Page 1 Chinese Model East European Model North European Model Russian Model Photo: CCD-TRV77E CCD-TRV66E RMT-717 B501 MECHANISM For MECHANISM ADJUSTMENT, refer to Note : Specifications of CCD-TRV66E are described. the “8mm Video MECHANICAL ADJUSTMENT MANUAL ” (9-973-801-11). SPECIFICATIONS VIDEO CAMERA RECORDER MICROFILM...
Page 2 6 A/V connecting cable (1) 7 Shoulder strap (1) 8 2-pin conversion adaptor (1) CCD-TRV66E : E, HK 9 21-pin conversion connector (1) CCD-TRV66E : AEP, EE, NE, RU, UK/CCD-TRV77E • Abbreviation : Hong Kong Model : Australian Model SAFETY-RELATED COMPONENT WARNING!!
Page 3: Table Of Contents
TABLE OF CONTENTS SERVICE NOTE 2-3. Mechanism Deck ····························································· 2-4 2-4. EVF Block, VF-129 Board ·············································· 2-5 POWER SUPPLY DURING REPAIRS ····························· 6 2-5. Lens Block (TRV66E), (TRV77E) ·································· 2-6 TO TAKE OUT A CASSETTE WHEN NOT EJECT 2-6. Mechanism Deck, VC-214, DD-117 Boards ··················· 2-8 (FORCE EJECT) ································································...
Page 4: Repair Parts List
• PD-105 (RGB Decoder, LCD, Timing Generator, D range Adjustment (PD-105 board) ····························· 5-25 Back Light Drive) Bright Adjustment (PD-105 board) ······························· 5-26 Printed Wiring Board ···································· 4-60 Contrast Adjustment (PD-105 board) ···························· 5-26 • PD-105 (RGB Decoder, LCD)(1/2) V-COM Level Adjustment (PD-105 board) ·················· 5-27 Schematic Diagram ·······································...
Page 5 6-1-2. Cabinet (R) Block Assembly ··········································· 6-2 6-1-3. LCD Block Assembly ······················································ 6-3 6-1-4. Cabinet (L) Block and Main Boards Assembly ··············· 6-4 6-1-5. EVF Block Assembly ······················································ 6-5 6-1-6. Cassette Compartment Assembly ···································· 6-6 6-1-7. LS Chassis Assembly ······················································ 6-7 6-1-8.
Page 6: Service Note
SERVICE NOTE POWER SUPPLY DURING REPAIRS In this unit, about 10 seconds after power is supplied (8.4V) to the Battery switch battery terminal using the service power cord (J-6082-223-A), the power is shut off so that the unit cannot operate. This following two methods are available to prevent this.
Page 7: Self-Diagnosis Function
SELF-DIAGNOSIS FUNCTION Self-diagnosis Display Self-diagnosis Function When problems occur while the unit is operating, the counter of the When problems occur while the unit is operating, the self-diagnosis viewfinder or Display window shows a 4-digit display consisting function starts working, and displays on the viewfinder or Display window what to do.
Page 8: Self-Diagnosis Code Table
Self-diagnosis Code Table Self-diagnosis Code Block Detailed Symptom/State Correction Function Code Condensation. Remove the cassette, and insert it again after one hour. Video head is dirty. Clean with the optional cleaning cassette. Non-standard battery is used. Use the InfoLITHIUM battery. LOAD direction.
Page 9 Self-diagnosis Code Block Detailed Symptom/State Correction Function Code Inspect the lens block focus reset sensor (Pin !™ of CN551 of VC- 214 board) when focusing is performed when the control dial is Difficult to adjust focus rotated in the focus manual mode and the focus motor drive circuit (Cannot initialize focus.) (IC552 of VC-214 board) when the focusing is not performed.
Page 10: General
CCD-TRV66E/TRV77E SECTION 1 This section is extracted from instruction GENERAL manual. (CCD-TRV66E model)
Page 19 1-10...
Page 20 1-11...
Page 21 1-12...
Page 22 1-13...
Page 23 1-14...
Page 24 1-15...
Page 25 1-16...
Page 26 1-17...
Page 27 1-18...
Page 28 1-19...
Page 29 1-20...
Page 30 1-21...
Page 31 1-22...
Page 32 1-23...
Page 33 1-24E...
Page 34: Disassembly
CCD-TRV66E/TRV77E SECTION 2 DISASSEMBLY The following flow chart shows the disassembly procedure. 2-1. LCD UNIT, PD-105 board 2-2. CABINET (R) ASSEMBLY MECHANISM DECK check 2-3 MECHANISM DECK (Note) (TRV66E)(TRV77E) service position Note : Use the parts only which can be removed easily from outside of the MECHANISM DECK.
Page 35: Lcd Unit, Pd-105 Board
NOTE: Follow the disassembly procedure in the numerical order given. 2-1. LCD UNIT, PD-105 BOARD 7 P cabinet (C)(93) 8 Two tapping screws (B2 × 8) 6 Claws 4 Two screws (M2 × 4) 3 Rotate it by 90 ° in the direction of the arrow.
Page 36: Cabinet (R) Assembly (Trv66E), (Trv77E)
2-2. CABINET (R) ASSEMBLY (TRV66E) !™ Screw (M2 × 4), lock ace, p2 8 FP-43 flexible !£ Two screws (M2 × 4), - 2 1 board (20P) lock ace, p2 a r d 4 Screw (M2 × 4), lock ace, p2 1 Two screws !¡...
Page 37: Mechanism Deck
2-3. MECHANISM DECK Two screws Remove it in the direction (M2 × 4), of the arrow b . lock ace, p2 3 Screw (M2 × 4), lock ace, p2 2 Cassette lid assembly 9 Jack cover 5 Battery panel (P) Remove it in the direction assembly of the arrow a .
Page 38: Evf Block, Vf-129 Board
2-4. EVF BLOCK, VF-129 BOARD 5 EVF block assembly 9 Finder (S) assembly 8 Rotate it in the direction of 3 FFC-256 the arrow b and remove it flexible flat cable (4P) in the direction of the arrow c . 6 Screw 7 Slide the button in the !∞...
Page 39: Lens Block (Trv66E), (Trv77E)
2-5. LENS BLOCK (TRV66E) 7 Flexible board (from LENS block) (24P) 5 Screw (M2 × 3) 6 Screw (M2 × 3) 3 FP-54 flexible board 8 LENS block 2 VL-23 board 1 Screw (M2 × 3) - 2 1 a r d 4 Screw (M2 ×...
