Using The Pc Settings Feature; Setting The Pc Audio; Setting The Sleep Timer - Toshiba 26AV52U Owner's Manual

Chaptsr 6: Using the TV's fsatures
Using the PC settings feature
I
Setting the PC Audio
You can view an image from a PC on the TV screen.
When a PC is connected to the TV's PC IN terminal, you can
use the PC Settings feature to make adjustments to the image.
If the edges of the picture are cut off, readjust the
Horizontal
Position
and
Vertical Position.
If the picture is affected by
interference, readjust the
Clock Phase
and
Sampling Clock.
To adjust the PC settings:
1
Repeatedly press
~
to select PC input mode
(~ "Selecting the video input source to view" page 34).
2
Press M~U and open the
Setup
menu.
3
Highlight
PC Settings
and press
@.
Note: If
a
PC is not connected or there is no pc input
signal, this feature will be grayed out in the Setup menu.
4
Press
£
or ..,. to highlight the item you want to adjust.
5
Press'" or
~
to make the appropriate adjustments.
This function allows you to output or mute the sound from
your PC when connecting using the PC IN terminal and an
I
analog RGB cable.
(~page
19)
To set the PC Audio:
1 Press M~U and open the
Audio
menu.
2
Highlight
Audio Setup
and press
@.
3
Press £ or .... to select
PC Audio
and then press'" or
~
to
select
No
or
Yes.
Yes:
When viewing the PC input, the audio from the PC
Audio input can be heard.
No:
When viewing the PC input, there will be no audio.
Note: Because the PC and HOMI-1 inputs share the
same set of analog audio inputs, the PC Audio menu
setting influences the HDM/1 Audio menu setting. If PC
Audio is set to "No," the HDM/ 1 Audio setting changes
to "Auto." If PC Audio is set to "Yes, " the HDM/1 Audio
setting is set to "Digital" and is grayed out in the menu.
(Also see item 3 on page 11 and "Setting the HOMITM
Audio mode" on page 32.)
Setting the sleep timer
PC Settings
You can set the sleep timer to tum off the TV after a set
length of time (maximum of 180 minutes).
*
The default settings may vary depending on the input signal
format.
Note: The screen is disrupted momentarily when adjusting
the PC settings. This is not
a
sign of malfunction.
Description
Press
M~U
and open the
Setup
menu.
Highlight
Sleep Timer
and press
@.
Press the Number buttons to enter the length of time in
lO-minute increments.
To set the sleep timer using the remote control:
Press
S~EP
on the remote control to set the length of time
until the TV turns off. Repeatedly press
S~EP
to increase the
time in lO-minute increments, or press £ or .... to increase or
decrease the time in lO-minute increments, to a maximum of
180 minutes.
4
Highlight
Done
and press
@.
Note: When
a
power failure occurs, the sleep timer
setting may be cleared.
To display the remaining sleep time:
Press
S~EP.
Note: A message will display on-screen when there is one
minute remaining on the sleep timer
I
I
I
To set the sleep timer using the on-screen menus:
I 1
I
2
i
3
I
Done
Highlight this item then press
@
to get an
optimum adjustment automatically.
Helps to reduce noise and sharpen the picture.
The adjustment range is within ±16 from center.*
Helps to reduce noise and minimize periodic
vertical stripes on the screen.
The adjustment range is within
±
10 from center.*
Moves the picture left/right.
The adjustment range is within ±50 from center.*
Moves the picture up/down.
The adjustment range is within
±
10 from center.*
Reset
Vertical Positio n
Clock Phase
Sampling Clock
Auto Adjust
Vertical
Position
Horizontal
Position
Auto Adjust
Clock Phase
Sampling
Clock
Mode
To cancel the sleep timer:
Repeatedly press
SL8
P
until it is set to 0 minute.
49 \