Track Settings For Eq, Pan; Track Parameters - Zoom R16 Operation Manual

Mixing
Track settings for EQ, pan and send-return level
This track mixer uses track parameters to adjust PAN (stereo position), EQ (equalizer) and SEND-
RETURN EFFECT of the recorder's audio tracks.
1
Press [PAN/EQ].
Track
T r a c k 1
E Q H I G = 0 d B Parameter
Type (EQ is on)
2
Select a track.
Change track number
T r a c k 1
E Q H I G = 0 d B
Turn ON/OFF and select
3
types and values.
Turn setting off.
T r a c k 3
E Q H I G = 0 d B
EQ is ON
Press [ENTER].
T r a c k 3
E Q H I O f f
Parameter ON/
EQ is OFF.
Change the parameter type.
T r a c k 3
E Q H I G = 0 d B
T r a c k 3 P A N = R 2
Change the
parameter type.
Adjust the value of the parameter.
T r a c k 3
E Q H I G = 0 d B
Adjust the value
of the parameter.
4
Press [ENTER] to confirm settings.
37
HINT
• Using the track mixer, you can adjust each track
element (track parameter), including PAN and
the SEND-RETURN EFFECT settings to change
the signal processing track by track.
• At step 2, tracks can be selected using track
status keys. Track indicators light orange when
the track is selected.
NOTE
• The parameters of the L/R channels in stereo
tracks are the same except the phase setting
(INVERT).
• The settings are stored with the project.
• The MASTER TRACK does not have any settings
except for volume control with its fader.
OFF.
Mixing

Track parameters

Parameters available to each track
Setting range:
Display Parameter
Initial value
Adjusts a track's PAN. In case of a stereo track
L100~
PAN adjusts the volume balance between the left and
PAN
R100
right tracks.
EQ HI EQ boost for high pitch/frequency range
−12~ Adjust amount of boost/cut of high frequencies by
EQ HI G EQ HI GAIN* +12dB -12 ~ +12 dB. This parameter is shown only when
:0dB EQ HI is on.
500(Hz)~
EQ HI Adjust EQ boost/cut frequency of high frequencies.
EQ HI F 18(kHz)
FREQUENCY* This parameter is shown only when EQ HI is on.
:8.0(kHz)
EQ MID EQ boost for middle pitch/frequency range
−12~ Adjust amount of boost/cut of medium frequencies
EQ MID G EQ MID GAIN* +12dB by -12 ~ +12 dB. This parameter is shown only
:0dB when EQ MID is on.
40(Hz)~ Adjust EQ boost/cut frequency of medium
EQ MID
EQ MID F 18(kHz) frequencies. This parameter is shown only when
FREQUENCY*
:1..0(kHz) EQ MID is on.
Adjust the Q value (width of the frequency band
EQ MID 0.1~1.0
EQ MID Q affected) of medium frequencies. This parameter is
Q-FACTOR* :0.5
shown only when EQ MID is on.
EQ LOW EQ boost for low pitch/frequency range
−12~ Adjust amount of boost/cut of low frequencies by
EQ LOW GAIN* +12dB -12 ~+12dB. This parameter is shown only when
EQ LO G
:0dB EQ LO is on.
40(Hz)~
EQ LOW Adjust EQ boost/cut frequency of low frequencies .
EQ LO F 1.6(kHz)
FREQUENCY* This parameter is shown only when EQ LO is on.
:125(Hz)
SEND-RETURN EFFECT levels
REVERB REVERB 0~100 Adjust the signal level sent from tracks to the
SEND SEND LEVEL* :0 Reverb effect.
CHORUS/
CHORUS 0~100 Adjust the signal level sent from tracks to the
DELAY SEND
:0 Chorus/Delay effect.
SEND
LEVEL*
0~127
FADER FADER Adjust the sound volume.
:0
On/Off Switch on/off to set the stereo link function that
ST LINK STEREO LINK
:Off connects 2 monaural tracks together. (→P.20)
On/Off Set whether the phase of a track is inverted or not.
INVERT INVERT
:Off Off: normal phase, ON: inverted phase.
Monaural tracks: 1 ~16
Stereo tracks: 1/2 ~ 15/16
Monaural Stereo Master
Explanation
tracks tracks track
*Switch parameters with asterisks (*) On/Off using the ENTER key.
38