Page 40 [LENS BLOCK CHECK SERVICE POSITION] Adjustment remote commander (RM-95) CPC-7 jig CPC-7 jig (J-6082-382-A) LANC jack Contacting surface DC IN Extension cable (J-6082-357-A) (16P) AC POWER - 2 1 AC IN a r d ADAPTOR LENS BLOCK FP-43 flexible board Cabinet (R) assembly Base (Use box or the like) (Supports the VL-23 board)
Page 41: Mechanism Deck, Vc-214, Dd-117 Boards
2-6. MECHANISM DECK, VC-214, DD-117 BOARDS 5 Screw (M2 × 4), !™ Cabinet (L) assembly Remove it in the direction of the arrow a . lock ace, p2 Remove it in the direction of the arrow b . Remove it gently as a thin flexible board is held by a claw.
Page 42 [MECHANISM DECK, VC-214, DD-117 BOARDS CHECK SERVICE POSITION] Battery panel (P) AC IN assembly Control switch block (SS-8500) AC POWER ADAPTOR Base 2 Adjustment remote DC IN commander (RM-95) DD-117 board Extension cable (TRV77E) (J-6082-439-A) (70P) Control switch block (FK-8500) Mechanism deck Base 1 CPC-7 jig...
Page 43: Video Light (Trv66E)
2-7. VIDEO LIGHT (TRV66E) 3 Halogen lamp 2 Remove the lamp holder in the direction of the arrow a . 1 Remove the claws 2-8. CF-56 BOARD Note : When attaching it. Align the switch position as shown. 5 FFC-256 flexible flat cable (4P) 6 Speaker harness (2P) 7 Five tapping...
Page 44: Circuit Boards Location
2-10.CIRCUIT BOARDS LOCATION (TRV66E) (TRV77E) CD-209 CD-209 (CCD IMAGER) (CCD IMAGER) VF-129 VF-129 (B/W EVF) (B/W EVF) VL-23 (VIDEO LIGHT) DD-117 DD-117 (DC/DC CONVERTER) MA-351 MA-351 (DC/DC CONVERTER) STEREO MIC AMP, STEREO MIC AMP, LASER LINK LASER LINK PJ-92 PJ-92 (AV IN/OUT) (AV IN/OUT) SE-83...
Page 45: Flexible Boards Location
2-11.FLEXIBLE BOARDS LOCATION (TRV66E) (TRV77E) CONTROL SWITCH BLOCK CONTROL SWITCH BLOCK (FK-8500) (FK-8500) FP-46 FP-45 From S/T REEL From S/T REEL SENSOR SENSOR From CAPSTAN From CAPSTAN MOTOR MOTOR From DRUM From DRUM MOTOR MOTOR FP-44 FP-44 From VIDEO From VIDEO HEAD HEAD From LOADING MOTOR,...
Page 46: Block Diagrams
CCD-TRV66E/TRV77E SECTION 3 BLOCK DIAGRAMS 3-1. OVERALL BLOCK DIAGRAM...
Page 47: Camera/Video Block Diagram
CCD-TRV66E/TRV77E 3-2. CAMERA/VIDEO BLOCK DIAGRAM IC1401 7 IC1402 6 IC502 @§ IC001 $¶ IC001 1 CAMERA REC CAMERA REC CAMERA REC IC001 @¶,#¢ CAMERA REC 1.1Vp-p 1.2Vp-p IC202 !§ IC202 !£ 1 µsec/div, 0.1 V/div CAMERA REC CAMERA REC 0.1 µsec/div 0.3Vp-p...
Page 48: Vtr/Camera Control Block Diagram
CCD-TRV66E/TRV77E 3-3. VTR/CAMERA CONTROL BLOCK DIAGRAM IC402 1 20.0 MHz 1.7Vp-p IC402 $¶ 2.8Vp-p 25 Hz 3-10 3-11...
Page 49: Servo Block Diagram
CCD-TRV66E/TRV77E 3-4. SERVO BLOCK DIAGRAM IC801 !• IC802 9 IC801 ^¢ IC801 1,2,@ª 0.1Vp-p 150 Hz 2.8Vp-p 0.75Vp-p 10.3 µsec 2 µsec 1.2Vp-p 150 Hz IC802 7 IC801 !¡ 100mV 1.0 msec/div IC801 4 2.8Vp-p 25 Hz 0.75Vp-p 2 µsec IC402 1 1.7Vp-p...
Page 50: Mode Control Block Diagram
CCD-TRV66E/TRV77E CCD-TRV66E/TRV77E 3-5. MODE CONTROL BLOCK DIAGRAM IC604 $º 3.2Vp-p 20.0 MHz IC604 %£ 3.2Vp-p 32.768 KHz 3-15 3-16 3-17...
Page 51: Audio Block Diagram
CCD-TRV66E/TRV77E 3-6. AUDIO BLOCK DIAGRAM IC751 $¡ IC751 @™ CAMERA REC/PB CAMERA REC/PB IR ON IR ON 0.22Vp-p 0.22Vp-p 0.5 µsec/div IC751 7 CAMERA REC/PB 0.2Vp-p 4.43 MHz 3-19 3-20 3-21 3-22...
Page 52: Lcd Block Diagram
CCD-TRV66E/TRV77E 3-7. LCD BLOCK DIAGRAM IC5502 @¢ IC5502 @™ 2.0Vp-p 2.0Vp-p IC5502 @º 2.0Vp-p IC5502 8 IC5502 9 IC5502 !º IC5602 7 0.4Vp-p 0.3Vp-p 0.1Vp-p 5.0Vp-p 6.7 KHz IC5601 @§ 3.0Vp-p 5.48 MHz IC5601 #¶ 2.8Vp-p 3-23 3-24 3-25...
Page 53: Evf Block Diagram
CCD-TRV66E/TRV77E CCD-TRV66E/TRV77E 3-8. EVF BLOCK DIAGRAM IC901 !§ IC901 !¡ 0.9Vp-p 2.4Vp-p IC901 !£ 1.1Vp-p IC901 3 IC901 1,5 2.0Vp-p 20 msec 2.0Vp-p 20 msec IC901 7 1.1Vp-p 20 msec 3-27 3-28...
Page 54: Power Block Diagram
CCD-TRV66E/TRV77E 3-9. POWER BLOCK DIAGRAM 3-29 3-30 3-31 3-32E...
Page 55: Frame Schematic Diagram-1
CCD-TRV66E/TRV77E SECTION 4 PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS 4-1. FRAME SCHEMATIC DIAGRAM-1 FRAME SCHEMATIC DIAGRAM (1/2)
Page 56 CCD-TRV66E/TRV77E FRAME SCHEMATIC DIAGRAM-2 FRAME SCHEMATIC DIAGRAM (2/2)
Page 57: Ccd Imager
CCD-TRV66E/TRV77E 4-2. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS CD-209 (CCD IMAGER) PRINTED WIRING BOARD — Ref. No. CD-209 Board; 10,000 Series — CD-209 BOARD THIS NOTE IS COMMON FOR WIRING BOARDS AND SCHEMATIC DIAGRAMS C1401 (In addition to this, the necessary note is printed in each block)
Page 58 CCD-TRV66E/TRV77E VC-214 (CAMERA PROCESSOR, Y/C PROCESSOR, FOCUS/ZOOM MOTOR DRIVE, REC/PB HEAD AMP, VIDEO/INTERFACE, IR TRANSMITTER, MODE CONTROL, SERVO, HI CONTROL, SYSTEM CONTROL, AUDIO PROCESSOR) PRINTED WIRING BOARD — Ref. No. VC-214 Board; 1,000 Series — VC-214 BOARD (SIDE A) C006...
Page 59 CCD-TRV66E/TRV77E CCD-TRV66E/TRV77E VC-214 BOARD (SIDE B) C001 A-15 C384 C-14 C827 A-11 Q016 B-15 R084 B-15 R521 D-14 R756 B-17 C004 A-14 C385 C-15 C828 A-11 Q017 A-15 R087 C-15 R526 D-14 R757 B-17 C005 B-14 C386 C-15 C829 A-11...
Page 60: Camera Processor
CCD-TRV66E/TRV77E CCD-TRV66E/TRV77E For schematic diagram • Refer to page 4-11 for printed wiring board. VC-214 BOARD (1/10) IC501 5 IC502 !º CAMERA REC/PB CAMERA REC LINE REC 3.0Vp-p 28.374 MHz 2.9Vp-p 72 nsec IC501 !¡ IC502 !º PB CAMERA REC/PB 3.0Vp-p...
Page 61 CCD-TRV66E/TRV77E For schematic diagram • Refer to page 4-11 for printed wiring board. • Refer to page 4-23 for waveforms. Y/C PROCESSOR 4-19 4-20 4-21 4-22 VC-214 (2/10)
Page 62 CCD-TRV66E/TRV77E CCD-TRV66E/TRV77E For schematic diagram • Refer to page 4-11 for printed wiring board. VC-214 BOARD (2/10) !™ !§ !ª IC202 3 IC202 @£ IC202 #¶ CAMERA REC/PB CAMERA REC/PB LINE REC 0.3Vp-p 0.3Vp-p 0.45Vp-p !™ !§ @º IC202 3 IC202 @£...
