Further, ViewSonic reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation of ViewSonic to notify any person of such revision or changes.
(13) Small amount of materials having no flammability grade is used in the LCD module. The LCD module should be supplied by power complied with requirements of Limited Power Source (IEC60950 or UL1950), or be applied exemption. ViewSonic Corporation N2750w-2G Confidential - Do Not Copy...
Page 5
Do not touch and that may cause “Mura” the surface of the polarizer. Take out the monitor with cushions Taking out the monitor by grasping the LCD panel. That may cause “Mura” ViewSonic Corporation N2750w-2G Confidential - Do Not Copy...
Page 6
Place the monitor on a clean and soft foam pad. Placing the monitor on foreign objects. That could scratch the surface of the panel or cause “Mura” ViewSonic Corporation N2750w-2G Confidential - Do Not Copy...
DC Level Sync Pulse Typical. 0.35 V Audio Characteristics: AF Output Level Measured via LP 20 kHz Typical. 0.45Vrms Filter, RMS Decoder, 50us De-emphasis 10% (max.) 40 dB (min.) Compatible system TUNER SECAM/PAL ViewSonic Corporation N2750w-2G Confidential - Do Not Copy...
Page 8
+/- 3 db (at 1KHz @1W) +/- 3 db (at 1KHz @1W) (100Hz ~ 10KHz) Total Harmonic Distortion (1KHz @1W) Signal to Noise (1KHz @1W) 30 dB (40Hz to 15KHz) 40dB(400Hz to 20 kHz) ViewSonic Corporation N2750w-2G Confidential - Do Not Copy...
Page 9
Power Factor Correction Compliant with EN60065 5. Firmware & OSD The product firmware of VS11404-1G shall have a firmware version of V:P01. changes/revisions afterward shall also be pre-approved by ViewSonic in written. For VS11404-1G, its firmware shall have a built-in frequency table for PAL/SECAM off-air TV/CATV implementation.
Page 10
Switch between main screen and sub screen during in PIP or POP P.input Sub source selection during in PIP or POP Displaying captions during closed caption source and closed caption mode select V-chip Set V-chip rating ViewSonic Corporation N2750w-2G Confidential - Do Not Copy...
Page 11
Molded Plastic Workmanship shall be inspected according to ViewSonic Molded Plastic Parts Specification, VSCMPPSPEC001V1.2. Screen Printed Parts, Bird Logo Artwork shall be provided and confirmed by ViewSonic. Recess Rear Label A label identifying the product name, model/serial number and FCC ID/Logo shall be placed into the rear label recess located on the rear panel of the chassis.
Page 12
Sample of textured color chips, plastic material specification, and Material Safety Data Sheets shall be submitted to ViewSonic prior to Mass Production Release. In addition, all exterior surfaces shall have uniform texture/color. The maximum acceptable gap between the buckets to bezel plastic pieces shall be within 1.5 mm. The maximum acceptable gap between LCD panel and bezel shall be within 2.5 mm.
VOL+ and MENU buttons again to unlock it. 2. Press VOL- and VOL+ buttons at the same time to lock OSD menu, and press VOL- and VOL+ buttons again to unlock it. ViewSonic Corporation N2750w-2G Confidential - Do Not Copy...
Power Input (AC Input) Connect to LCD TV and AC outlet with the power cord. AC Power Switch (Must be turned on) Without using for a period of time, turn the switch off. ViewSonic Corporation N2750w-2G Confidential - Do Not Copy...
Remote Control ViewSonic Corporation N2750w-2G Confidential - Do Not Copy...
Page 16
32 FLASHBACK Return to previos channel 33 DUAL I / II MTS (Multi-Channel TV Sound) select 34 FREEZE Freeze picture Note: PIP means Picture In Picture. POP means Picture Out Of Picture. ViewSonic Corporation N2750w-2G Confidential - Do Not Copy...
Page 17
• Select Program for Sub-screen Press P+ and P- to select the program of sub-screen. Sound • Sound Mode Select Press SMART. S to select the sound mode between Movie, Music, Speech, and User. ViewSonic Corporation N2750w-2G Confidential - Do Not Copy...
• Treble: To adjust the treble (It is active in TV/ SCRT1/ SCART2/ SCART2-SVIDEO. However, in other input sources, it is only active when sound mode is in “User” condition). • Balance: To adjust left and right audio balance. ViewSonic Corporation N2750w-2G Confidential - Do Not Copy...
Page 19
5. Move your cursor to “Fine Tune”, and adjust the picture with ◄►. 6. Move to Store, then store the instruction with ENTER Note: The channel will be stored instead of the former program. ViewSonic Corporation N2750w-2G Confidential - Do Not Copy...
