7 Adjusting the angle adjustable foot plate Pre-requisites: • 1x 5 mm Allen key • Use the Allen key to loosen both set screws on the foot plate. •...

  • Page 116: Adjusting The Angle And Depth Adjustable Foot Plate

    9.2.3.8 Adjusting the angle and depth adjustable foot plate Pre-requisites: • 1x 5 mm Allen key • Use the Allen key to loosen the set screw on the foot plate (1). • Adjust the foot plate to the desired angle or depth. •...

  • Page 117: Electrically Height Adjustable Legrest 80° - 0° With Ergonomic Length Adjustment

    9.2.4 Electrically height adjustable legrest 80° - 0° with ergonomic length adjustment 9.2.4.1 Swivelling the legrest outward and/or removing The small unlocking button is located on the upper section of the legrest. When the legrest is unlocked, it can be swivelled inward or outward when getting into wheelchair as well as being removed completely.

  • Page 118: Setting The Angle

    9.2.4.2 Setting the angle PLEASE NOTE: Danger of crushing! • Do not reach inside the swivelling range of the legrest! PLEASE NOTE: Danger of injury due to incorrect adjustment of the footrests and legrests. • Before and during every journey it is imperative to ensure that the legrests contact neither the castor wheels nor the ground! The electrically height adjustable legrest is operated via the remote.

  • Page 119: Adjusting The Length Of The Legrest

    9.2.4.3 Adjusting the length of the legrest PLEASE NOTE: Danger of injury due to incorrect adjustment of the footrests and legrests. • Before and during every journey it is imperative to ensure that the legrests contact neither the castor wheels nor the ground! Pre-requisites: •...

  • Page 120: Adjusting The Depth Of The Calf Plate

    9.2.4.4 Adjusting the depth of the calf plate The depth of the calf plate can be adjusted via the holding plate. The holding plate hole combinations allow 5 different depth settings. Pre-requisites: • 1x 10 mm open-ended spanner • Use the open-ended wrench to loosen the nut (1) and remove.

  • Page 121: Adjusting The Height Of The Calf Pad

    9.2.4.5 Adjusting the height of the calf pad Pre-requisites: • 1x 4 mm Allen key • Use the Allen key to loosen the screws (1). • Adjust to the desired position. • Re-tighten the screws.

  • Page 122: Unlocking And Swivelling The Calf Plate Backward When Alighting

    9.2.4.6 Unlocking and swivelling the calf plate backward when alighting • Press the calf plate straight down. • Unlock the legrest and swivel outward. The calf plate swivels backward on its own.

  • Page 123: Adjusting The Angle Adjustable Foot Plate

    • Lift leg over the heel strap and place on the ground. 9.2.4.7 Adjusting the angle adjustable foot plate Pre-requisites: • 1x 5 mm Allen key • Use the Allen key to loosen both set screws on the foot plate. •...

  • Page 124: Adjusting The Angle And Depth Adjustable Foot Plate

    9.2.4.8 Adjusting the angle and depth adjustable foot plate Pre-requisites: • 1x 5 mm Allen key • Use the Allen key to loosen the set screw on the foot plate (1). • Adjust the foot plate to the desired angle or depth. •...

  • Page 125: Electrical System

    Electrical system 10.1 Electronics protection system The vehicle's electronics are equipped with an overload-protection system. If the motors are put under considerable strain for a longer period of time (for example, when driving up a steep hill) and especially when the ambient temperature is high, then the electronic system could overheat.

  • Page 126: 10.1.1 The Main Fuse

    NOTE A defective main fuse may be replaced only after checking the entire electric system. An Invacare® specialised dealer must perform the replacement. You can find information on the fuse type in chapter "Technical specifications" starting on page 164. All electrical equipment fitted to the wheelchair is protected against overload by the main fuse.

  • Page 127: Batteries

    10.2 Batteries Power is supplied by two 12 V batteries. The batteries are maintenance-free and only need regular charging. In the following, you find information on how to charge, handle, transport, store, maintain, and use batteries. 10.2.1 Charging the batteries 10.2.1.1 General information on charging New batteries should always be fully charged once before their first use.