Page 63: Rec/Pb Head Amp
CCD-TRV66E/TRV77E For schematic diagram • Refer to page 4-11 for printed wiring board. • Refer to page 4-30 for waveforms. REC/PB HEAD AMP 4-27 4-28 4-29 VC-214 (4/10)
Page 64: Video/Interface
CCD-TRV66E/TRV77E For schematic diagram • Refer to page 4-11 for printed wiring board. VC-214 VC-214 BOARD (4/10) BOARD (5/10) @∞ #º #∞ CN001 !§, Q001 C IC151 3 IC151 @ª CAMERA REC CAMERA REC/PB CAMERA REC/PB 0.48Vp-p 2Vp-p 7.14 MHz 9.0Vp-p...
Page 65: Ir Transmitter
CCD-TRV66E/TRV77E CCD-TRV66E/TRV77E For schematic diagram • Refer to page 4-11 for printed wiring board. VC-214 BOARD (6/10) $™ IC751 7 CAMERA REC/PB 0.2Vp-p 4.43 MHz $£ IC751 @™ CAMERA REC/PB IR ON 0.22Vp-p 0.5 µsec/div $¢ IC751 $¡ CAMERA REC/PB IR ON 0.22Vp-p...
Page 66: Mode Control
CCD-TRV66E/TRV77E For schematic diagram • Refer to page 4-11 for printed wiring board. VC-214 BOARD (7/10) CAMERA REC/PB $∞ IC402 1 1.7Vp-p 20.0 MHz $§ IC402 $¶ 2.8Vp-p 25 Hz MODE CONTROL 4-36 4-37 4-38 VC-214 (7/10)
Page 67 CCD-TRV66E/TRV77E For schematic diagram FP-249 (S/T REEL SENSOR), FP-356 (TOP SENSOR), FP-355 (TAPE LED) FLEXIBLE BOARD • Refer to page 4-11 for printed wiring board. PRINTED WIRING BOARD — Ref. No. FP-249, 356, 355 FLEXIBLE board; 5,000 series — VC-214...
Page 68 CCD-TRV66E/TRV77E For schematic diagram VL-23 (VIDEO LIGHT) PRINTED WIRING BOARD (TRV66E only) • Refer to page 4-11 for printed wiring board. — Ref. No. VL-23 Board; 2,000 Series — VC-214 BOARD (9/10) CAMERA REC/PB %™ IC604 $º 3.2Vp-p 20.0 MHz %£...
Page 69: Audio
CCD-TRV66E/TRV77E For schematic diagram • Refer to page 4-11 for printed wiring board. AUDIO 4-47 4-48 4-49 VC-214 (10/10)
Page 70: Steady Shot), Pj-92 (Av In/Out)
CCD-TRV66E/TRV77E SE-83 (STEADY SHOT), PJ-92 (AV IN/OUT) PRINTED WIRING BOARDS — Ref. No. SE-83, PJ-92 Board; 2,000 Series — SE-83 BOARD PJ-92 BOARD C451 C101 C452 C102 C453 C103 C454 C104 C457 C105 C458 C106 C459 C107 C460 C108 C461...
Page 71: Steady Shot), Pj-92 (Av In/Out)
CCD-TRV66E/TRV77E STEADY SHOT AV IN/OUT 4-53 4-54 SE-83 PJ-92...
Page 72: Stereo Mic Amp, Laser Link
CCD-TRV66E/TRV77E MA-351 (STEREO MIC AMP, LASER LINK) PRINTED WIRING BOARD — Ref. No. MA-351 Board; 2,000 Series — MA-351 BOARD C301 IC301 C302 IC322 C303 C304 J301 C305 C306 L301 C333 C334 Q301 C335 Q302 C336 Q303 C337 Q304 C338...
Page 73: Stereo Mic Amp, Laser Link
CCD-TRV66E/TRV77E STEREO MIC AMP, LASER LINK 4-57 4-58 4-59 MA-351...
Page 74: Printed Wiring Board
CCD-TRV66E/TRV77E PD-105 (RGB DECODER, LCD, TIMING GENERATOR, BACK LIGHT DRIVE) PRINTED WIRING BOARD — Ref. No. PD-105 Board; 10,000 Series — PD-105 BOARD C5501 L5504 R5647 D-8 C5502 L5601 R5648 D-5 C5503 L5603 R5651 D-8 C5504 L5604 R5652 D-8 C5505...
Page 75 CCD-TRV66E/TRV77E CCD-TRV66E/TRV77E PD-105 BOARD (1/2) CAMERA REC/PB IC5801 2 3.0Vp-p 23.78 KHz IC5502 8 0.4Vp-p IC5502 9 0.3Vp-p IC5502 !º 0.1Vp-p IC5502 @º 2.0Vp-p IC5502 @™ 2.0Vp-p IC5502 @¢ 2.0Vp-p RGB DECODER, LCD 4-63 4-64 4-65 PD-105 (1/2)
Page 76: Timing Generator, Back Light Drive)(2/2)
CCD-TRV66E/TRV77E CCD-TRV66E/TRV77E For schematic diagram • Refer to page 4-60 for printed wiring board. PD-105 BOARD (2/2) CAMERA REC/PB IC5601 @§ 3.0Vp-p 5.48 MHz IC5601 #¶ 2.8Vp-p !º IC5602 7 5.0Vp-p 6.7 KHz TIMING GENERATOR, BACK LIGHT DRIVE 4-66 4-67...
Page 77: B/W Evf
CCD-TRV66E/TRV77E VF-129 (B/W EVF) PRINTED WIRING BOARD — Ref. No. VF-129 Board; 3,000 Series — VF-129 BOARD VF-129 BOARD C901 R905 CAMERA REC/PB C902 R906 C903 R907 IC901 1,5 C904 R908 C905 R909 C906 R910 C907 R911 C908 R912 C909 R913 2.0Vp-p...
Page 78: User Control
CCD-TRV66E/TRV77E CF-56 (USER CONTROL) PRINTED WIRING BOARD — Ref. No. CF-56 Board; 2,000 Series — CF-56 BOARD BH001 D-5 R016 R020 C001 D-10 R022 C002 D-10 R023 C003 D-12 R025 R026 CN001 B-11 R029 B-12 CN002 A-14 R031 CN003 E-11...
Page 79: User Control
CCD-TRV66E/TRV77E USER CONTROL 4-75 4-76 4-77 CF-56/MR-8500...
Page 80: Dc/Dc Converter
CCD-TRV66E/TRV77E DD-117 (DC/DC CONVERTER) PRINTED WIRING BOARD — Ref. No. DD-117 Board; 2,000 Series — DD-117 BOARD C801 D806 Q828 R852 C802 D809 Q829 R853 C803 D810 Q830 R854 C804 D812 Q831 R859 C805 D813 Q832 R864 C806 D814 Q833...
Page 81 CCD-TRV66E/TRV77E DD-117 BOARD CAMERA REC/PB IC801 4 0.75Vp-p 2 µsec IC801 ^¢ 0.75Vp-p 2 µsec DC/DC CONVERTER 4-81 4-82 4-83 4-84 DD-117...
Page 82 CCD-TRV66E/TRV77E CCD-TRV66E/TRV77E CONTROL SWITCH BLOCK 4-88E FK-8500/SS-8500...
Page 83: Adjustments
CCD-TRV66E/TRV77E SECTION 5 ADJUSTMENTS 5-1. CAMERA SECTION ADJUSTMENT 1-1. PREPARATIONS BEFORE ADJUSTMENT (CAMERA SECTION) 1-1-1. List of Service Tools • Oscilloscope • Color monitor • Vectorscope • Regulated power supply • Digital voltmeter Ref. No. Name Parts Code Usage Auto white balance adjustment/check...
Page 84: Adjusting Items When Replacing Main Parts
1-1-2. Adjusting items when replacing main parts When replacing main parts, adjust the items indicated by r in the following table. Replacing parts Adjustment Adjusting item Section Initialization of D, E, F page data Camera HALL adj. Camera Flange back adj. Camera AGC gain calibration adj.
Page 85: Preparations
1-1-3. Preparations Note 1: For details of how remove the cabinet and boards, refer to “2. DISASSEMBLY”. Note 2: When performing only the adjustments, the lens block and boards Pattern box need not be disassembled. Connect the equipment for adjustments according to Fig. 5-1-3. By setting the “Forced Camera Power ON mode”, the camera power can be turned ON even if the front panel block (MA- 351 board, power switch, microphone unit) has been removed.
