Table of Contents
Advertisement
Available languages
Available languages
10 • ENGLISH
c. Disconnect the plug from the power source and/or
the battery pack from the power tool before
making any adjustments, changing accessories,
or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power
tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f.
Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
6. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main
voltage corresponds to the voltage on the rating
plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
Stanley Service Center or an equally qualified
person in order to avoid damage or injury. If the
power cord is replaced by an equally qualified
person, but not authorized by Stanley, the
warranty will not be valid.
Using an Extension Cable
An extension cable should not be used unless absolutely
necessary. Use of an improper extension cable could
resultin a risk of fire and electric shock. If an extension
cable must be used, use only those that are approved by
the country's Electrical Authority. Make sure that extension
cord is in good condition before using. Always use the
cord that is suitable for the power input of your tool (see
technical data on name plate). The minimum conductor
size is 1.5mmWhen using a cable reel, always unwind the
cable completely.
7. Labels on tool
The label on your tool may include the following symbols:
Hz .......
Read
Instructions
W ........
Manual
min .....
Use Eye
Protection
Use Ear
Protection
V ........
Volts
n
.......
0
A ........
Amperes
FEATURES (Fig. A)
Your Stanley small angle grinder has been designed
for grinding, cutting, wire-cup brushing and sanding
applications.
1. On/off switch
2. Side handle*
3. Spindle lock
4. Wheel guard
5. Inner flange
6. Outer flange
* Not all models contain side handle
Assembly and Adjustment
¡Warning! Prior to assembly and adjustment always
unplug the tool.
MOUNTING AND REMOVING THE GUARD (FIG. B)
Mounting
f Place the angle grinder on a flat and steady surface,
spindle (7) up (Fig. B1)
f Align the 3 lugs (8) with the 3 slots (9) in gearcase
cover.
f Press the guard (4) down and turn it in the direction
of the arrow until it is in the working position providing
maximum protection to the user (Fig. B2)
f Insert the bolt (11) to the holes on the bracket. Screw
the nut (12) on the thread of the bolt. Use crosshead
screwdriver (13) (not supply) to tighten the bolt and
nut.
¡Warning! Do not operate the grinder with a loose
guard.
Removing
f Follow the procedure above in reverse order.
MOUNTING AND REMOVING GRINDING
WHEELS OR CUTTING DISCS (FIG. C & D)
Your grinder comes with two reversible flanges to
accommodate a wide variety of different accessories.
Make sure the correct sides of the flanges are being used
ensuring no excessive play between the accessory and
the flanges.
Hertz
...... Class II
Watts
....
minutes
.....
Alternating
....
Current
.....
Direct
.../min..
Current
No-Load
Speed
Construction
Earthing
Terminal
Safety Alert
Symbol
Revolutions
or Recipro-
cation per
minute
Advertisement
Table of Contents
