Selecting The Analog Or Digital Input Mode - JVC RX-8020VBK Instructions Manual

Selecting the Analog or Digital Input
Mode
When you have connected digital source components using the
digital terminals (see page 13), you need to change the input mode
for these components to the appropriate digital input mode
correctly—DGTL AUTO, DGTL DTS, or DGTL D.D.
Before you start, remember...
The digital input (DIGITAL IN) terminal setting should be
correctly done for the sources you want to select the digital input
mode for (see "6 Setting the Digital Input (DIGITAL IN)
Terminals" on page 25). Without setting this digital input terminal
correctly, you cannot change the input mode from analog input to
digital input even if you follow the procedure below.
1. Press one of the source selecting buttons—DVD, TV
(SOUND)/DBS, CD, CDR, or TAPE/MD—for which you
want to change the input mode.
The lamp on the front panel button for the selected source lights
up.
DVD MULTI DVD VCR 1 VCR 2 VIDEO
SOURCE NAME
PHONO CD CDR TAPE / MD USB AUDIO
SOURCE NAME
On the front panel
Note:
If "TAPE" has been assigned as the source name to the TAPE/MD
button when using an MD recorder, it does not work in this step.
To change the source name, see "Changing the source name" on
page 17.
2. Press INPUT ANALOG/DIGITAL (INPUT ATT)—or
ANALOG/DIGITAL INPUT on the remote control—
briefly to change the input mode.
INPUT
ANALOG/DIGITAL
INPUT ATT
On the front panel
• Each time you press the button, the input mode changes as
follows:
DGTL AUTO
L R
DIGITAL
SPEAKERS 1
DGTL AUTO
(Digital)
19
TV SOUND/DBS
DVD DVD MULTI CD
TV/DBS VIDEO CDR
FM / AM
VCR 1 VCR 2 TAPE/MD
From the remote control
ANALOG/DIGITAL
INPUT
From the remote control
VOLUME
ANALOG
DGTL AUTO: Select this for the digital input mode. The
receiver automatically detects the incoming
signals.
The DGTL AUTO indicator lights up on the
display, and the digital signal format indicators
for the detected signals also light up.
ANALOG: Select this for the analog input mode.
The ANALOG indicator lights up.
When selecting "DGTL AUTO," the following indicators
showing detected signals light up on the display.
LINEAR PCM
LINEAR PCM
: Lights up when Dolby Digital or Dolby
DIGITAL
: Lights up when DTS Surround or DTS-ES
When playing a software encoded with the Dolby Digital or DTS
FM/AM
Digital Surround, the following symptoms may occur:
• Sound does not come out at the beginning of playback.
PHONO
• Noise comes out while chapters or tracks are being searched for or
USB skipped over.
1. Press INPUT ANALOG/DIGITAL (INPUT ATT) or
ANALOG/DIGITAL INPUT on the remote control.
• "DGTL AUTO" appears on the display.
2. Press CONTROL UP 5 or DOWN ∞ on the front panel to
select "DGTL D.D" or "DGTL DTS" while "DGTL AUTO"
still remains on the display.
• Each time you press the button, the input mode changes as
follows:
L R
DIGITAL
SPEAKERS 1
DGTL AUTO
(Digital)
When selecting "DGTL D.D" or "DGTL DTS," the following
indicators showing detected signals light up on the display.
DGTL
: Always lights up.
When selecting "DGTL D.D"
: • Lights up when Dolby Digital signals
DIGITAL
When selecting "DGTL DTS"
: • Lights up when DTS Digital Surround
Note:
When you turn off the power or select another source, "DGTL D.D"
and "DGTL DTS" settings are canceled and the digital input mode is
automatically reset to "DGTL AUTO."
: Lights up when Linear PCM signals come
in.
: Lights up when the digital signals are not
recognized.
Digital EX signals come in.
signals come in.
DGTL AUTO
DGTL D.D
(Digital Dolby Digital)
DGTL DTS
(Digital)
come in.
• The frame flashes when Dolby Digital
signals are not recognized.
signals come in.
• The frame flashes when DTS Digital
Surround signals are not recognized.
VOLUME