Remote Control - Pioneer VSX-D510 Service Manual

VSX-D510

Remote Control

MULTI CONTROL
DVD/LD TV/SAT VCR/DVR
1
RECEIVER TUNER
2
2
DSP MODE MIDNIGHT 5.1CH
1
CHANNEL TEST
SELECT TONE
3
5
CHANNEL
LEVEL
9
FUNC
4
TV CONTROL
VOL
ST
5
MENU
SOURCE CLASS
6
D.ACCESS
7
LOUDNESS FUNCTION MUTING
8
FL
9
RECEIVER
DIMMER
0
AUDIO/VIDEO PRE-PROGRAMMED
REMOTE CONTROL UNIT
-
1 MULTI CONTROL buttons
Use to put the receiver/remote control in the stated mode.
For other equipment controls, see Controlling the Rest of Your
System on .
2 RECEIVER button
Use this button when setting up the surround sound for the
receiver.
3 NUMBER/MODE buttons
Use the number buttons to select the radio frequency in tuner
DIRECT ACCESS mode or the tracks in CD, DVD mode etc.
Also, buttons marked with the following names have special
functions. If you try to use one of these functions but the
display flashes it means that function cannot be used in the
current mode (for example DSP modes cannot be used when
5.1 CH setting is on).
2
Use to put receiver in DOLBY DIGITAL, DOLBY SURROUND
and DTS modes. To use first press the
operate this button.
DSP MODE
Use to put receiver in one of the DSP modes. To use first press
the button then operate this button.
RECEIVER
58
=
Î
CD
CD-R/
TV CONT
TAPE/MD
2 3 4
SIGNAL
ATT
SELECT
6 7 8
EFFECT
~
0
10 DISC
CH
VOL
FQ
!
ST
ENTER
TOP
MENU
@
FQ
MPX BAND
CHANNEL
#
DISPLAY RF ATT
$
%
REMOTE MASTER
SETUP VOLUME
^
RECEIVER button then
MIDNIGHT
Use to put receiver in MIDNIGHT mode. To use first press the
button then operate this button.
RECEIVER
5.1 ch
When the DVD/LD or DVD 5.1 CH function is selected each
press switches the DVD/LD input between DVD/LD and DVD
5.1 CH. To use first press the
this button.
CHANNEL SELECT
Use to select a speaker when setting up the surround sound of
the receiver. To use first press the
operate this button.
TEST TONE
Use to sound the TEST TONE when setting up the surround
sound of the receiver. To use first press the
then operate this button.
ATT
If the Overload indicator lights often, use to attenuate (lower)
the level of an analog input signal to prevent distortion. To use,
press the button first, then press this button.
RECEIVER
CHANNEL LEVEL +/–
Use to set up the levels of the surround sound of the receiver.
To use first press the
RECEIVER
button.
SIGNAL SELECT
Use to select the proper signal (analog, digital) for the source
your are inputting. To use first press the
then operate this button.
4 THE FOLLOWING FOUR SETS OF BUTTONS ARE
DEDICATED TV CONTROL. THEY ARE ONLY USED FOR
CONTROLLING YOUR TV.
TV FUNC button
Use select the TV function.
TV (POWER) button
Use to turn on the power of the TV.
TV CH +/– buttons
Use to change channels on your TV.
TV VOL +/– buttons
Use to adjust the volume on your TV.
5 MENU button
Use to access different menus associated with your DVD player.
To use first press the
DVD/LD
6 SOURCE button
Use to turn on/off the components connected to the receiver.
To use first press the
MULTI CONTROL
this button.
7 THE FOLLOWING BUTTONS ARE BOTH CONTROLS
FOR OTHER COMPONENTS (LIKE A DVD PLAYER)
AND DEDICATED TUNER CONTROLS. THE TUNER
CONTROLS ARE EXPLAINED HERE. YOU CAN USE
THEM AFTER YOU HAVE PUSHED THE TUNER MULTI
CONTROL BUTTON.
CLASS button
Use to switch between the three banks (classes) of station
memories.
MPX button
Use to switch between auto stereo and mono reception of FM
broadcasts. If the signal is weak then switching to MONO will
improve the sound quality. Also, this is the pause button for
CDs, tapes, DVDs, etc.
button then operate
RECEIVER
RECEIVER button then
button
RECEIVER
button then operate this
button
RECEIVER
button then operate this button.
buttons then operate