Page 86 Note: Press the battery switch of the battery terminal using adhesive tape, etc. Color monitor Vector scope Regulated power supply (Note) Terminated at 75 Ω (8.4 ± 0.1Vdc) Need not connected CD-209 board CN1401 Lens block Battery terminal Adjustment remote commander Extension cable (16P, 0.5mm)
Page 87: Precaution
FOCUS switch (MR-8500 block) ......MANUAL VIDEO LIGHT switch (MA-351 board) 10. PROGRAM AE (CF-56 board) ........Auto (CCD-TRV66E) ............... OFF 11. BACK LIGHT (CF-56 board) .......... OFF DEMO MODE (Menu display) ........OFF 12. PICTURE EFFECT (CF-56 board) ......... OFF DIGITAL ZOOM (Menu display) ........
Page 88: Initialization Of D, E, F Page Data
1-2. INITIALIZATION OF D, E, F PAGE DATA 3. D Page Table Note : Fixed data-1 : Initialized data. (Refer to “1. Initializing the D,E,F Page Data”.) 1. Initializing the D,E,F Page Data Fixed data-2 : Modified data. (Refer to “2. Modification of D, E, F Note: If the D,E,F page data has been initialized, “Modification of D, E, F Page Data”.) Page Data”...
Page 89 4. F Page table Address Remark Note : Fixed data-1 : Initialized data. (Refer to “1. Initializing the D,E,F Initial value Page Data”.) Fixed data-2 Fixed data-2 : Modified data. (Refer to “2. Modification of D, E, F Page Data”.) Fixed data-1 Address Remark...
Page 90 Address Remark Address Remark Initial value Initial value Fixed data-1 REC L level adj. (Initialized data) HALL adj. Max gain adj. Fixed data-1 (Initialized data) REC C current adj. Color reproduction adj. Fixed data-1 Fixed data-1 (Initialized data) Color reproduction adj. Fixed data-1 (Initialized data) Auto white balance adj.
Page 91 Address Remark Address Remark Initial value Initial value Fixed data-1 Fixed data-1 (Initialized data) (Initialized data) Fixed data-2 Fixed data-1 Flange back adj. Color reproduction adj. Fixed data-1 (Initialized data) Table. 5-1-3. Fixed data-2 Fixed data-1 (Initialized data)
Page 92 5. E Page Table Address Remark Note : Fixed data-1 : Initialized data. (Refer to “1. Initializing the D,E,F Initial value Page Data”.) Fixed data-1 Fixed data-2 : Modified data. (Refer to “2. Modification of D, E, F Page Data”.) (Initialized data) Address Remark...
Page 93 Address Remark Address Remark Initial value Initial value Fixed data-2 Fixed data-1 Fixed data-1 (Initialized data) Fixed data-2 Fixed data-1 (Initialized data) Fixed data-2 (Modified data, copy the data built in the same model.) Fixed data-1 (Initialized data) VCO adj. (LCD) Fixed data-2 (Modified data, copy the data built in the same model.)
Page 94 Address Remark Initial value V-COM adj. (LCD) Fixed data-1 Color adj. (LCD) Fixed data-1 (Initialized data) Fixed data-2 (Modified data, copy the data built in the same model.) Fixed data-1 Table. 5-1-4. 5-12...
Page 95: Camera System Adjustments
Select page: 6, address: 01, set data: 6D, and press the PAUSE STEADY SHOT (Menu display) ........OFF button of the adjustment remote commander. (The HALL VIDEO LIGHT (CCD-TRV66E) ........OFF adjustment is performed and the adjustment data is stored in page: F, address: 47 and 48.) Adjusting method: Select page: 6, address: 02, and check that the data is “01”.
Page 96: Flange Back Adjustment (2)
38 to 3D, 5A to 5E, F8 to FA 2) DIGITAL ZOOM (Menu display) ........OFF 3) STEADY SHOT (Menu display) ........OFF Switch setting: 4) VIDEO LIGHT (CCD-TRV66E) ........OFF 1) NIGHT SHOT ..............OFF 2) DIGITAL ZOOM (Menu display) ........OFF Checking method: 3) STEADY SHOT (Menu display) ........
Page 97: Picture Frame Setting
DIGITAL ZOOM (Menu display) ........OFF Switch setting: STEADY SHOT (Menu display) ........OFF NIGHT SHOT ..............OFF VIDEO LIGHT (CCD-TRV66E) ........OFF DIGITAL ZOOM (Menu display) ........OFF STEADY SHOT (Menu display) ........OFF Adjusting method: VIDEO LIGHT (CCD-TRV66E) ........OFF Select page: 0, address: 01, and set data: 01.
Page 98: Color Reproduction Adjustment
Upper two digits 2) DIGITAL ZOOM (Menu display) ........OFF 3) STEADY SHOT (Menu display) ........OFF Switch setting: 4) VIDEO LIGHT (CCD-TRV66E) ........OFF 1) NIGHT SHOT ..............OFF 2) DIGITAL ZOOM (Menu display) ........OFF Adjusting method: 3) STEADY SHOT (Menu display) ........OFF 1) Select page: 0, address: 01, and set data: 01.
Page 99: Max Gain Adjustment
Note: The right two digits of the DDS display data is the object data. DIGITAL ZOOM (Menu display) ........OFF 00 00 XX STEADY SHOT (Menu display) ........OFF Object data VIDEO LIGHT (CCD-TRV66E) ........OFF Switch setting: NIGHT SHOT ..............OFF Adjusting method: DIGITAL ZOOM (Menu display) ........OFF Select page: 0, address: 01, and set data: 01.
Page 100: Auto White Balance Adjustment
Switch setting: 1) NIGHT SHOT ..............OFF 2) DIGITAL ZOOM (Menu display) ........OFF 3) STEADY SHOT (Menu display) ........OFF 4) VIDEO LIGHT (CCD-TRV66E) ........OFF Adjusting method: 1) Place the C14 filter for color temperature correction on the lens.
Page 101: White Balance Check
NIGHT SHOT ..............OFF DIGITAL ZOOM (Menu display) ........OFF 1.0mm STEADY SHOT (Menu display) ........OFF VIDEO LIGHT (CCD-TRV66E) ........OFF 1.0mm Checking method: Check that the lens is not covered with either filter. Select page: 6, address: 01, set data: 0F, and press the PAUSE button of the adjustment remote commander.
Page 102: Angular Velocity Sensor Sensitivity Preset And Steady Shot Check
12. Angular Velocity Sensor Sensitivity Preset and Steady Shot Check Check the output of the angular velocity sensor. Precautions on the Parts Replacement There are two types of repair parts. Type A ENC03JA Type B ENC03JB Replace the broken sensor with a same type sensor. If replace with other type parts, the image will vibrate up and down or left and right during hand-shake correction operations.
