Sony mz-dh10p Service Manual page 20

MZ-DH10P
Ver. 1.2
3-6-2. Destination setting
1. Enter the test mode (Display Check mode).
2. Press the [VOL+] key to enter the Manual mode.
3. Press the key five time to select the item number 0113
>
and display as follows.
Display of the remote commander
113 DistFL **
adjustment value (hexadecimal)
4. Press the [VOL+]/[VOL--] key and set the according value to
each destination referring to the following table.
5. Press the ,
u ENT
+
remote commander to write the adjusted value.
6. Press the key to select the item number 0114.
>
7. Repeat adjustment from step 3.
8. Press the key four times and back to the Display Check
x
mode.
Destination
US
AEP and UK
Chinese and Tourist
Table 3-6-2. Destination Setting
3-6-3. Other setting
Procedure:
1. Enter the test mode (Display Check mode).
2. Press the [VOL+] key to enter the Manual mode.
3. Press the [VOL+] key once and press the
select the item number 1113 and display as follows.
Display of the remote commander
113 SS**$$##
adjustment value (hexadecimal)
4. Adjust with [VOL+]/[VOL--] keys so that the adjustment value
of "**" on the LCD becomes "1A".
5. Press the ,
ENT
+ u
remote commander to write the adjusted value. ($$ blinks and
disc mark rotates on the LCD)
6. Adjust with [VOL+]/[VOL--] keys so that the adjustment value
of "$$"on the LCD becomes "20".
7. Press the ,
ENT
+ u
remote commander to write the adjusted value. (## blinks and
disc mark rotates on the LCD)
8. Adjust with [VOL+]/[VOL--] keys so that the adjustment value
of "##"on the LCD becomes" 5E".
9. Press the ,
ENT
+ u
remote commander to write the adjusted value.
10. Press the [VOL+] key once to change the adjustment value of
"**" on the LCD into "1B".
11. Press the ,
u ENT
+
remote commander to write the adjusted value. ($$ blinks and
disc mark rotates on the LCD)
12. Adjust with [VOL+]/[VOL--] keys so that the adjustment value
of "$$"on the LCD becomes "F1".
13. Press the ,
u ENT
+
remote commander to write the adjusted value. (## blinks and
disc mark rotates on the LCD)
14. Adjust with [VOL+]/[VOL--] keys so that the adjustment value
of "##"on the LCD becomes "1A".
20
key on the set or key on the
–
Setting value
Item No. 0113 Item No. 0114
28 80
A0 80
24 80
key five time to
>
key on the set or key on the
–
key on the set or key on the
–
key on the set or key on the
–
key on the set or key on the
–
key on the set or key on the
–
15. Press the ,
ENT
u
+
remote commander to write the adjusted value.
16. Press the key four times and back to the Display Check
x
mode.
3-7. Servo Overall Adjustment
Note1: Be sure to adjustment so that the set is horizontal and the LCD is
upside. Unless performed in that state, it is not adjusted correctly.
Note2: If NG is displayed in the middle of this adjustments, perform "3-2.
Initialize The Adjustment Value" and "3-6. Setting The Adjustment
Values" again, then retry this adjustments from step 1.
Procedure:
1. Enter the test mode (Display Check mode).
2. Press the [VOL--] key to enter the Overall Adjustment mode.
3. Insert the CD adjustment disc (TDYS-1).
4. Put the main unit horizontal so that the LCD becomes upside,
and press the key.
.
5. Wait until "CD OK" is displayed on the LCD.
6. Insert the MD1/HiMD1 hybrid adjustment disc
(MDW-74/GA2).
7. Put the main unit horizontal so that the LCD becomes upside,
and press the key.
>
8. Wait until "MD1 OK" is displayed on the LCD.
9. Insert the Hi-MD3 adjustment disc (HMD1GSDJ).
10. Put the main unit horizontal so that the LCD becomes upside,
and press the [VOL+] key.
11. Wait until "HMD3OK" is displayed on the LCD.
12. Eject the disc and close the lid.
13. Put the main unit horizontal so that the LCD becomes upside,
and press the [VOL--] key.
14. Wait until "OfstOK" is displayed on the LCD.
15. Press the key and back to the Display Check mode.
x
3-8. Resume Clear
Procedure:
1. Enter the test mode (Display Check mode).
2. Press the [VOL+] key to enter the Manual mode.
3. Press the [VOL+] key once, press the
[VOL--] key once, press the
key twice, press the
>
number 1933.
4. Press the ,
u ENT
+
remote commander to resume clear.
5. Press the key four times and back to the Display Check
x
mode.
3-9. Releasing The Test Mode
Refer to the "SECTION 4. TEST MODE". (See page 13)
key on the set or key on the
–
key once, press the
>
key once, and press the [VOL+]
>
key three times to select the item
key on the set or key on the
–