Page 20
1. Move your cursor to “From,” and press ◄► to select channel 1. 2. Move your cursor to “To,” and press ◄► to select channel 2. 3. Move your cursor to “Store,” and confirm the instruction with ENTER 4. Press MENU to exit. ViewSonic Corporation N2750w-2G Confidential - Do Not Copy...
• Clock: To adjust delay time of clock in order to reduce the noise of picture. • Phase: To adjust delay time of phase in order to reduce the noise of picture. ViewSonic Corporation N2750w-2G Confidential - Do Not Copy...
Page 22
• Duration: To automatically shut off the OSD after a preset period of time passed. Use ◄► to preset the time from 5 to 60 seconds. • Halftone: To adjust background transparency of OSD. ViewSonic Corporation N2750w-2G Confidential - Do Not Copy...
The MST5151A-LF chip is targeted for the applications of high-end LCD-TV. It will accept all HDTV video signals for flat panel display. It comes with 256-pin LQFP package. General Feature: 1M*32Bit*4Banks SDRAM controller for interlaced to progressive video processing and ViewSonic Corporation N2750w-2G Confidential - Do Not Copy...
Page 24
The Antenna receive the TV signal and modulate it to the CVBS signal which can be recognized by the decoder and FM-stereo/FM-mono/NICAM audio signal output to the sound Automatic standard decoder IC MSP3410G. The MCU can automatic detect the tuner and send order by serial bus. ViewSonic Corporation N2750w-2G Confidential - Do Not Copy...
Page 25
“ENTER” key to switch to ON, press ”POWER” key to restart the TV, and then press ”ENTER” key to enter BURN IN mode. To exit BURN IN mode, repeat the procedure again, but switch the column of BURN IN to “OFF”. ViewSonic Corporation N2750w-2G Confidential - Do Not Copy...
Page 26
A. In DVI MODE, switch TIMING according to the FACTORY PRESET TIMING TABLE, and confirm that the screen is normal B. Confirm that the four TIMING screens of 408i, 480P, 720P, and 1080i are normal C. Confirm that HDMI DVD functions normally ViewSonic Corporation N2750w-2G Confidential - Do Not Copy...
Page 27
Examines whether DUAL FUNCTION is normal under DUAL MODE; whether DUAL SENSITIVITY is normal when input signal is under LEVEL<=36dBu. G. Examines whether the sound does receive the image disturbance, Judgment basis: Whether there is unusual sound, input signal LEVEL<=36dBu,and STEREO ViewSonic Corporation N2750w-2G Confidential - Do Not Copy...
Page 28
AV output test method is in the same way. B. Under any pattern except PC pattern, The Audio output meets active extra speaker, examines whether the extra speaker makes the sound. ViewSonic Corporation N2750w-2G Confidential - Do Not Copy...
Page 29
All timings must be properly PHASED, SIZED, and CENTERED. Aspect Ratio=Resolution to which the native signal is SCALED and CENTERED 1:1=Centered, 1:1 Pixel Correlation, No Scaling. No Filtering, Image must be properly ViewSonic Corporation N2750w-2G Confidential - Do Not Copy...
Page 30
After final QC step, we have to erase all saved changes again and restore the factory defaults. You should do “All Mode Reset” again. Power Off LCD TV. Turn off the LCD TV by pressing “Power” button. ViewSonic Corporation N2750w-2G Confidential - Do Not Copy...
Page 31
N2750W(2G) LCD TV DDC Card RS-232 Cable VGA Cable Barcode Reader 2.2 Setup Procedure 2.2.1 Connect VGA Card and DDC Card with RS-232 cable. 2.2.2 Barcode Reader connects with keyboard and PC keyboard port. ViewSonic Corporation N2750w-2G Confidential - Do Not Copy...
Page 32
2.3.1 Run DDC.exe 2.3.2 Choose model number and conform the Time then Press “ENTER” key. 2.3.3 When appear the PIC “ choose DDC Card”, Press ALT+2 Enter DDC 2B test interface Choose DDC Card ViewSonic Corporation N2750w-2G Confidential - Do Not Copy...
Page 33
2.3.4 Press F8 to choose corresponding model. DAT (N2750W(2G)-A.DAT press “ENTER” key) 2.3.5 Press F9 enter the download interface ViewSonic Corporation N2750w-2G Confidential - Do Not Copy...
Page 34
2.3.6 Key in the serial number or use the barcode reader to scan the barcode of the LCD TV, and press “ENTER” key. 2.3.7 The successful picture is as follows. “Compare EDID:OK! Press any key to continue”. ViewSonic Corporation N2750w-2G Confidential - Do Not Copy...
