Tool - Zoom R16 Operation Manual

Tool

Tuner
The R16 has a multifunctional tuner that includes, for example, chromatic tuning that detects note
names by semitones, standard guitar/bass tuning and half-step-down tuning.
1
Press [TOOL].
2
Press [PLAY/
MUTE/REC] 1-2
times until the red
light turns on.
Red light on:
recording enabled
3
Select >TUNER .
Menu select
T O O L
> T U N E R
Press [ENTER].
4
Select the type of tuner.
C H R O M A T I C 4 4 0 H z
Tuner type
Standard pitch
Tuner type
Change the
standard pitch
G U I T A R 4 4 0 H z
Tuner type
E S t r i n g 6
String note name
Chromatic tuner
TOOL>TUNER>CHROMATIC
5
C H R O M A T I C 4 4 0 H z
Change the
standard pitch
Change the standard pitch (if
necessary) and begin tuning.
C H R O M A T I C 4 4 0 H z
> > A
The note closest to the input signal is indicated.
This display indicates if the pitch is higher
or lower compared to the note indicated.
Tuner type
String1
String2
String3
String/
String4
note
String5
String6
String7
33
Other tuner types
TOOL>TUNER>GUITER/BASS, etc.
5
Select the tuner type.
G U I T A R 4 4 0 H z
E S t r i n g 6
Change string
Change
number
standard pitch
6
Set the standard pitch and
string number.
Start tuning.
G U I T A R 4 4 0 H z
E S t r i n g 6
Note name: play the open string of the indicated note
and adjust the pitch
select
HINT
Pitch indicator
Low Standard
select
Standard
• The pitch indicator responds to sources input on
tracks with red status lights.
• The standard pitch setting is between 435 Hz and
445 Hz in 1 Hz units. The initial setting is 440 Hz.
• Using the other tuners you can use common half-
step and whole-step down tunings, for example.
• The standard pitch value setting will be stored
separately for each project.
GUITAR BASS OPEN A OPEN D OPEN E OPEN G DADGAD
E G E D E
B D C# A B
G A A F# G#
D E E D E
A B A A B
E E D E
B
Tool
Metronome
This metronome, which includes a pre-count function, allows you to change its volume, tone and
pattern. You can also choose to output the metronome sound only through the headphones.
1
Press [TOOL].
T O O L
> T U N E R
Tuner type
select
2
Select
T O O L
> M E T R O N O M E
Press [ENTER].
These are the standard metronome settings (common).
3
Select each setting MENU.
M E T R O N O M E
> O N / O F F
M E T R O N O M E
> T E M P O
4
Select the settings and setting values.
M E T R O N O M E O N / O F F
P l a y & R E C
Press [ENTER].
High
HINT
Tapping the tempo
• On the TEMPO screen, press the (TOOL) key
several times at the tempo you desire, and the
tempo will be set to the detected median value.
Changing and adjusting the metronome output
[METRONOME] switch: Sets the output
D D
B A
G G
• These settings are stored for each project.
D D
• You can use the metronome even during MASTER
G A
TRACK playback.
D D
MENU settings and setting values
Settings
Change menu
Play Only
REC Only
Play&REC
>METRONOME .
Off (default)
Manual input
Setting range
40.0~250.0
Setting range
Change menu
Setting range
L100–R100
Settings
Change item BELL (default)
COWBELL
HIGH-Q
Settings
0/4 (no accent)
1/4~8/4, 6/8
Settings
SPECIAL
OUTPUT + PHONES
The METRONOME sound is output
through both the OUTPUT and
PHONES jack.
PHONES ONLY NOTE
The metronome sound is output
through only the PHONES jack.
Be aware that the metronome starts sounding
Use the BALANCE knob to adjust the
from the instant that recording/playback begins.
relative volumes of the [MASTER] fader
Therefore, if you begin in the middle of a song, the
signal and the metronome sound.
metronome sound and the pulse of the music might
MASTER CLICK
be out of sync. Moreover, if you turn the metronome
(metronome)
volume up high, the accented beat of some sounds
might become difficult to distinguish.
ON/OFF: Set when active
During playback only
During recording only
During both playback & recording
No metronome sound
TEMPO: Set manually or by number
Input the tempo by tapping the
[TOOL] key repeatedly
Initial value: 120.0
LEVEL: Change metronome volume
0–100 Initial value: 50
PAN: Stereo position
Initial value: C (center)
SOUND: Change tone
Metronome sound with a bell on the
accent
CLICK Click sound only
STICK Drum stick sound
Cowbell tone
Synthesized click sound
PATTERN: Change rhythm
Initial value: 4/4
PRE-COUNT: Pre-count setting
Off No sound
Enable sound during pre-count for 1
1~8
to 8 beats. Initial: 4 beats
Special (rhythm shown below)
Metronome indicator
During metronome use the metronome
indicator lights in time with the tempo.
34