  • Page 128: 10.2.1.3 How To Charge The Batteries

    10 °C. • Use only charging devices in Class 2. This class of chargers may be left unattended during charging. All charging devices which are supplied by Invacare® comply with these requirements.

  • Page 129: 10.2.1.4 How To Disconnect The Batteries After Charging

    Risk of explosion and destruction of batteries if the wrong battery charger is used! • Only ever use the battery charger supplied with your vehicle, or a charger that has been approved by Invacare®. Risk of electric shock and damage to the battery charger if it gets wet! •...

  • Page 130: 10.2.2 Storage And Maintenance

    10.2.2 Storage and Maintenance Follow the instructions listed below to ensure safe use and longevity of the batteries: • Always store the batteries fully charged. • Do not leave the batteries in a low state of charge for an extended length of time. Charge a discharged battery as soon as possible.
  • Page 131 The last 3 LED (two red and one orange) mean a remaining capacity of about 15 %. • Driving with blinking red LED’s means an extreme stress for the battery and should be avoided under normal circumstances. • When only one red LED is blinking, the Battery Safe feature is enabled. From this time, speed and acceleration is reduced drastically.

  • Page 132: 10.2.4 Transporting Batteries

    • Under normal operation, once a month the battery should be discharged until all green and orange LED are off. This should be done within one day. A 16 hour charge afterwards is necessary as reconditioning. 10.2.4 Transporting batteries The batteries supplied with your electric vehicle are not hazardous goods. This classification is based on the German GGVS Hazardous Goods Road Transport Ordinances, and the IATA/DGR Hazardous Goods Rail Transport / Air Transport Ordinances.
  • Page 133 • Only ever transport damaged batteries in an appropriate acid-resistant receptacle. • Wash all objects that have come into contact with acid with lots of water. Disposing of dead or damaged batteries correctly Dead or damaged batteries can be given back to your dealer or directly to Invacare®.

  • Page 134: 10.2.5.3 Removing The Batteries

    10.2.5.3 Removing the batteries CAUTION: Risk of fire and burns if battery poles are bridged! • When replacing the batteries the battery poles MUST NOT come into contact with metal parts of the wheelchair causing bridging. • Be sure to replace the battery pole caps after the batteries have been replaced. WARNING: Risk of fire and burns due to damage to the battery cables! •...
  • Page 135 • Run the seat lifter to the top position. • Remove legrests • Pull out the actuator bolt locking at the belt.
  • Page 136 • One person now pulls the seat upwards, and a second person ensures that the actuator bolt head (1) is guided out of its mounting and does not jam.
  • Page 137 • Push the holding mechanism (1) completely to the front so that it engages. • Run the actuator bolt down completely. • Pull the cladding off forwards.
  • Page 138 • Loosen the screws (1) on both sides with the 8 mm Allen key and remove. • Press the bottom actuator holder lightly inwards together with the regulator motor.
  • Page 139 • ..then lift (1) and pull out completely to the front (2). In doing so it can be helpful to use one hand under the chassis to guide the actuator holder locking pin into the position from which it can be pulled out upwards. •...
  • Page 140 • Remove the terminal cover from the battery terminals (1). • First undo the bolt on the negative terminal (black cable) with the 11 mm jaw spanner. • After this, undo the bolt on the positive terminal (red cable). CAUTION! Danger of crushing! •...
  • Page 141 CAUTION! Fire hazard! Cables can be jammed and frayed. • Please ensure that the cables are correctly located. They may not protrude into the lifter area. Use cable clamps if necessary. When installing new batteries, no cables may be located between the front battery and the lifter actuator! If so, they can be damaged when the lifter is actuated! WRONG! RIGHT!
  • Page 142 CAUTION! Danger of crushing! • Please ensure that the actuator head slides into the top bracket. • Run the actuator bolt into the top position and ensure that it slides into the top bracket (1).
  • Page 143 • Raise the seat slightly and release the holding mechanism (1). Lower the seat slowly until the weight of the lifter is resting on the actuator again. • Check all vehicle functions. • Check the new battery status and charge completely.

