Page 2
LBO-HDMI-AD User’s Manual Link Bridge Fiber Optic HDMI Video Converting Transmitter System SAFETY INSTRUCTIONS AND COMPLIANCE DECLARATIONS PLEASE OBSERVE THE FOLLOWING SAFETY PRECAUTIONS AS OUR PRODUCTS CONTAIN CLASS I LASER PRODUCTS WARNING Do not disconnect the fiber optic connector while the unit is powered up.
(1920x1200 @ 60Hz) or 720p/1080i/1080p HDTV video resolution. DVI video is also available through a DVI-to-HDMI adapter cable. No user adjustment is required for the LBO-HDMI-AD system due to the use of advanced digital fiber optic transmission system technology with zero compression and zero bit reduction.
Page 5
Audio Out HDMI In Audio In Data Power/Optical Link LED Data Audio Out HDMI OUT Audio In Figure 1-1 LBO-HDMI-AD-T/R Front Panel REAR PANEL (STANDALONE) Fiber Optic Output Connector Power Connector Figure 1-2 LBO-HDMI-AD-T/R Rear Panel Broadata Technical Support, (800) 214-0222...
Page 6
LBO-HDMI-AD User’s Manual Link Bridge Fiber Optic HDMI Video Converting Transmitter System FRONT PANEL (WALL PLATE) Power/Optical Power/Optical Link LED Link LED Audio Audio HDMI In HDMI Out Audio Audio Data Data Data Data Figure 1-3 LBO-HDMI-AD-T/R-WP Front Panel REAR PANEL (WALL PLATE)
LBO-HDMI-AD-T (or LBO-HDMI-AD-R) is a transmitter or receiver and they can be paired with any DVI/HDMI centric LBO receiver (such as LBO-DVI-R). One LBO-HDMI-AD-T transmitter unit is located at the near- end and connected through one optical fiber, to the LBO-HDMI-AD-R receiver located at the far-end of the link.
1. Connect the LBO-HDMI-AD-T (Transmitter) unit’s to HDMI video input port to the user’s HDMI video source with the appropriate HDMI cables. 2. For the receive unit, connect the LBO-HDMI-AD-R (Receiver) HDMI video output ports to the user’s HDMI video receivers with the appropriate HDMI cables respectively, as illustrated in Figure 2-2.
“AUDIO INPUT” connector of the line level audio receiver. On the LBO-HDMI-AD unit, connect the other end of the cables to the front panel stereo jack connector labeled “AUDIO OUT” (see Figure 2-3b).
Link Bridge Fiber Optic HDMI Video Converting Transmitter System 2.2.1.3 Serial Data Interface Each LBO-HDMI-AD unit can be used for RS-232 interface. RS-232 data The LBO-HDMI-AD transmits two channels of data signals. Follow the procedures for installing data terminal devices.
2. Prior to connecting the fiber optic cables, remove and save the dust caps from the optical port of the LBO-HDMI-AD units. Clean the fiber optic connector and use a lint-free cloth dampened with alcohol to thoroughly wipe the side and end of the ferrule.
Page 12
LBO-HDMI-AD User’s Manual Link Bridge Fiber Optic HDMI Video Converting Transmitter System LBO-HDMI-AD-T LBO-HDMI-AD-R LBO-HDMI-AD-T-WP LBO-HDMI-AD-R-WP Figure 2-5 Fiber Optic Connection Broadata Technical Support, CustomerService@Broadatacom.com...
Fiber Optic HDMI Video ConvertingTransmitter System 2.3 DC Power Connection Congratulations! You are now ready to power up the LBO-HDMI-AD and set up your network connection. In order to make sure that you have a proper installation, please observe the following: 1.
Fiber Optic HDMI Video Converting Transmitter System 2.4 In-Wall Power/Fiber Wiring Instruction The in-wall power/fiber installation for the LBO-HDMI-AD-WP (wall plate version) must confirm national and local electrical codes, e.g., UL junction boxes shall be used and DC power source shall not exceed product rated range (+12VDC @ 1.5A).
Page 15
Fiber Optic HDMI Video ConvertingTransmitter System Wall Clamp Junction Box LBO-HDMI-AD-WP Unit Power Wire +12V CHASSIS Fiber Cable Link Port Figure 2-6 In-wall fiber/power cable installation Captive Screw Connector +12V GND CHASSIS Figure 2-7 Power Connection Broadata Technical Support, (800) 214-0222...
Page 16
LBO-HDMI-AD User’s Manual Link Bridge Fiber Optic HDMI Video Converting Transmitter System Note 1: During installation, the installer may need to connect the power supply output to an appropriate Listed NEC type cable before it is routed behind a wall. Simply routing the power supply output cable behind a wall will most likely not comply with applicable installation requirements.
Fiber Optic HDMI Video ConvertingTransmitter System 3.0 OPERATION After the installation procedure is completed, the units are ready for operation. To operate the LBO-HDMI-AD units, simply apply power as indicated in the previous sections. The following describes the LED activity.
However, observe the following light indicators to make sure that the unit is working properly: 4.2 Troubleshooting If the LBO-HDMI-AD units do not operate properly after installation, check for: possible cable breaks, loose connections, and incorrect cable connections. If a problem exists on the fiber link, please check your fiber connectors for improperly cleaned fiber cables and connectors.
Page 19
Both ends of the link are connected to the corresponding equipment and to the same corresponding channel port. c. Cable connections at both the video/audio channels are securely fastened to each connector. Turn the power off, then back on to reset the link. Broadata Technical Support, (800) 214-0222...
U.S. Please call Customer Service at 800-214-0222 for information. 6.2 Return/Repair Service The LBO-HDMI-AD System contains no user serviceable components. If you have a problem with your unit, please contact the Customer Service Department. To facilitate our return/repair processing please contact Broadata Communications, Inc.
Fiber Optic HDMI Video ConvertingTransmitter System 7.0 LIMITED WARRANTY Broadata Communications, Inc. (BCI) warrants, for a period of one year from date of shipment, each product sold shall be free from defects in material and workmanship. BCI will correct, either by repair, or at BCI’s...
Page 24
LBO-HDMI-AD User’s Manual Link Bridge Fiber Optic HDMI Video Converting Transmitter System Broadata Technical Support, CustomerService@Broadatacom.com...
Page 25
LBO-HDMI-AD User’s Manual Link Bridge Fiber Optic HDMI Video ConvertingTransmitter System Broadata Technical Support, (800) 214-0222...
Page 26
Broadata Communications, Inc. 2545 West 237th Street, Suite K Torrance, CA 90505 1-800-214-0222 (310) 530-1416 (310) 530-5958 (Facsimile) e-mail: CustomerService@Broadatacom.com Website: www.broadatacom.com 60000-LBOHDMI/AD...