Using Dolby Pro Logic Ii, Dolby Digital And Dts Digital Surround - JVC RX-6020VBK Instructions Manual

Before you start, remember...
• Make sure that you have set the speaker information correctly (see pages 12 to 14).
• You cannot adjust the center speaker output level when you have set "CNTR SP" to "NONE."
• You cannot adjust the rear speaker output levels when you have set "REAR SP" to "NONE."
• Remember not to change the speaker setting while using any Surround mode; otherwise, it may be canceled when you deactivate the
speakers required for Surround mode.
Front Panel
STANDBY
STANDBY/ON
PHONES
SURROUND
ON/OFF
Remote Control
A/V CONTROL
TEST
TEST
1
EFFECT
EFFECT
4
MENU
7/P
ENTER
10
RETURN
SOUND
SOUND
REW
REC PAUSE
TAPE/CDR CD
FM/AM TV SOUND
FM MODE FM MODE
DIMMER TV/VIDEO SURROUND
VCR CH TV CH
REMOTE CONTROL RM - SRX6020J
Display
RX-6020V AUDIO/VIDEO CONTROL RECEIVER
FM/AM TUNING FM/AM PRESET FM MODE
SPK
ANALOG
DIGITAL AUTO L C
MEMORY
LINEAR PCM S.WFR
DIGITAL LS S
D I G I T A L
S U R R O U N D
SURROUND ON/OFF
INPUT ANALOG INPUT DIGITAL
DVD MULTI
INPUT ATT
SURROUND MODE
SPEAKERS ON/OFF
SURROUND
MODE
CENTER +/–
STANDBY/ON
RECEIVER
CENTER AUDIO
2 3
REAR L
TV
5 6
REAR•L +/–
REAR R
VCR
8 9
REAR•R +/–
SUBWOOFER
DVD
0 10
100
SLEEP
FF
CD–DISC
DVD DVD MULTI
ANALOG
/DIGITAL
VCR
SURROUND
ON/OFF
ON/OFF
MUTING
MODE
SURROUND
MODE
TV VOLUME
VOLUME
TUNED STEREO AUTO MUTING SLEEP
R PRO LOGIC ΙΙ DSP H.PHONE INPUT ATT VOLUME
MASTER VOLUME
LFE
RS
CH-
ADJUST SETTING
DVD VCR TV SOUND
CONTROL
DOWN UP
CD TAPE/CDR FM AM
SOURCE NAME
ADJUST CONTROL
UP 5/DOWN ∞
Using Dolby Pro Logic II, Dolby Digital and
DTS Digital Surround
Once you have adjusted the Surround modes, the adjustment is
memorized for each source.
• When playing back digital multichannel software (Dolby Digital
5.1 ch or DTS Digital Surround), the SURROUND MODE button
does not work.
From the remote control:
It will be convenient for you to use the remote control for
adjustments, since you can make adjustments from your listening
point by using the test signal.
• For selecting Panorama control for Pro Logic II Music, use the
buttons on the front panel.
1
Set the analog or digital input mode for the source
you like to listen and start playing.
When playing back software encoded with Dolby Digital and
DTS Digital Surround, select the digital input mode (see page
11).
2
Press SURROUND ON/OFF to
activate Surround mode.
Each time you press the button, Surround mode
turns on and off alternately.
• If you are playing back software encoded with Dolby Digital
multichannel, "DOLBY DIGITAL" is selected.
• If you are playing back software encoded with DTS Digital
Surround, "DTS SURROUND" is selected.
• If you are playing back any software other
than above, you can select "PL II MUSIC" or
"PL II MOVIE" according to the source by
pressing SURROUND MODE. (
indicator lights up on the display.)
If you like to adjust sound, go to step 3 .
TO BE CONTINUED ON THE NEXT PAGE
ON/OFF
SURROUND
SURROUND
MODE
PRO LOGIC II
21