Page 103: Horizontal Slant Check
1-4. MONOCHROME ELECTRONIC VIEWFINEDER 1-4-2. Centering Adjustment SYSTEM ADJUSTMENT Mode Playback Signal Alignment tape : 1-4-1. Horizontal Slant Check For checking operation Mode Playback (WR5-5CSP) Monoscope section Signal Alignment tape : For checking operation Specified Value ± 4% (WR5-5CSP) Monoscope section Adjusting method: Use the centering adjustment ring and adjust so that the left, Specified Value...
Page 104: Aberration Adjustment
1-4-4. Aberration Adjustment 1-4-5. Horizontal Amplitude Adjustment (VF-129 board) Mode VTR stop Mode Playback Signal Dot pattern Signal Alignment tape : 2 × a1 For checking operation Specified Value 0.8 × a2 (WR5-5CSP) Monoscope section Adjusting method: Adjusting Element C909 (SOL901) 1) Adjust the aberration adjustment ring so that the tracing of the Specified Value 10 ±...
Page 105: Vertical Amplitude Adjustment (Vf-129 Board)
1-4-6. Vertical Amplitude Adjustment (VF-129 board) 1-4-7. Brightness Adjustment (VF-129 board) Mode Playback Mode Playback Signal Alignment tape : Signal Alignment tape : For checking operation For checking operation (WR5-5CSP) (WR5-5CSP) Monoscope section Monoscope section Adjusting Element RV903 Adjusting Element RV904 Specified Value 10 ±...
Page 106: Lcd System Adjustment
1-5. LCD SYSTEM ADJUSTMENT 1. LCD Initial Data Input Note 1: The back light (fluorescent tube) is driven by a high voltage AC Mode VTR stop power supply. Therefore, do not touch the back light holder to Signal Arbitrary avoid electrical shock. Note 2: When replacing the LCD unit, be careful to prevent damages Adjustment Page caused by static electricity.
Page 107: Vco Adjustment (Pd-105 Board)
2. VCO Adjustment (PD-105 board) 3. D range Adjustment (PD-105 board) Set the VCO free-run frequency. If deviated, the LCD screen will Set the D range of the RGB decoder used to drive the LCD to the be blurred. specified value. If deviated, the LCD screen will become blackish or saturated (whitish).
Page 108: Bright Adjustment (Pd-105 Board)
4. Bright Adjustment (PD-105 board) 5. Contrast Adjustment (PD-105 board) Set the level of the VIDEO signal for driving the LCD to the specified Set the level of the VIDEO signal for driving the LCD to the specified value. If deviated, the screen image will be blackish or saturated value.
Page 109: V-Com Level Adjustment (Pd-105 Board)
6. V-COM Level Adjustment (PD-105 board) 7. Color Adjustment (PD-105 board) Set the common electrode drive signal level of LCD to the specified Set the color saturation to the standard value. If deviated, the color value. will be to dark or light. Mode VTR stop Mode...
Page 110: V-Com Adjustment (Pd-105 Board)
8. V-COM Adjustment (PD-105 board) 9. White Balance Adjustment (PD-105 board) Set the DC bias of the common electrode drive signal of LCD to the Correct the white balance. specified value. If deviated, the LCD screen color cannot be reproduced. If deviated, the LCD display will move, producing flicker and Mode VTR stop...
Page 111: Mechanism Section Adjustment
5-2. MECHANISM SECTION ADJUSTMENT Mechanism Section adjustments, checks, and replacement of mechanism parts, refer to the separate volume “8mm Video Mechanism Adjustment Manual B Mechanism ”. 2-1. OPERATING WITHOUT CASSETTE 2-2. TAPE PATH ADJUSTMENT Refer to “Section 2. DISASSEMBLY” and supply the power 1.
Page 112: Video Section Adjustment
5-3. VIDEO SECTION ADJUSTMENTS 3-1. PREPARATIONS BEFORE ADJUSTMENTS Use the following measuring instruments for video section adjustments. 3-1-1. Equipment to Required 1) TV monitor 2) Oscilloscope (dual-phenomenon, band width above 30 MHz with delay mode) (Unless specified otherwise, use a 10 : 1 probe.) 3) Frequency counter 4) Pattern generator with video output terminal...
Page 113: Precautions On Adjusting
1. VC-214 board CN501 (16P, 0.5mm) CN910 2. VC-214 board CN551 (24P, 0.5mm) 3. VL-23 board CN151 (8P, 0.5mm) (CCD-TRV66E) 4. Intelligent accessory shoe (8P, 0.8mm) (CCD-TRV77E) Cabinet (R) (Camera function switch (CF-56 board), LCD block, viewfinder) need not be connected. But removing the...
Page 114: Connecting The Equipments
3-1-4. Connecting the Equipments Connecting the measuring instruments as shown in Fig. 5-3-2 and perform the adjustments. Connecting the TV Monitor and Regulated Power Supply Battery terminal Main Unit TV monitor Regulated power supply 8.4 0.1Vdc VIDEO Connect when using the camera mode or playing back.
Page 115: Alignment Tape
3-1-5. Alignment Tape 3-1-6. Input/Output Level and Impedance The following table lists alignment tapes which are available. Video input/output Use the tape specified in the signal column for each adjustment. Phono jack, 1 Vp-p, 75Ω, If the type of tape to be used for checking operations is not specified, unbalanced, sync negative use whichever type.
Page 116: System Control System Adjustment
1) AUTO FOCUS ..............OFF 2) LCD screen ..............Closed 3) NIGHT SHOT ..............OFF Digital voltmeter 4) VIDEO LIGHT (CCD-TRV66E) ........OFF Fig. 5-3-4. Connection: 1) Connect the regulated power supply and the digital voltmeter to the battery terminal as shown in Fig. 5-3-4.
Page 117: Servo System Adjustments
3-3. SERVO SYSTEM ADJUSTMENTS 2. Switching Position Adjustment (VC-214 board) If deviated in this case causes switching noise or jitter on the played 1. CAP FG Offset Adjustment (VC-214 board) back screen. Improve the capstan servo characteristic. If it is not correct. jitters will increase.
