Delete Or Overwrite Individual Access Code; Relay 1 (Door 1) Open Interval - PACH & COMPANY AeGIS 4000 Installation And Programming Manual

Function Local Programming
Step 1
Delete or
Mode: Press 0 and # simultaneously
overwrite
then release. If you are in the
Individual
programming mode, proceed to step 2.
Access Code
Step 2
Code (factory default is 0000) and you
will hear "One Short Beep". If you
entered an invalid master code you will
hear "One Long Beep", repeat
step 1. Should your master code
become lost or forgotten see Reset
Master Code.
Step 3
(01 – 50) where you stored the access
code to be deleted.
• "Two Long Beeps" if the Index
Number has an associated access
code, proceed to step 4.
• "No Beep" if the Index Number has
no associated access code and
press "∗" and repeat this step.
Step 4
• 0 then # to delete the access code,
you will hear "One Short Beep" or
• 1 then #, you will hear "No Beep"
and enter the new access code and
you will hear "One Short Beep".
Step 5
another access code or enter another
Function Code to program another
parameter, otherwise press ∗ to exit
and you will hear "Three Short
Beeps".
Step 1
Mode: Press 0 and # simultaneously
then release. If you are in the
programming mode, proceed to step 2.
Step 2
Code (factory default is 0000) and you
will hear "One Short Beep". If you
entered an invalid master code you will
hear "One Long Beep", repeat
step 1. Should your master code
51
become lost or forgotten see Reset
Master Code.
RELAY 1
(DOOR 1) OPEN
INTERVAL
Step 3
(01-90 seconds)
hear "One Short Beep".
Step 4
value (01 – 90 seconds) then press #,
you will hear "One Short Beep".
Step 5
to program another parameter
hear "Three Short Beeps".
Pach and Company
AeGIS 4000
Entering The Programming
Enter the 4-digit Master
Enter the Index Number
Enter
Return to step 3 to delete
Entering The Programming
Enter the 4-digit Master
Enter 51 then #, you will
Enter door 1 open interval
Enter another Function Code
Premise Phone
Must delete the individual access
code from the local keypad.
Pick up the phone and wait for a dial
tone.
Step 2 Press # # and you will hear
"One Short Beep".
Step 3 Press # and you will hear
"One Short Beep".
Step 4 Enter the Function Code 51
then press #, you will hear "One Short
Beep".
Step 5 Enter door open interval
(01 – 90 seconds) then press #, you
will hear "One Short Beep".
Step 6 Enter another function code
to program a different parameter or
exit the program by pressing ∗ ∗ and
you will hear "Three
Short Beeps".
Page 10
Chapter 3. Programming
Remote Phone
Must delete the individual access
code from the local keypad.
Step 1 Call to the AeGIS 4000
system (you must know the system's
phone number), you will hear: "One
Short Beep", the gate is locked. "Two
Short Beeps", the gate is unlocked.
Step 2 Press # then enter a valid
master code and you will hear:
• "One Short Beep", the master code
is accepted then press # and you will
hear "One Short Beep".
• "One Long Beep", the master code
is rejected and the connection will be
disconnected.
Step 3 Enter the Function Code 51
then press #, you will hear "One Short
Beep".
Step 4 Enter door open interval
(01 – 90 seconds) then press #, you
will hear "One Short Beep".
Step 5 Enter another function
to program a different parameter or
exit the program by pressing ∗ ∗ and
you will hear "Three Short Beeps".
code