Program Direct Call Forwarding; Delete Direct Call Forwarding - PACH & COMPANY AeGIS 4000 Installation And Programming Manual

Function Local Programming
Step 1
Mode: Press 0 and # simultaneously
then release. If you are in the
programming mode, proceed to step 2.
Step 2
Code (factory default is 0000) and you
will hear "One Short Beep". If you
entered an invalid master code you will
hear "One Long Beep", repeat step
1. Should your master code become
lost or forgotten see Reset Master
Code.
Step 3
hear "One Short Beep".
Step 4
to program another parameter; other-
wise press ∗ to exit and you will hear
"Three Short Beeps".
Step 1
Program
Mode: Press 0 and # simultaneously
Direct Call
then release. If you are in the
Forwarding
programming mode, proceed to step 2.
Step 2
70 Code (factory default is 0000) and you
will hear "One Short Beep". If you
DIRECT CALL
entered an invalid master code you will
FORWARDING
hear "One Long Beep", repeat
step 1. Should your master code
IS USED IF
become lost or forgotten Reset Master
A DEDICATED
Code.
PHONE LINE IS
USED OR IF
YOU WANT TO
Step 3
FORWARD THE
hear "No Beep".
CALL
MANUALLY.
Step 4
want to forward the call up to 11-digit
NOTE:
then press #, you will hear "One Short
INTERCOM
MODE IS Beep".
DISABLED IF
A PHONE
Step 5
NUMBER IS
to program another parameter; other-
PROGRAMMED
wise press ∗ to exit and you will hear
ON FUNCTION
"Three Short Beeps".
CODE 70
Step 1
Delete Direct
simultaneously then release.
Call
Forwarding
Step 2
telephone number, you will hear
"Three Short Beeps". Now, the
AeGIS 4000 is reset to "Intercom
Mode".
Pach and Company
AeGIS 4000
Entering The Programming
Enter the 4-digit Master
Enter 65 then #, you will
Enter another Function Code
Entering The Programming
Enter the 4-digit Master
Enter 70 then #, you will
Enter the phone number you
Enter another Function Code
Press 0 and ∗
Press 0 then # to delete
Premise Phone
Step 3 Press # and you will hear
"One Short Beep".
Step 4 Enter 65 then press #, you
will hear "One Short Beep".
Step 5 Enter another function code
to program different parameter or exit
the program by pressing ∗ ∗ and you
will hear "Three Short Beeps".
Step 1 Pick up the phone and wait
for dial tone.
Step 2 Press # # and you will hear
"One Short Beep".
Step 3 Press # and you will hear
"One Short Beep".
Step 4 Enter 70 then press #, you
will hear "No Beep".
Step 5 Enter the non-indexed call
forwarding phone number up to 11-
digit you will hear "One Short Beep".
Step 6 Enter another function code
to program a different parameter or
exit the program by pressing ∗ ∗ and
you will hear "Three
eeps".
Short B
Step 1 Pick up the phone and wait
for dial tone.
Step 2 Press # # and you will hear
"One Short Beep".
Step 3 Press 6 and you will hear
"Three Short Beeps", and the system
disconnects the call.
Page 12
Chapter 3. Programming
Remote Phone
Step 2 Press # then enter a valid
master code and you will hear:
• "One Short Beep", the master code
is accepted then press # and you will
hear "One Short Beep" .
• "One Long Beep", the master code
is rejected and the connection will be
disconnected.
Step 3 Press # to enter into the
programming mode and you will hear
"One Short Beep" or ∗∗ to hang-up
the call.
Step 4 Enter 65 then press #, you
will hear "One Short Beep".
Step 5 Enter another function code
to program different parameter or exit
the program by pressing ∗ ∗ and you
will hear "Three Short Beeps".
Step 1 Call to the AeGIS 4000
system (you must know the system's
phone number), you will hear: "One
Short Beep", the gate is locked."Two
Short Beeps", the gate is unlocked.
Step 2 Press # then enter a valid
master code and you will hear:
• "One Short Beep", the master code
is accepted then press # and you will
hear "One Short Beep" .
• "One Long Beep", the master code
the connection will
is rejected and
be disconnected.
Step 3 Press # to enter into the
programming mode and you will hear
"One Short Beep" or ∗∗ to hang-up
the call.
Step 4 Enter 70 then press #, you
will hear "No Beep".
Step 5 Enter the non-indexed call
forwarding phone number up to 11-
digit you will hear "One Short Beep".
Step 6 Enter another function code
to program a different parameter or
exit the program by pressing ∗ ∗ and
you will hear "Three Short Beeps.
Step 1 Call to the AeGIS 4000
system (you must know the system's
phone number), you will hear: "One
Short Beep", the gate is locked. "Two
Short Beeps", the gate is unlocked.
Step 2 Press # then enter a valid
master code and you will hear:
• "One Short Beep", the master code
is accepted then press # and you will
hear "One Short Beep".