Page 118: Video System Adjustments
3-4. VIDEO SYSTEM ADJUSTMENTS 2. AFC f Adjustment (VC-214 board) Adjust the pull-in range of the A/D converted clock generator during playback. Video system adjustments must be performed in the following order. Mode VTR stop [Adjusting Order] Signal No signal 28MHz origin oscillation adjustment Pin 4 of CN910 (AFC f0) Measurement Point...
Page 119: Filter F Adjustment (Vc-214 Board)
3. Filter f Adjustment (VC-214 board) 4. Y OUT Level Adjustment (VC-214 board) Adjust the f frequency of the IC151 built-in filter. Set the Y signal output level. (Adjust the D/A converter out put level of IC151.) Mode VTR stop Mode VTR stop Signal...
Page 120: C Out Level Adjustment (Vc-214 Board)
5. C OUT Level Adjustment (VC-214 board) 6. RP Filter f Adjustment (VC-214 board) Set the chroma signal output level. (Adjust the D/A converter out Adjust the LPF of the playback RF amplifier (IC001). put level of IC151.) Mode VTR stop Mode VTR stop Signal...
Page 121: Rec Y Current Adjustment (Vc-214 Board)
7. REC Y Current Adjustment (VC-214 board) Adjust the Y FM signal recording current. Mode VTR recording (SP mode) Signal No signal Pin 0 of CN910 (REC RF) Measurement Point Measuring Instrument Oscilloscope (20 MHz BW LIMIT: OFF) Adjustment Page Adjustment Address 73 to 7A Specified Value...
Page 122: Rec L Level Adjustment (Vc-214 Board)
8. REC L Level Adjustment (VC-214 board) Set the recording levels of the REC AFM signal and REC ATF signal. Processing after completed adjustment only for the model If the level is too low, the audio S/N will deteriorated, tracking will without REC switch: not be stable, or SP/LP will not be discriminated properly.
Page 123: Rec C Current Adjustment (Vc-214 Board)
9. REC C Current Adjustment (VC-214 board) Set the recording current levels of the REC Chroma signal. If it is too low, chroma signal noise in played back picture will increased. If too high, Y signal noises will increase and white modulation noises will be produced.
Page 124: Ir Transmitter Adjustments
3-5. IR TRANSMITTER ADJUSTMENTS 2. IR Video Deviation Adjustment (VC-214 board) Mode Camera standby Adjust using a IR receiver jig (J-6082-383-A). Subject Arbitrary Note : If the distance between the IR receiver jig and the camcorder is Measurement Point VIDEO OUT terminal of IR receiver jig below 1m, cover the LASER LINK emitter with a ND filter.
Page 125: Ir Audio Deviation Adjustment (Vc-214 Board)
3. IR Audio Deviation Adjustment (VC-214 board) Adjusting method: Mode VTR recording Select page: 0, address: 01, and set data: 01. Signal Audio signal : Connect the audio level meter to the AUDIO L terminal of the 400Hz, –7.5dBs : L or R of AUDIO IR receiver jig.
Page 126: Audio System Adjustment
3-6. AUDIO SYSTEM ADJUSTMENT [Connecting the measuring instruments for the audio] • Perform the adjustment using color bar signal as a video signal Connect the audio system measuring instruments in addition to the input for the VIDEO terminal. video system measuring instruments as shown in Fig. 5-3-19, and •...
Page 127: Mhz Deviation Adjustment (Vc-214 Board)
1. 1.5 MHz Deviation Adjustment (VC-214 board) 2. 1.7 MHz Deviation Adjustment (VC-214 board) Sets the spectrum of the L-ch ((L+R)/2 signal) level modulated Sets the spectrum of the R-ch ((L-R)/2 signal) level modulated during during recording. If deviated, the crosstalk signal of the audio signal recording.
Page 128: Bpf F0 Adjustment (Vc-214 Board)
3. BPF f0 Adjustment (VC-214 board) Sets the BPF passing frequency so that the AFM signal can separate from the playback RF signal properly. If deviated. the mono/stereo mode will be differentiated incorrectly, and noises and distortions will increase during high volume playback. Mode Playback Signal...
Page 129: Service Mode
5-4. SERVICE MODE 4-1. ADJUSTMENT REMOTE COMMANDER 2. Precautions Upon Using the Adjustment Remote Commander The adjustment remote commander is used for changing the calculation coefficient in signal processing, EVR data, etc. The Mishandling of the adjustment remote commander may erase the correct adjustment data at times.
Page 130: Data Process
4-2. DATA PROCESS The calculation of the DDS display and the adjustment remote commander display data (hexadecimal notation) are required for obtaining the adjustment data of some adjustment items. In this case, after converting the hexadecimal notation to decimal notation, calculate and convert the result to hexadecimal notation, and use it as the adjustment data.
Page 131: Service Mode
4-3. SERVICE MODE Note: After the completion of the all adjustments, cancel the service mode by either of the following ways. Unplug the main power supply and remove the lithium battery. (In this case, date and time and menu setting have been set by users are canceled.
Page 132: Emergency Memory Address
2. Emergency Memory Address 2-1. EMG Code (Emergency Code) The codes shown in the following table which correspond to errors that occur are recorded in addresses 10, 14, and 18. Page F Address 10 to 1B Code Type of Emergency Address Contents No error...
Page 133: Msw Codes
2-2. MSW Codes • The lower parts of the data of addresses 12, 16 and 1A represent the MSW codes (mode switch, mechanism position) when errors occurs. • The upper parts of the data of addresses 12, 16 and 1A represent, when the mechanism position is to be moved, the MSW codes at the start of movement (when moving the loading motor).
Page 134: Bit Value Discrimination
