Mechanism Section - Panasonic Digital Palmcorder PalmSight PV-DV100 Service Manual

MECHANISM SECTION

Disassembly Method
This procedure starts with the condition that the cabinet parts and Main C.B.A. have been removed.
When reassembling, perform the step(s) in the reverse order.
Perform all disassembly/reassembly and alignments procedures in STOP Position except disassembly/reassembly and
alignment procedures which have the special notes.
STEP
LOC.
No.
1
-----
-----
2
-----
3
4 2,3
5 1
6 2,3,4
7 -----
8 7
-----
9
10 2,3,4
2,3,4,10
11
12 2,3,4,10,11
13 2,3,4
14 2,3,4,13
15 2,3,4,
16 2,3,4,13,14
17 2,3,4
2,3,4
18
19 2,3,4,18
1,5,9,13,18,19
20
21
1,5,9,13,18,19,20
22 1,5,9,13,18,19,20
23 1,5,9,13,18,19,20,22
24 1,5,9,13,18,19,20,22
25 1,5,9,13,18,19,20,22,23,24
26 1,5,9,13,18,19,20,21,22
2,3,4,10,11,12,13,14,15,16
27
28 2,3,4,10,11,12,13,14,15,16,27
2,3,4,10,11,12,13,14,15,16,27,28
29
30 2,3,4,10,11,12,13,14,15,16,27,28,29
31 2,3,4,10,11,12,13,14,15,16,18,19,27
32 1,2,3,4,5,9,10,11,12,13,14,15,16,18,19,20,22,23,24,25,27,28,29,30
33 1,2,3,4,5,7,8,9,10,11,12,13,14,15,16,18,19,20,21,22,23,24,25,27,28,29,30
34 2,3,4,7,8
35 2,3,4,10,11,12,13,14,15,16,17,18,19,27,28,29,30,31
2,3,4,10,11,12,13,14,15,16,17,18,19,27,28,29,30,31,35
36
37 2,3,4,10,11,12,13,14,15,16,17,18,19,27,28,29,30,31,35,36
1,2,3,4,5,6,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,27,28,29,30,31,35,36,37,39
38
39 1,2,3,4,5,6,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,27,28,29,30,31,35,36,37,38
1,2,3,4,5,6,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,27,28,29,30,31,35,36,37,38,39
40
41 2,3,4,7,8,34
42 2,3,4,7,8,34,41
A
How to read chart shown above:
A: Order of Procedure steps.
When reassembling, perform steps(s) in reverse order.
These numbers are also used as the identification (location)
No. of parts in Figures.
B: Steps to be completed prior to the current step.
C: Part to be removed or installed.
D: Fig. No. showing Procedure or Part Location.
E: Identification of part to be removed, unhooked, unlocked,
released, unplugged, unclamped, or unsoldered.
3(S-1)=3 Screws (S-1), 3(W-1)=3 Washers (W-1),
(C-1)=Cut Washer (C-1), 2(L-1) =2 Looking Tabs (L-1)
Prior Step (s)
Head Amp C.B.A.
Guide Piece L
Guide Piece R
Garage Unit
Cylinder Unit
Dumper Unit
DEW Sensor
Mechanism F.P.C. Unit
Reduction Gear B
Mechanism Cover Unit
Idler Arm Unit
Center Gear
Tension Arm Unit
S Reel Table
T Reel Table
S Connection Gear Unit
T Brake Unit
T4 Height Plate
Pinch Arm Unit
Rail
Cylinder Base Unit
S Arm Unit
T Arm Unit
S Post Unit
T Post Unit
Loading Motor Unit
Sensor F.P.C.
Tension Drive Arm
S Brake Drive Lever
Cam Gear
Pinch Drive Arm
Intermediate Gear
Mode Switch
MIC Switch
Main Plate Unit
T4 Drive Arm
Drive Pulley
Capstan Unit
Timing Belt
Capstan Adjust Spring
Lock Lever Unit
Lock Pick Lever
B
Part
Fig. No.
DM3
DM4
DM4
DM4
DM5
DM6
DM7
DM8
DM9
DM10
DM11
DM11
DM12
DM13
DM13
DM14
DM15
DM16
DM16
DM17
DM18
DM19
DM19
DM19
DM19
DM20
DM21
DM22
DM22
DM23
DM24
DM24
DM25
DM26
DM27
DM28
DM29
DM30
DM30
DM30
DM31
DM31
C
D
F: Alignment / Adjustment which is required when installing or
replacing each parts.
CAUTION:
a. Use a wrist strap to provide ESD protection while
disassembling or assembling.
b. Removed Cut Washer is not reusable. If removed, install a
new one.
2-17
Remove
2(S-1), (L-1), FP5001
(S-2), (L-2)
(S-2), (L-2)
3(S-3) Adjustment
(S-4)
Unsolder
3(S-5), 4(L-3), Unsolder
(C-1)
(S-6), (L-4), (C-2), Hooking Portions
(C-3)
(C-4), (W-1)
(C-4), (W-1)
Hooking Portion
(S-7), (L-5), Plate
(S-8)
Hooking Portion
(S-9), (L-6), 4(L-7)
(S-10), 3(S-11)
Gear Alignment
Gear Alignment
2(S-12)
2(S-13)
Gear Alignment
Gear Alignment
Gear Alignment
(S-14)
(S-15)
Gear Alignment
(S-16), 2(S-17)
2(C-5), Hooking Portion
E
Alignment
/Adjustment
F