Sony DCR-TRV103 Service Manual page 104

1-2-3. INITIALIZATION OF E, F PAGE DATA
1. Initializing the E, F Page Data
Note: If the E, F page data has been initialized, "Modification of E, F
Page Data" and following adjustments need to be performed again.
1) Camera system adjustments
2) "Hi8/standard 8 mm switching position adjustment" and "CAP
FG offset adjustment" of the servo & RF system adjustments
3) Video system adjustments
4) IR transmitter adjustments
5) Audio system adjustments
Adjusting Page F
Adjusting Address 00 to FF
Adjusting Page E
Adjusting Address 00 to FF
Initializing Method:
1) Select page: 0, address: 01, and set data: 80.
2) Select page: 6, address: 00, and set data: 55 (NTSC) or data:
51 (PAL).
3) Select page: 6, address: 01, set data: 55 (NTSC) or data: 51
(PAL), and press the PAUSE button of the adjustment remote
commander.
4) Select page: 6, address: 02, and check that the data is "01".
5) Select page: 0, address: 01, and set data: 00.
6) Perform "Modification of E, F Page Data".
2. Modification of E, F Page Data
If the E, F page data has been initialized, change the data of the
"Fixed data-2" address shown in the following tables by manual
input.
Modifying Method:
1) Before changing the data, select page: 0, address: 01, and set
data: 01.
2) New data for changing are not shown in the tables because
they are different in destination. When changing the data, copy
the data built in the same model.
Note : If copy the data built in the different model, the camcorder
may not operate.
3) When changing the data, press the PAUSE button of the
adjustment remote commander each time when setting new
data to write the data in the non-volatile memory.
4) Check that the data of adjustment addresses is the initial value.
If not, change the data to the initial value.
Processing after Completing Modification of F, E Page data
1) Select page: 2, address: 00, and set data: 29.
2) Select page: 2, address: 01, and set data: 29, and press the
PAUSE button of the adjustment remote commander.
3. F Page table
Note: Fixed data-1 : Initialized data. (Refer to "1. Initializing the E, F
Page Data".)
Fixed data-2 : Modified data. (Refer to "2. Modification of E, F
Page Data".)
Address Initial value
NTSC PAL
00 to 0F
10 00 00
11 00 00
12 00 00
13 00 00
14 00 00
15 00 00
16 00 00
17 00 00
18 00 00
19 00 00
1A 00 00
1B 00 00
1C
1D
1E
1F
20
21
22
23
24
25
26
27
28
29
2A
2B
2C
2D
2E 43 43
2F 3F 3F
30 AB AB
31 4B 4B
32 2B 2B
33 00 00
34 54 54
35 00 00
36
37
38 1C 1C
39 03 03
3A 25 25
3B 24 24
3C 11 11
3D 05 05
3E 0A 0A
3F 00 00
40 A0 A0
5-15
Remark
Emergency memory address
Fixed data-2
Fixed data-1
(Initialized data)
AGC gain calibration adj.
AWB standard data input
Fixed data-1
(Initialized data)
Flange back adj.
Hi8/standard 8 mm switching
position adj.
27MHz/36MHz origin oscillation adj.