3. Bit Value Discrimination Bit values must be discriminated using the display data of the Display on the Bit values adjustment remote commander for the following items. Us the table adjustment bit3 bit2 bit1 bit0 below to discriminate if the bit value is “1” or “0”. remote commander bit7...
Page 135: Record Of Use Check
6. Record of Use Check Page 2 Address A2 to AA Function Remarks Drum rotation Hour (H) 1000th place digit and 100th place digit of counted time (decimal digit) counted time Hour (L) 10th place digit and 1st place digit of counted time (decimal digit) (BCD code) Minute User initial power...
Page 136: Switch Check (2)
8. Switch Check (2) Page 2 Address 60 to 66 Using method: 1) Select page: 2, address: 60 to 66. 2) By discriminating the display data, the pressed key can be discriminated. Data Address 00 to 0B 0C to 23 24 to 3E 3F to 5C 5D to 80...
Page 137: Repair Parts List
CCD-TRV66E/TRV77E SECTION 6 REPAIR PARTS LIST 6-1. EXPLODED VIEWS NOTE: • -XX, -X mean standardized parts, so they may • The mechanical parts with no reference number The components identified by mark ! or have some differences from the original one.
Page 138: Cabinet (R) Block Assembly
6-1-2. CABINET (R) BLOCK ASSEMBLY SP901 supplied supplied 57 58 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks 1-475-621-11 SWITCH BLOCK, CONTROL(MR-8500) 3-959-978-02 CUSHION, PANEL 3-948-339-61 TAPPING 3-053-706-01 COVER (R) (93), HINGE A-7073-841-A CF-56 BOARD, COMPLETE (TRV66E:AEP1,EE,NE,RU,E,HK,AUS,CN) 1-672-668-21 FP-62 FLEXIBLE BOARD 3-053-706-11 COVER (R) (93), HINGE...
Page 139: Lcd Block Assembly
6-1-3. LCD BLOCK ASSEMBLY supplied LED901 supplied ND901 LCD901 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks 4-981-286-01 SCREW (M1.7X2) (IB LOCK) X-3949-541-1 CABINET (C) (93) ASSY, P 1-668-963-21 FP-642 FLEXIBLE BOARD 3-053-703-11 WINDOW (93), LCD (TRV66E) 3-987-625-11 COVER (M), HINGE 3-053-703-31 WINDOW (93), LCD (TRV77E) X-3949-335-7 CABINET (M (93)) ASSY, P...
Page 140: Cabinet (L) Block And Main Boards Assembly
6-1-4. CABINET (L) BLOCK AND MAIN BOARDS ASSEMBLY (TRV77E) not supplied supplied (TRV66E) supplied supplied supplied J001 supplied supplied supplied Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks * 151 3-975-522-11 COVER, JACK 1-672-665-11 FP-54 FLEXIBLE BOARD X-3948-315-1 CABINET (L) ASSY A-7073-832-A VL-23 BOARD, COMPLETE (TRV66E) 3-052-815-01 BELT (ES), GRIP...
Page 141: Evf Block Assembly
6-1-5. EVF BLOCK ASSEMBLY V901 supplied supplied IC1401 224 225 M905 supplied M906 Be sure to read “Precautions upon replacing CCD imager” on page 4-9 when changing the CCD imager. Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks 3-948-339-01 SCREW, TAPPING...
Page 142: Cassette Compartment Assembly
6-1-6. CASSETTE COMPARTMENT ASSEMBLY LS CHASSIS ASSEMBLY (See page 6-7) MECHANISM CHASSIS ASSEMBLY (See page 6-8) Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks A-7040-421-A DAMPER ASSY X-3949-383-1 GEAR ASSY (E), GOOSENECK 7-624-102-04 STOP RING 1.5, TYPE -E 3-947-503-01 SCREW (M1.4X2.5) X-3949-153-2 CASSETTE COMPARTMENT ASSY 3-727-176-01 WASHER, STOPPER...
Page 143: Ls Chassis Assembly
6-1-7. LS CHASSIS ASSEMBLY S002 S001 D001 FP-249 (not supplied) Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks A-7040-419-A BASE (S) BLOCK ASSY, GUIDE 3-965-579-01 ROLLER, PINCH PRESS A-7040-418-B BASE (T) BLOCK ASSY, GUIDE 3-965-563-01 GEAR, T SOFT 3-965-559-01 STOPPER (T) 3-965-565-01 CLAW, T SOFT 3-965-557-01 STOPPER (T), GB...
Page 144: Mechanism Chassis Assembly
6-1-8. MECHANISM CHASSIS ASSEMBLY Note TYPE A TYPE B (Direct bearing type) (Shaft press fit type) M901 Circular rib Radial rib (When a drum is viewed from the top.) 81 1 M903 M902 S901 Note Ref.No. M901 TYPE supplied SCREW ASSY, DRUM ATTACHED ∫...
Page 145: Electrical Parts List
CD-209 CF-56 6-2. ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in the • RESISTORS When indicating parts by reference number, parts list may be different from the parts All resistors are in ohms. please include the board name. specified in the diagrams or the components METAL: metal-film resistor used on the set.
Page 146 CF-56 DD-117 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R039 1-216-838-11 METAL CHIP 1/16W C829 1-162-966-11 CERAMIC CHIP 0.0022uF 10% R040 1-216-838-11 METAL CHIP 1/16W C830 1-162-966-11 CERAMIC CHIP 0.0022uF 10% R041 1-216-838-11 METAL CHIP 1/16W C831 1-164-489-11 CERAMIC CHIP...
Page 147 DD-117 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks D814 8-719-073-03 DIODE MA8082-(K8).S0 Q813 8-729-037-53 TRANSISTOR 2SA1832F-Y/GR(TPL3) D815 8-719-073-03 DIODE MA8082-(K8).S0 Q814 8-729-046-98 TRANSISTOR CPH6702-TL D816 8-719-027-76 DIODE 1SS357-TPH3 Q815 8-729-046-98 TRANSISTOR CPH6702-TL D817 8-719-073-02 DIODE MA728-(K8).S0 Q817 8-729-044-58 TRANSISTOR SI2304DS-T1 D818...
Page 148 DD-117 FP-249 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R816 1-218-879-11 RES,CHIP 0.50% 1/16W R884 1-216-845-11 METAL CHIP 100K 1/16W R817 1-218-879-11 RES,CHIP 0.50% 1/16W R887 1-216-849-11 METAL CHIP 220K 1/16W R818 1-216-813-11 METAL CHIP 1/16W R888 1-216-845-11 METAL CHIP...
Page 149 C304 1-107-826-91 CERAMIC CHIP 0.1uF D301 8-719-061-86 DIODE DCR2810 C305 1-107-826-91 CERAMIC CHIP 0.1uF D302 8-749-060-65 DIODE DCC3810 D303 8-719-061-82 DIODE TLSU1002(TPX1,SONY) C333 1-162-927-11 CERAMIC CHIP 100PF D305 8-719-073-01 DIODE MA111-(K8).S0 (TRV77E) D321 8-719-073-03 DIODE MA8082-(K8).S0 C334 1-107-826-91 CERAMIC CHIP 0.1uF...
