Basic Settings - JVC UX-G6 Service Manual

Continued
Connecting MD Recorder XM-G6 Connecting Antennas
You can also connect the MD recorder XM-G6 (not Supplied FM antenna
supplied), specifically designed for UX-G6. This unit will
complete UX-G6 micro component system.
When you connect and use this unit, refer to the Instructions
supplied with it for details.
External wire
(supplied with XM-G6)
AX-UXG6
VOLTAGE SELECTOR
External wire
(supplied with UX-G6)
XT-UXG6
FROM CONNECTOR-C
1
Attach the FM antenna to the FM 75 Ω COAXIAL
terminal on the rear panel of XT-UXG6.
2
Extend the FM antenna.
XM-G6
3
TO CONNECTOR-C
Fasten it up in the position which gives you the
best reception.
Optical digital cable
(supplied with XM-G6)
• DO NOT install XM-G6 until you turn off the
system and unplug the AC power code, otherwise
installation should fail to damage the system.
• DO NOT change the vertical stacking order of XM- To connect an outdoor FM antenna
G6 as illustrated to avoid heat buildup.
Before connecting it, disconnect the supplied FM antenna.
Connecting Sub Woofer System
When using JVC external sub woofer system, connect
audio cable between AX-UXG6's SUB WOOFER OUT
jack and the input of your sub woofer system.
SUBWOOFER OUT
AX-UXG6
AX-UXG6
VOLTAGE SELECTOR
Sub Woofer System
(not supplied)
Audio cable
(not supplied)
7
Continued
Connecting Other Equipments To connect audio equipment with an optical digital
input terminal
You can connect the following equipments to the system: By using both an optical digital cable (not supplied) and an
audio cable (not supplied), connect:
• Audio equipment — used only as an analog playback • Between the optical digital input terminal on the other
device.
equipment and the optical digital output terminal on XT-
• Audio equipment with an optical digital input terminal
UXG6.
— used as a digital recording device. • Between the audio output jacks on the other equipment
and the ANALOG IN jacks.
When you connect and use these equipments, refer also to
the manuals supplied with them.
To connect audio equipment without a digital
output terminal
Connect the audio output jacks on the other equipment and
the ANALOG IN jacks, using an audio cable (not supplied).
Be sure that the plugs of the audio cables and the jacks on
the rear panel of the unit are color coded: White plugs and
jacks are for left audio signals, and red ones for right audio
signals.
• DO NOT connect other equipment while the
power is on.
• DO NOT plug in any equipment until all
connections are complete.
VOLTAGE SELECTOR (AC wall outlet)
To ANALOG IN
XT-UXG6
Before connecting the other equipment,
remove the protective plug from the terminal.
NOW, you can plug in the system and other connected
equipment FINALLY!
To audio output
on the other equipment
When connecting the AC power cord into a wall outlet, the
• By using audio cable (not supplied), connect system switches to standby mode with STANDBY/ON lamp
between the audio output jacks on the other lit red.
equipment and the ANALOG IN jacks.
9
A M
F M L O
C O O P
7 5
A X
IA
L
About the supplied FM antenna
The FM antenna supplied with this unit can only be
used as temporary measure. If reception is poor,
you can connect an outdoor FM antenna.
Outdoor FM antenna
(not supplied)
A M
L O
F M
O P
C O 7 5
A X
IA
L
A 75Ω antenna with coaxial type connector
(DIN 45325) should be used.
VOLTAGE SELECTOR (AC wall outlet)
To ANALOG IN
XT-UXG6
To DIGITAL OUT
To optical digital input
To audio output
Protective Plug
DO NOT plug in before setting the voltage selector
switch on the rear of the unit and all connection
procedure are complete (check to see page 11).
Connecting Speakers
AM antenna
You can connect the speakers using the speaker cords.
1
Vinyl-covered wire
ANTENNA
(not supplied)
AM
Speaker Cord
LOOP
AM
EXT
FM 75
COAXIAL
AM loop antenna (supplied)
1 1
Connect the AM loop antenna to the AM LOOP
Open the speaker terminal.
terminals as illustrated.
2
Insert the end of the speaker cord to the terminal.
2
Turn the AM loop antenna until you have the best Match the polarity of the speaker terminals: Red (+)
reception.
to red (+) and black (–) to black (–).
3
To connect an external AM antenna
Close the speaker terminal on the rear of the unit.
When reception is poor, connect a single vinyl-covered
wire to the AM EXT terminal and extend it horizontally.
(The AM loop antenna must remain connected.)
For better reception of both FM and AM
• Make sure the antenna conductors do not touch
any other terminals and connecting cables.
• Keep the antennas away from metallic parts of
the units, connecting cables, and the AC power
cord.

Basic Settings

REMOTE CONTROL RM-SUXG6E DIMMER
PANEL
OPEN/CLOSE DIMMER
CLOCK/TIMER
ACTIVE
SLEEP
BASS EX. CLOCK/TIMER
BASS TREBLE FM MODE
MULTI JOG
PLAY MODE REPEAT AUTO PRESET
FM/AM
TITTLE/EDIT ENTER
SET
DISPLAY
/CHARA. CANCEL
CANCEL
UP
< >
SET
< / >
DOWN
MD AUX
Setting the Display Illumination (Dimmer)
Before operating the system any further, set the clock built
in this system first, then some other basic settings.
You can adjust the brightness of around the display window.
Setting the Clock
Each time you press DIMMER button, the display window
dims and brightens alternately.
You can set the clock using the remote control whether
the system is turned on or turned off (i.e. standby mode). • While the system is turned off:
Press DIMMER button, "DISPLAY OFF" appears in the
1
Press CLOCK/TIMER button on the remote control. display window for a while and the system clock
The hour digit in the display window starts blinking. disappears.
2
Press < / > button on the remote control to adjust
Press the button again, "DISPLAY ON" appears in the
the hour, then press SET button on the remote
display window for a while and only the system clock
control (rotating MULTI JOG dial also available).
become dimmed.
• To correct the hour after pressing SET button, press
• While the system is turned on:
CANCEL button. The hour digit starts blinking again.
Press DIMMER button, both operating information and
indicators in the display window dims. The light around
3
Press < / > button on the remote control to adjust
MULTI JOG dial also becomes darker than usual.
the minute, then press SET button on the remote
Press the button again, all the illumination around the
control (rotating MULTI JOG dial also available).
display window recovers as usual.
If there is a power failure
The clock loses the setting and is reset to "0:00."
To adjust the clock again
You need to press CLOCK/TIMER button five
times until the clock setting mode is selected.
UX-G6/FS-G6
Continued
2, 3
Red
Speaker Cord
SPEAKERS
RIGHT LEFT
Black
Right speaker Left speaker
When connecting speaker cords
• Make sure to connect the cords correctly following
the right series of above steps.
During operation, wrong connection or a short
circuit make the power turned off to protect the
system.
The clock loses the setting and is reset to "0:00".
Also the MD recording may fail.
• Use only speakers with the same speaker
impedance as indicated by the speaker terminals
on the rear of the unit.
8
OPEN/CLOSE
STANDBY/ON
M I C R O C O M P O N E N T S Y S T E M U X - G 6
AUX
MULTI JOG MOS - FET VOLUME
Display window
Dimmer setting in the standby mode
Once the system is turned on, the dimmer setting in
the standby mode does affect neither normal
operations nor display indications.
10
1-9