Talk Time; Lock Out Count - PACH & COMPANY AeGIS 4000 Installation And Programming Manual

Function Local Programming
the door is already unlocked you will
hear "One Short Beep" or
• Enter 0 to Lock and you will hear
"One Long Beep" then "One Short
Beep".
Step 5
to program another parameter other-
wise press ∗ to exit and you will hear
"Three Short Beeps".
Step 1
Mode: Press 0 and # simultaneously
then release. If you are in the
programming mode, proceed to step 2.
Step 2
Code (factory default is 0000) and you
will hear "One Short Beep". If you
entered an invalid master
you will hear "One Long Beep",
repeat step 1. Should your master
92
code become lost or forgotten see
Reset Master Code.

TALK TIME

(10-90 seconds)
Step 3
hear "One Short Beep".
THE SYSTEM
WILL BE
DISCONNECTED
Step 4
ACCORDING TO
(10 – 90 seconds) then press #, you
THE TALK TIME
will hear "One Short Beep".
PROGRAMMED.
Step 5
to program another parameter other-
wise press ∗ to exit and you will hear
"Three Short Beeps".
Step 1
Mode: Press 0 and # simultaneously
then release. If you are in the pro-
gramming mode, proceed to step 2.
93
Step 2
Code (factory default is 0000) and you
LOCK OUT
will hear "One Short Beep". If you
COUNT
entered an invalid master code you will
(03-09)
hear "One Long Beep", repeat
THE SYSTEM
step 1. Should your master code
WILL BE
become lost or forgotten see Reset
DISABLED FOR
Master Code.
50 SECONDS
AFTER INVALID
Step 3
CODES HAVE
hear "One Short Beep".
BEEN ENTERED
ACCORDING TO
THE NUMBER
Step 4
OF LOCKOUT
value (3-9) then press #, you will hear
COUNT
"One Short Beep".
PROGRAMMED.
Step 5
to program another parame
wise press ∗ to exit and you will
"Three Short Beeps".
Pach and Company
AeGIS 4000
Enter another Function Code
Entering The Programming
Enter the 4-digit Master
code
Enter 92 then #, you will
Enter the talk-time value
Enter another Function Code
Entering The Programming
Enter the 4-digit Master
Enter 93 then #, you will
Enter a new lockout count
Enter another Function Code
ter
other-
hear
Premise Phone
Step 6 Enter another function code
to program a different parameter or
exit the program by pressing ∗ ∗ and
you will hear "Three Short Beeps".
Step 1 Pick up the phone and wait
for a dial tone.
Step 2 Press # # and you will hear
"One Short Beep".
Step 3 Press # and you will hear
"One Short Beep".
Step 4 Enter the Function Code 92
then press #, you will hear "One Short
Beep".
Step 5 Enter the talk time value
(10 –90 seconds) then press #, you
will hear "One Short Beep".
Step 6 Enter another function code
to program a different parameter or
exit the program by pressing ∗ ∗ and
you will hear "Three Short Beeps".
Step 1 Pick up the phone and wait
for a dial tone.
Step 2 Press # # and you will hear
"One Short Beep".
Step 3 Press # and you will hear
"One Short Beep".
Step 4 Enter the Function Code 93
then press #, you will hear "One Short
Beep".
Step 5 Enter the lockout count
(03 – 09) then press #, you will hear
"One Short Beep".
Step 6 Enter another function code
to program a different parameter or
exit the program by pressing ∗ ∗ and
you will hear "Three Short Beeps".
Page 17
Chapter 3. Programming
Remote Phone
then "One Short Beep". If you hear
"One Short Beep", means the door
is already unlocked or
•
Press 0 (to lock) then press #, you
will hear "One Long Beep" then
"One Short Beep".
Step 5 Enter another function code
to program a different parameter or
exit the program by pressing ∗ ∗ and
you will hear "Three Short Beeps".
Step 1 Call to the AeGIS 4000
system (you must know the system's
phone number), you will hear: "One
Short Beep", the gate is locked. "Two
Short Beeps", the gate is unlocked.
Step 2 Press # then enter a valid
master code and you will hear:
• "One Short Beep", the master code
is accepted then press # and you will
hear "One Short Beep".
• "One Long Beep", the master code
is rejected and the connection will be
disconnected.
Step 3 Enter the Function Code 92
then press #, you will hear "One Short
Beep".
Step 4 Enter the talk time value
(10 –90 seconds) then press #, you
will hear "One Short Beep".
Step 5 Enter another function code
to program a different parameter or
exit the program by pressing ∗ ∗ and
you will hear "Three Short Beeps"
Step 1 Call to the AeGIS 4000
system (you must know the system's
phone number), you will hear: "One
Short Beep", the gate is locked. "Two
Short Beeps", the gate is unlocked.
Step 2 Press # then enter a valid
master code and you will hear:
• "One Short Beep", the master code
is accepted then press # and you
will hear "One Short Beep".
• "One Long Beep", the master code
is rejected and the connection will be
disconnected.
Step 3 Enter the Function Code 93
then press #, you will hear "One Short
Beep".
Step 4 Enter the lockout count
(03 – 09) then press #, you will hear
"One Short Beep".
.