Page 35
2.4 Check Method Use ViewSonic EDID Editor Connect the N2750W(2G) LCD TV to PC with VGA Cable. Execute the EDID Editor, then Press Ctrl+F5. If the DDC is correct, you can see the information as follow: ViewSonic Corporation N2750w-2G Confidential - Do Not Copy...
Page 36
3.2.2 Connect P1 of Fixture with N2750W(2G) LCD TV by VGA Cable. 3.2.3 Connect Power Cord to N2750W(2G) LCD TV. 3.2.4 Connect PC to the additional LCD TV. 3.3 ISP Download program procedure 3.3.1 HARDWARE CONNECT STATUS: ViewSonic Corporation N2750w-2G Confidential - Do Not Copy...
Page 37
3.3.2 DOWNLOAD ISP PROGRAM Step 1: Execute ISP.exe ViewSonic Corporation N2750w-2G Confidential - Do Not Copy...
Page 38
OK Button. Step 3: Load file Press the Select File 0 and Select File 1 button to select the file (File 0 and File 1) will be downloaded. (*.Hex) ViewSonic Corporation N2750w-2G Confidential - Do Not Copy...
Page 39
ViewSonic Corporation N2750w-2G Confidential - Do Not Copy...
Page 40
Pressing the ConNect button to test whether the communication is well. Step 5: Run Pressing the Program All to start download program. Pressing the ‘確定’ Button to finish the download program procedure. ViewSonic Corporation N2750w-2G Confidential - Do Not Copy...
Page 41
If the test result shows “Connected,” it means the connection is well. If not (failed), it means the connection has problems. Then you need to check the setup procedure or reboot the PC, or simply use another PC to do the firmware upgrade. ViewSonic Corporation N2750w-2G Confidential - Do Not Copy...
1.4 Place the LCD TV into the carton .At last, close the carton and seal it with tape. (Figure 4) 1.Power Cord 2.VGA Cable 3.M/F Cable 4.RCA Cable 5.User’s Guide 6.Remote contrl 7.Guarant Card 8.Battery Figure 3 Figure 4 ViewSonic Corporation N2750w-2G Confidential - Do Not Copy...
Page 43
PACKING PART LIST ( N2750W-2G ) ViewSonic Model Number: VS11404-1G Rev: 1.0 Item ViewSonic P/N Ref. P/N Description Q'ty N2750W(2G) monitor 2013054003P POLYETHY BAG 2012198300P JC278 EPS TOP 2012198600P JC278 EPS MID 2012198500P JC278 EPS DOWN P-00008064 2013228807P POLYETHY BAG...
Page 44
Disassembly Procedure Disassembly of Stand and Dust Cover from LCD TV. 1.1 Detach Dust Cover from the LCD TV and Unscrew 4 screws that secure Stand Unit. Dust Cover Dust Cover Stand ViewSonic Corporation N2750w-2G Confidential - Do Not Copy...
Page 45
2.1 Unscrew 8 screws to remove Rear Cover. Rear Cover 3. Disassembly of Main Board,Power Board,IR Board,Speaker,Front Cover and Panel Unit. 3.1 Unscrew 14 screws to remove Shield Plate and dust cover. ViewSonic Corporation N2750w-2G Confidential - Do Not Copy...
Page 46
Shield Plate 3.2. Unscrew 4 screws to remove Speaker. Speaker 3.3. Unscrew 10 screws to remove Bracket.Fix. ViewSonic Corporation N2750w-2G Confidential - Do Not Copy...
Page 47
3.4. Unscrew 15 screws to remove METAL FITTG-IO. METAL FITTG-I/O-Down ViewSonic Corporation N2750w-2G Confidential - Do Not Copy...
Page 48
METAL FITTG-I/O-Side 3.5. Unscrew 5 screws and disconnect the wires to remove Main Board. Main Board ViewSonic Corporation N2750w-2G Confidential - Do Not Copy...
Page 49
3.6. Unscrew 4 screws and disconnect the wires to remove Power Board. Power Board 3.7. Unscrew 2 screws to remove Front Cover. ViewSonic Corporation N2750w-2G Confidential - Do Not Copy...
Page 50
3.8. Lay Panel Unit facedown and unscrew 9 screws on its right,left,up and down sides, to remove Panel Unit and Panel Bracket. Panel Bracket Panel Unit ViewSonic Corporation N2750w-2G Confidential - Do Not Copy...
Page 53
6.3. NO DISPLAY S-VIDEO TV model SCART SCART1 Check I205 pin 2,4 C259 Check Check Check Check I501 pin 12 has Check I203 pin 27 has Check Check Replace I501 I204 pin 2,6 has I203 pin 26,34 has C272,C273,R245,R246, signal? signal I207 pin 27 I204 pin 2,4 L502...