  • Page 144: Care And Maintenance

    Maintenance encompasses different areas, such as everyday care and cleaning, inspection checks, repair tasks and refurbishment. NOTE: Have your vehicle checked once a year by an authorised Invacare® dealer in order to maintain it's driving safety and roadworthiness. 11.1...

  • Page 145: Inspection Checks

    Service Manual for this device, which can be obtained from Invacare®. That Manual, however, is intended to be used by trained and authorised service technicians, and describes tasks which are not intended to be performed by...
  • Page 146 Maintenance Jobs Seat and backrest padding: - Check for perfect condition. Side part and armrest: - Are all fixing elements installed? - Can armrests / side panels be removed and installed without too much physical effort? - Are armrests secured in their positions? Legrests: - Do legrests lock into place without any problem (only applies to detachable legrests)?
  • Page 147 To ensure driving safety and roadworthiness, you should have your wheelchair inspected and serviced by your authorised dealer once a year. A complete checklist of necessary maintenance work can be found in the Workshop Manual, which can be obtained from Invacare®.

  • Page 148: Maintenance- And Repair Work

    "Technical specifications" on page 164, or consult the Service Manual, available from Invacare® (in this connection please see the addresses and phone numbers in section "How can you get in touch with Invacare®?" on page 3). In case you require assistance, please contact your Invacare® Dealer.

  • Page 149: Repairing Punctures (Drive Wheel With Gb Motor And Pneumatic Tyres)

    12.1.1 Repairing punctures (drive wheel with GB motor and pneumatic tyres) EXPLOSION HAZARD! The wheel will explode if you do not let the air out of the tyre before removing the wheel! • Always let the air out of the tyre before removing it (press in the pin in the middle of the valve)! Injury hazard!If the wheel has been insufficiently tightened during assembly, it can become loosened during driving!
  • Page 150 Disassembly • Block up the vehicle (place wooden blocks under frame). • Unscrew valve cap. • Depressurise tyre by pressing in the pin in the valve (1). • Unscrew 5 screws (2). • Remove the wheel rim halves. • Remove the inner tube from the tyre. NOTE: If the old inner tube is to be repaired and re-used, and has become wet during repair, you can make replacement easier by sprinkling the inner tube with a little talcum powder.
  • Page 151 • Repair inner tube and replace, or insert new. • Replace the inner tube in the tyre. • Insert the wheel rim halves once again. • Insert the screws and tighten slightly. • Pump a little air into the inner tube. •...

  • Page 152: Transport

    Transport CAUTION: Injury hazard or material damage if a power wheelchair which is fitted with a table is transported in a vehicle! • If a table is fitted, always remove it before transporting the wheelchair. 13.1 Transferring the wheelchair to a vehicle WARNING: The wheelchair is in danger of tipping over if it is transferred to a vehicle while the driver is still seated in the wheelchair! •...

  • Page 153: Use Of The Wheelchair As A Seat In A Vehicle

    • An alternative way to safely use this wheelchair as a vehicle seat may be by using the Docking Station system if the wheelchair is compatible with that system, available separately! Please contact Invacare if you require the details. WARNING: Danger of injury or damage to the wheelchair or to the transporting vehicle, if the legrests are in a raised position while the wheelchair is used as a vehicle seat! •...
  • Page 154 Caution: There is a danger of injury if the wheelchair is not properly secured during use as a vehicle seat! • If possible, the user should always leave the wheelchair to use a vehicle seat and the safety belts provided with the vehicle. •...
  • Page 155 (UK for example), but may also be obtained from Invacare® as an option in other countries. This power wheelchair complies with the requirements of ISO 7176-19:2001 and may be used as a vehicle seat in connection with an anchoring system that has been checked and approved in accordance with ISO 10542.

