Sony STR-DA5300ES Service Manual page 45

• Note for Printed Wiring Boards and Schematic Diagrams
Note on Printed Wiring Board:
• X : parts extracted from the component side.
• Y : parts extracted from the conductor side.
•
: internal component.
f
•
: Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)
Caution:
Pattern face side: Parts on the pattern face side seen from
(Conductor Side) the pattern face are indicated.
Parts face side: Parts on the parts face side seen from
(Component Side) the parts face are indicated.
Caution:
Pattern face side: Parts on the pattern face side seen from
(Side B) the pattern face are indicated.
Parts face side: Parts on the parts face side seen from
(Side A) the parts face are indicated.
• D-VIDEO and DSP boards are multi-layer printed board.
However, the patterns of intermediate-layers have not been
included in this diagrams.
• Indication of transistor
C
Q These are omitted.
B E
Q
B C E
These are omitted.
* Replacement of IC3601on the D-VIDEO board used in
this set requires a special tool.
• Lead Layouts
Lead layout of conventional IC CSP (chip size package)
STR-DA5300ES
Note on Schematic Diagram:
• All capacitors are in µF unless otherwise noted. (p: pF)
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and
1 / W or less unless otherwise
4
specified.
•
: internal component.
f
• 2 : nonflammable resistor.
• C : panel designation.
Note: Note:
The components identi- Les composants identifiés par
fied by mark 0 or dotted une marque 0 sont critiques
line with mark 0 are criti- pour la sécurité.
cal for safety. Ne les remplacer que par une
Replace only with part pièce por tant le numéro
number specified.
spécifié.
• A : B+ Line.
• B : B– Line.
• H : adjustment for repair.
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
– A-VIDEO and S-VIDEO boards –
no mark : VIDEO 1 mode
– Other boards –
no mark : TUNER
• Voltages are taken with a VOM (Input impedance 10 MW).
Voltage variations may be noted due to normal produc-
tion tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal produc-
tion tolerances.
• Circled numbers refer to waveforms.
• Signal path.
F : AUDIO (ANALOG)
J : AUDIO (DIGITAL)
E : VIDEO
* Replacement of IC3601on the D-VIDEO board used in
this set requires a special tool.
• The voltage and waveform of CSP (chip size package)
cannot be measured, because its lead layout is different
surface
from that of conventional IC.
• Abbreviation
CND : Canadian model
ECE : Russian and Ukrainian models
• Circuit Boards Location
PROTECTOR (SB) board
DC-DC board
AC SW board
MIC board
SPSW board
VIDEO3 board
TEMPERATURE
DETECTION board
DISPLAY board
A-CLASS AMP board
CONNECTOR 2 board
CONNECTOR 1 board
45 45
FLI-1.8REG board
AC board
PROTECTOR (F-C) board
D-CONNECT board
CONTROL board
DSP board
BIAS board
PROTECTOR (SURR) board
KEY 1 board
MAIN VOL board
SP-TM board
TUNER (FM/AM)
S-VIDEO board
D-VIDEO board
A-VIDEO board
MAIN board
E-VOL board
POWER AMPLIFIER board
STR-DA5300ES
Ver. 1.1
CIS board
DIGITAL board
ANALOG board