Page 54
Check I301 if RST pin81 have reset pulse I301 set reset pusle? Change I301 Check I103 crystal 14.318MHZ if working? Check P401 data bus have signal Check panel power 5v Change LCD panel ViewSonic Corporation N2750w-2G Confidential - Do Not Copy...
Remark 2: All revised RSPLs with newly added items or any change made should be highlighted and correlated with the ECN/ECR approved by ViewSonic Corporation. This is to eliminate repeated cross checks of each item between this version and prior versions.
Page 78
BOM LIST (N2750w-2G) ViewSonic Model Number: VS11404- Rev: 1a Serial No. Prefix: QBS Item ViewSonic P/N STATUS Ref. P/N Description Location Universal number# Q'ty PL-00003417 Active 2028258801P STAND JC278UB ABS 94HB PS-7604B 5B04 P-00008114 Active 2012180002P POLYFOAM JC278UB&EC 65E EPE DOWN...
Page 79
Item ViewSonic P/N STATUS Ref. P/N Description Location Universal number# Q'ty 2346110496P CAP,CHIP 125'C CS 0603/X7R/50V 0.1u K T C313 2346110496P CAP,CHIP 125'C CS 0603/X7R/50V 0.1u K T C314 2346110496P CAP,CHIP 125'C CS 0603/X7R/50V 0.1u K T C315 2346110496P CAP,CHIP 125'C CS 0603/X7R/50V 0.1u K T...
Page 80
Item ViewSonic P/N STATUS Ref. P/N Description Location Universal number# Q'ty 2346110496P CAP,CHIP 125'C CS 0603/X7R/50V 0.1u K T C557 2349900996P CAP,CHIP SPEC 0603V-PORT 10P+-10% INPAQ C560 2341120096P CAP,CHIP 125'C CS 0603/COG/50V 20p J T C600 2346733496P CAP,CHIP 85'C CS 0603/Y5V/16V 0.33u Z T...
Page 86
Item ViewSonic P/N STATUS Ref. P/N Description Location Universal number# Q'ty Inactive 2253210096P RES CHIP 1/10W RC 0603 1/10W 10 ohm J T R132 Inactive 2253233296P RES CHIP 1/10W RC 0603 1/10W 3.3Kohm J T R134 Inactive 2253233296P RES CHIP 1/10W RC 0603 1/10W 3.3Kohm J T...
Page 87
M4X10(BND T+) 5B09 M-MS-0808-6354 Active 2404301105P CONNECTOR JST PH 6P SIDE P=2.0 OR EQUAL P711 M-LB-0813-0984 Active 2002201323P DISPLAY CARD VIEWSONIC CRT QUALIFIED LABEL 6P09 M-LB-0813-0959 Active 2055613392P LABEL VSC HIGH VOLTAGE WARNING LABEL 6P14 M-LB-0813-0863 Active 2056606010P SERIAL LABEL...
Page 88
Item ViewSonic P/N STATUS Ref. P/N Description Location Universal number# Q'ty E-R-0405-6600 Active 2253200096P RES CHIP 1/10W RC 0603 1/10W 0 ohm J T R308 E-R-0405-6600 Active 2253200096P RES CHIP 1/10W RC 0603 1/10W 0 ohm J T R311 E-R-0405-6600...
Page 89
Item ViewSonic P/N STATUS Ref. P/N Description Location Universal number# Q'ty E-Q-0402-1608 Active 2360300896P XISTOR,NPN R SMD MMBT3904K SOT-23 FAIRCHILD Q202 E-Q-0402-1608 Active 2360300896P XISTOR,NPN R SMD MMBT3904K SOT-23 FAIRCHILD Q206 E-Q-0402-1608 Active 2360300896P XISTOR,NPN R SMD MMBT3904K SOT-23 FAIRCHILD...
Page 90
APEC I901 1040 DC-00008112 Active 2002310592P GUARANT CARD VIEWSONIC N2750W-2G QSG 6P81 1041 DC-00008111 Active 2001131610P OWNER GUIDE N2750W-2G VS11404-1G CHINA 6P80 1042 CB-00008036 Active 2427751802P CABLE RG59U (M/F) L=1.83M BLACK P952 1043 CB-00003425 Active 2427701893P CABLE RCA 3P(Y/R/W) 2562#26 1.8M BLK...
Company: Add: Tel: Fax: E-mail: After completing this form, please return it to ViewSonic Quality Assurance in the USA at facsimile 1-909-839-7943. You may also e-mail any suggestions to the Director, Quality Systems & Processes (marc.maupin@viewsonic.com) ViewSonic Corporation N2750w-2G Confidential - Do Not Copy...