  • Page 156: 13.2.1 How The Wheelchair Is Anchored In A Vehicle For Use As A Vehicle Seat

    13.2.1 How the wheelchair is anchored in a vehicle for use as a vehicle seat The power wheelchair is fitted with four anchoring points, which are labelled with the symbol shown on the right. Snap hooks or belt loops can be used for fixation.

  • Page 157: 13.2.2 How The User Is Secured Within The Wheelchair

    13.2.2 How the user is secured within the wheelchair CAUTION: There is a danger of injury if the user is not properly secured within the wheelchair! • Even if the wheelchair is fitted with a postural belt, this is no substitute for a proper safety belt which complies with ISO 10542 in the transport vehicle.
  • Page 158 This can cause the neck to be hyperextended during collisions! • A headrest must be installed! The headrest optionally supplied for this mobility device by Invacare® is perfectly suitable for use during transport. • The headrest must be adjusted to the user's ear height.
  • Page 159 Seat belts may not be held at a distance The pelvic belt should be positioned in the from the user's body using parts of the area between the user's pelvis and thighs wheelchair such as armrests or wheels. so that it is unobstructed and not too loose. The ideal angle of the pelvic belt to the horizontal is between 45°...
  • Page 160 The safety belt installed in the transporting vehicle should be applied as shown in the illustration at right. 1) Centre line of the body 2) Centre of the sternum...

  • Page 161: Securing The Wheelchair For Transport Without Passengers

    CAUTION: Injury hazard! ® • If you are unable to fasten your electric wheelchair securely in a transport vehicle, Invacare recommends that you do not transport it! • Before transporting your wheelchair, make sure the motors are engaged and that the Joystick Box is switched off.

  • Page 162: Refurbishment

    • Cleaning and disinfection. Please see chapter "Care and maintenance" on page 144. • Inspection according to service plan. Please consult service instructions, available from Invacare®. • Adaptation to the user. Please see chapter "Adjusting the wheelchair to the user's seating...

  • Page 163: Disposal

    • Electric components and printed circuit boards are disposed of as electronic scrap. • Exhausted or damaged batteries can be returned to your medical equipment supplier or Invacare®. • Disposal must be carried out in accordance with the respective national legal provisions.

  • Page 164: Technical Specifications

    Technical specifications The technical information provided hereafter applies to a standard configuration or represents maximum achievable values. These can change if accessories are added. The precise changes to these values are detailed in the sections for the respective accessories. Permissible operating and storage conditions Temperature range for operation according to ISO 7176-9: •...
  • Page 165 Driving characteristics Speed • 6 km/h • 10 km/h • 12 km/h Min. braking distance • 1000 mm (6 km/h) • 2100 mm (10 km/h) • 2900 mm (12 km/h) Max. safe slope ****** • 11,3° (20 %) according to manufacturer’s specifications with 150 kg payload, 4°...
  • Page 166 Dimensions Standard Contour Recaro Flex Junior Seat width • 300/350/ 380 mm Overall length (incl. standard • 1160 mm legrest) Seat height **** • 400 mm (+300 mm with lifter) • 470 mm • 470 mm (+300 mm with lifter) (+300 mm with •...
  • Page 167 Dimensions Standard Contour Recaro Flex Junior Backrest angle • -10°, 0°, • -10° ... • 0°...+45° • -10° … • +5° … +7,5°, +45° +45° +35° +15°, (man.) +22,5°, • +2° … +30° +30° (man.) (electr.) • 0° ... +16° (electr.) Armrest height •...
  • Page 168 **** Measured without seat cushion ***** The actual kerb weight depends on the fittings your mobility aid has been supplied with. Every Invacare® mobility aid is weighed when leaving the works. Please refer to the nameplate for the kerb weight (including batteries) measured.

  • Page 169: Inspections Performed

    It is confirmed by stamp and signature that all jobs listed in the inspection schedule of the Service and Repair Instructions have been properly performed. The list of the inspection jobs to be performed can be found in the Service Manual which is available through Invacare®. Delivery Inspection...

This manual is also suitable for:

Typhoon ii standardTyphoon ii contourTyphoon ii recaroTyphoon ii flexTyphoon ii junior

Table of Contents