Page 150 MA-351 PD-105 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks < RESISTOR > < SWITCH > R301 1-216-823-11 METAL CHIP 1.5K 1/16W S301 1-692-605-11 SWITCH, SLIDE (VIDEO LIGHT) (TRV66E) R302 1-216-810-11 METAL CHIP 1/16W S302 1-771-331-41 SWITCH, PUSH (1 KEY)(POWER/VTR) R303 1-216-817-11 METAL CHIP 1/16W...
Page 151 PD-105 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks < CONNECTOR > R5528 1-218-895-11 RES,CHIP 100K 0.50% 1/16W R5531 1-216-821-11 METAL CHIP 1/16W * CN5501 1-573-984-11 CONNECTOR, BOARD TO BOARD 10P R5532 1-216-841-11 METAL CHIP 1/16W CN5601 1-573-364-11 CONNECTOR, FFC/FPC 24P R5537 1-216-823-11 METAL CHIP...
Page 152 PD-105 PJ-92 SE-83 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R5708 1-216-810-11 METAL CHIP 1/16W < JACK > R5709 1-216-817-11 METAL CHIP 1/16W R5710 1-216-864-11 METAL CHIP 1/16W J101 1-537-747-21 TERMINAL BOARD (S VIDEO/VIDEO/AUDIO) R5801 1-216-823-11 METAL CHIP 1.5K 1/16W...
Page 153 SE-83 VC-214 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks C469 1-162-964-11 CERAMIC CHIP 0.001uF < CAPACITOR > (TRV66E:AEP,EE,NE,RU,UK/TRV77E) C470 1-162-964-11 CERAMIC CHIP 0.001uF C001 1-162-970-11 CERAMIC CHIP 0.01uF (TRV66E:AEP,EE,NE,RU,UK/TRV77E) C004 1-162-970-11 CERAMIC CHIP 0.01uF C006 1-104-752-11 TANTAL.
Page 154 VC-214 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks C085 1-162-970-11 CERAMIC CHIP 0.01uF C230 1-115-156-11 CERAMIC CHIP C086 1-115-156-11 CERAMIC CHIP C232 1-164-156-11 CERAMIC CHIP 0.1uF C088 1-162-925-11 CERAMIC CHIP 68PF C233 1-135-201-11 TANTALUM CHIP 10uF C089 1-162-923-11 CERAMIC CHIP 47PF...
Page 155 VC-214 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks C381 1-164-346-11 CERAMIC CHIP C554 1-162-970-11 CERAMIC CHIP 0.01uF C382 1-164-227-11 CERAMIC CHIP 0.022uF C555 1-107-826-91 CERAMIC CHIP 0.1uF C383 1-107-826-91 CERAMIC CHIP 0.1uF C556 1-162-970-11 CERAMIC CHIP 0.01uF C384 1-107-826-91 CERAMIC CHIP...
Page 156 VC-214 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks C709 1-164-156-11 CERAMIC CHIP 0.1uF C816 1-162-962-11 CERAMIC CHIP 470PF (TRV77E) C818 1-162-968-11 CERAMIC CHIP 0.0047uF 10% C710 1-135-201-11 TANTALUM CHIP 10uF C819 1-165-176-11 CERAMIC CHIP 0.047uF (TRV77E) C820 1-107-826-91 CERAMIC CHIP...
Page 157 VC-214 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks < FERRITE BEAD > L012 1-412-955-11 INDUCTOR 22uH L013 1-412-944-11 INDUCTOR 2.7uH FB002 1-414-229-11 INDUCTOR CHIP 0UH L015 1-412-951-11 INDUCTOR 10uH FB004 1-414-229-11 INDUCTOR CHIP 0UH L016 1-412-946-11 INDUCTOR 3.9uH FB151 1-500-329-11 INDUCTOR CHIP 0UH...
Page 158 VC-214 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks Q039 8-729-037-52 TRANSISTOR 2SC4738F-Y/GR(TPL3) < RESISTOR > Q040 8-729-042-29 TRANSISTOR RN1104F(TPL3) Q041 8-729-230-72 TRANSISTOR 2SA1362-YG-EL R003 1-216-804-11 METAL CHIP 1/16W Q042 8-729-042-29 TRANSISTOR RN1104F(TPL3) R004 1-216-818-11 METAL CHIP 1/16W Q043 8-729-047-19 TRANSISTOR 2SA1965-S-TL...
Page 159 VC-214 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R074 1-216-816-11 METAL CHIP 1/16W R215 1-216-822-11 METAL CHIP 1.2K 1/16W R075 1-216-817-11 METAL CHIP 1/16W R216 1-216-811-11 METAL CHIP 1/16W R076 1-216-816-11 METAL CHIP 1/16W R218 1-216-826-11 METAL CHIP 2.7K 1/16W...
Page 160 VC-214 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R374 1-216-809-11 METAL CHIP 1/16W R532 1-216-864-11 METAL CHIP 1/16W R375 1-216-834-11 METAL CHIP 1/16W R551 1-216-841-11 METAL CHIP 1/16W R376 1-216-834-11 METAL CHIP 1/16W R554 1-216-843-11 METAL CHIP 1/16W R377 1-216-834-11 METAL CHIP...
Page 161 VC-214 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R637 1-216-845-11 METAL CHIP 100K 1/16W R705 1-216-812-11 METAL CHIP 1/16W R638 1-216-845-11 METAL CHIP 100K 1/16W (TRV77E) R639 1-216-845-11 METAL CHIP 100K 1/16W R706 1-216-821-11 METAL CHIP 1/16W R640 1-216-845-11 METAL CHIP...
Page 162 VC-214 VF-129 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R773 1-216-817-11 METAL CHIP 1/16W R925 1-216-821-11 METAL CHIP 1/16W R774 1-216-840-11 METAL CHIP 1/16W R926 1-216-864-11 METAL CHIP 1/16W R777 1-216-864-11 METAL CHIP 1/16W (TRV77E) R801 1-217-671-11 METAL CHIP 1/10W...
Page 163 VF-129 VL-23 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks < TRANSISTOR > < CONNECTOR > Q901 8-729-230-63 TRANSISTOR 2SD1819A-QRS-TX CN151 1-774-633-11 CONNECTOR, FFC/FPC 8P Q902 8-729-106-68 TRANSISTOR 2SD1615-T1GLGK Q903 8-729-216-31 TRANSISTOR 2SA1163G-TE85L < DIODE > Q904 8-729-230-63 TRANSISTOR 2SD1819A-QRS-TX D151...
Page 164 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks LCD901 1-803-356-21 MODULE, CRYSTAL INDICATION ! LED901 1-517-858-11 LIGHT, BACK M901 A-7048-899-A DRUM BLOCK ASSY (DGH-0F1A-R)(PAL) M902 8-835-635-01 MOTOR, DC SCE12A/C-NP (CAPSTAN) M903 X-3945-401-1 MOTOR ASSY, DC (LOADING) M905 1-763-262-11 MOTOR, FOCUS STEPPING M906...
Page 165 Take a copy of CAMERA COLOR REPRODUCTION FRAME and Parts referencesheets with a clear sheet for use. CCD-TRV66E/TRV77E 〈PARTS REFERENCE SHEET〉 You can find the parts position of location of mount locations applying to VC-214 board of a set. VC-214...
Page 166 CCD-TRV66E/TRV77E Sony Corporation 99A1676-1 Printed in Japan ©1999.1 Personal A&V Products Company 9-974-128-11 Published by Quality Engineering Dept. — 254 — (Shinagawa)

This manual is also suitable for:

Handycam vision ccd-trv77e

Sony Handycam Vision CCD-TRV66E Service Manual

Service Note

Self-Diagnosis Function

General

Disassembly

Block Diagrams

Adjustments

Repair Parts List

Quick Links

Related Manuals for Sony Handycam Vision CCD-TRV66E

Summary of Contents for Sony Handycam Vision CCD-TRV66E

This manual is also suitable for:

Table of Contents