Using Dolby Pro Logic Ii, Dolby Digital And Dts Digital Surround - JVC RX-5020VBK Instructions Manual

Before you start, remember...
• Make sure that you have set the speaker information correctly (see pages 12 to 14).
• You cannot adjust the center speaker output level when you have set "CNTR SP" to "NONE."
• You cannot adjust the rear speaker output levels when you have set "REAR SP" to "NONE."
• Remember not to change the speaker setting while using any Surround modes; otherwise, it may be canceled when you deactivate the
speakers required for the Surround mode.
Front Panel
STANDBY/ON
PHONES
SURROUND
ON/OFF
Remote Control
TV CATV
SOUND TEST
TEST
1
EFFECT
EFFECT
4
MENU
7/P
ENTER
10
RETURN
SOUND
SOUND
PTY–PTY SEARCH–PTY
REW
REC PAUSE
TAPE/CDR
FM/AM TV SOUND
FM MODE FM MODE
TV/VIDEO SURROUND
VCR CH TV/CATV CH TV VOLUME
REMOTE CONTROL RM- SRX5020J
Display
FM/AM TUNING FM/AM PRESET FM MODE
UP UP
ANALOG
STANDBY
DIGITAL AUTO
MEMORY LINEAR PCM
DIGITAL LS
DOWN DOWN
D I G I T A L
S U R R O U N D
SURROUND ON/OFF
INPUT ANALOG INPUT DIGITAL
INPUT ATT
SURROUND MODE
SPEAKERS ON/OFF
SURROUND
MODE
CENTER +/–
A/V CONTROL
STANDBY/ON
RECEIVER
CENTER AUDIO
2 3
REAR L
TV/CATV
5 6
REAR•L +/–
REAR R
VCR
8 9
REAR•R +/–
SUBWOOFER
DVD
0 10
100
SLEEP
FF
CD–DISC
CD DVD
ANALOG
VCR /DIGITAL
SURROUND
ON/OFF
ON/OFF
MUTING
MODE
SURROUND
MODE
VOLUME
AUDIO/VIDEO CONTROL RECEIVER
SPK TUNED STEREO AUTO MUTING SLEEP
L C R PRO LOGIC ΙΙ DSP H.PHONE
INPUT ATT VOLUME
S.WFR LFE
S RS
CH-
DVD VCR TV SOUND
ADJUST SETTING
CONTROL
CD TAPE/CDR FM/AM
DOWN UP
SOURCE NAME
ADJUST CONTROL
UP 5/DOWN ∞
Using Dolby Pro Logic II, Dolby Digital
and DTS Digital Surround
Once you have adjusted the sound, the adjustment is memorized for
each source.
• When playing back digital multichannel software (Dolby Digital
5.1 ch or DTS Digital Surround), the SURROUND MODE button
does not work.
From the remote control:
It will be convenient for you to use the remote control for
adjustments, since you can make adjustments from your listening
point by using the test signal.
• For selecting Panorama control for Pro Logic II Music, use the
buttons on the front panel.
1
Setting the analog or digital input mode for the
source you like to listen and start playing.
When playing back software encoded with Dolby Digital and
DTS Digital Surround, select the digital input mode (see page
11).
2
Press SURROUND ON/OFF to
activate Surround mode.
Each time you press the button, Surround mode
turns on and off alternately.
• If you are playing back software encoded with Dolby Digital
multichannel, "DOLBY DIGITAL" is selected.
• If you are playing back software encoded with DTS Digital
Surround, "DTS SURROUND" is selected.
• If you are playing back any software other
than above, you can select "PL II MUSIC" or
"PL II MOVIE" according to the source by
pressing SURROUND MODE. (
LOGIC II indicator lights up on the display.)
If you like to adjust sound, go to step 3 .
TO BE CONTINUED TO THE NEXT PAGE
MASTER VOLUME
PRO
ON/OFF
SURROUND
SURROUND
MODE
21