Eeprom Data - Panasonic Digital Palmcorder PalmSight PV-DV100 Service Manual

EEPROM DATA

CAUTION:
Be sure to save the EEPROM data using PC-EVR
Adjustment Program before service and adjustment in
order to make sure to avoid an accidental data loss, etc. as
follows.
There are two EEPROM in this unit.
EEPROM IC
C.B.A.s
Main C.B.A. (Camera)
Main C.B.A. (Video)
1 How to save the EEPROM data to your PC
1. How to save the EEPROM data for Camera Circuit
1) Start up the PC-EVR Adjustment Program.
2) Select "3. Check [Camera]." in Main menu, and then
press "Enter" key.
3) Select "3. Read (Save)/Write AII EEPROM data" in
Camera check menu, and then press "Enter" key.
4) Select "3. Save all data of EEPROM" in Read (Save)/
Write All EEPROM data menu, and then press "Enter"
key.
5) Input the File name, and then press the "Enter" key. The
data of EEPROM IC will be stored to your PC.
2. How to save the EEPROM data for Video Circuit
1) Start up the PC-EVR Adjustment Program.
2) Select "2. Check [Video]." in Main menu, and then press
"Enter" key.
3) Select "3. Read (Save)/Write All EEPROM data" in
Video check menu, and then press "Enter" key.
4) Select "3. Save all EEPROM data" in Read (Save)/
Write All EEPROM data menu, and then press "Enter"
key.
5) Input the File name, and then press "Enter" key. The
data of EEPROM IC will be stored to your PC.
2 How to write the EEPROM data which was
stored in your PC to EEPROM IC
When it becomes impossible to adjust during service and
adjustment, write the EEPROM data which was stored in
your PC to EEPROM IC as follows. And readjust the
camcorder.
1. How to write the EEPROM data which was stored
for Camera circuit
1) Start up the PC-EVR Adjustment Program.
2) Select "3. Check [Camera]." in Main menu, and then
press "Enter" key.
3) Select "3. Read (Save)/Write AII EEPROM data" in
Camera check menu, and then press "Enter" key.
4) Select "4. Data write using stored file" in Read [Save]/
Write All EEPROM data menu, and then press "Enter"
key.
5) Input the saved file name, and then press "Enter" key.
The data will be written in EEPROM IC.
2. How to write the EEPROM data which was stored
for Video circuit
1) Start up the PC-EVR Adjustment Program.
2) Select "2. Check [Video]." in Main menu, and then press
"Enter" key.
3) Select "3. Read (Save)/Write All EEPROM data" in
Video check menu, and then press "Enter" key.
4) Select "4. Writing from stored data files" in Read (Save)/
Write All EEPROM data menu, and then press "Enter"
key.
5) Input the saved file name, and then press "Enter" key.
The data will be written in EEPROM IC.
EEPROM IC Ref. No.
IC301
IC6009
3 How to initialize the EEPROM IC
When the EEPROM IC or Main C.B.A. is replaced, be sure
to write the initial data to EEPROM IC. And adjust the
camcorder.
1) Start up the PC-EVR Adjustment Program.
2) Select "3. Check [Camera]." in Main menu, and then
press "Enter" key.
3) Select "3. Read (Save)/Write AII EEPROM data" in
Camera check menu, and then press "Enter" key.
4) Select "4. Data write using stored file" in Read (Save)/
Write All EEPROM data menu, and then press "Enter"
key. Input the saved file name, and then press "Enter"
key.
OR;
Select "5. Data write with initial data," and then press
"Enter" key. And press "Enter" key once again.
5) Select "2. Check [Video]." in Main menu, and then press
"Enter" key.
6) Select "3. Read (Save)/Write All EEPROM data" in
Video check menu, and then press "Enter" key.
7) Select "4. Writing from stored data files." in Read
(Save)/Write All EEPROM data menu, and then press
"Enter" key. Input the saved file name, and then press
"Enter" key.
OR;
Select "5. Writing of initial data," and then press "Enter"
key. And press "Enter" key once again. Then, input ID
Number as follows.
4 How to input ID Number
The ID number is in the EEPROM.
There are two ways to write the data of EEPROM IC after
replacing Main C.B.A. as follows:
• Selecting "4. Writing from stored data files," ID Number with
stored data file will be written automatically.
• Selecting "5. Writing of initial data," ID Number needs to be
input. There are two methods, "a" or "b," to input ID Number
as follows.
a When writing ID Number from the saved data which
is stored in 1-2:
1. Select "2. Check [Video]." in Main menu, and then press
"Enter" key.
2. Select "3. Read (Save)/Write All EEPROM data" in
Video check menu, and then press "Enter" key.
3. Select "6. Writing ID from stored file." in Read (Save)/
Write All EEPROM data menu, and then press "Enter"
key. Input the saved file name, and then press "Enter"
key. ID Number will be written automatically.
b When the original ID information can not be read
because of destruction of EEPROM etc.:
1. Select "4. Adjust [Video]." in Main menu, and then press
"Enter" key.
2. Select "7. Write products ID" in Video adjustment menu,
and then press "Enter" key. ID Number will be written
automatically.
1-9