Yamaha 01x Service Manual page 4

O1X
Input/Output Specifications
Analog Input
MIC/LINE INPUT 1, 2 XLR type, Balanced,
+48 V +3 V/-3 V Phantom
MIC/LINE INPUT 3 - 8 TRS Phone, Balanced
MIC/LINE INPUT Hi-Z Phone, Unbalanced
Analog Output
MONITOR OUT (L, R) Phone, Unbalanced
STEREO/AUX OUT (L, R) Phone, Unbalanced
PHONES TRS Phone, Unbalanced
Digital Input/Output
DIGITAL IN, OUT RCA PIN
MIDI IN, OUT A/B DIN (5 pin)
mLAN 1/2 IEEE 1394 (6 pin)
FOOT SWITCH 1/2 PHONE
Control
Analog Section Input Gain
Monitor Volume
Phantom Switch PHANTOM (+48 V) ON-OFF (rear panel)
Power Switch
Faders
Knobs/Dial
Panel Switches MODE
PAGE
MIXER/LAYER
FUNCTION
DISPLAY
BANK
CHANNEL
TRANSPORT
CURSOR
Others
Display LCD
Others
Supplied Accessories
Power Consumption
Dimensions
Weight
Operating free-air temperature range 10 - 35°C
4
Connector
Nominal
-46 dB – +4 dB
-46 dB – +4 dB
-46 dB – +4 dB
Connector
Nominal
-10 dBV
-10 dBV
Connector Format
IEC-60958 Consumer use
MIDI
IEEE 1394/FireWire
LINE/MIC Gain Knob 1 – 8 (+4 dB – -46 dB)
MONITOR/PHONES Knob
STANDBY/ON switch (rear panel)
Faders 1 – 8, STEREO Fader
60 mm motorized, 0 – -132 – -∞ dB
Channel knobs 1 – 8 (Data Entry)
Rotary Encoder Dial (Song Position)
INTERNAL, REMOTE, SCENE, UTILITY [BACK UP], MONITOR
SELECTED CHANNEL [LIBRARY], EQ-LOW, EQ-LOW-MID, EQ-HIGH-MID, EQ-HIGH, PAN [CH PARAM],
SEND [INST], DYNAMICS [PLUG-IN], GROUP, EFFECT
AUDIO/1–8, INST/9–16(mLAN), MIDI/17–24(mLAN), BUS-AUX/MASTER, OTHER
F1 [TRACK], F2 [MIXER], F3 [LIST], F4 [CLOSE], F5, F6, F7, F8
UP, DOWN, DISPLAY SHIFT, NAME/VALUE [METER]
< , >
SEL 1 – 8, STEREO SEL, ON 1 – 8, SOLO, REC RDY, AUTO EDIT, AUTO R/W
REWIND, FORWARD, STOP, PLAY, RECORD, LOOP, MARKER, MARKER-WRITE
UP, DOWN, LEFT, RIGHT, ZOOM
EDIT, UNDO, SAVE, FLIP, SHIFT, SCRUB
55 x 2 character LCD (backlit)
Power Adaptor (PA-300), Owner's Manual set, CD-ROM x 2, mLAN (IEEE 1394) cable
21 W
453(W) x 391(D) x 116(H) mm (including channel knobs' height)
6.2 kg
Input level
Max. before clip Actual Load Impedance
+18 dB 3 kΩ
+18 dB 3 kΩ
+18 dB 500 kΩ
Output level
Max. before clip Actual Source Impedance
+4 dBV 10 kΩ
+4 dBV 10 kΩ
8 – 40 Ω
100 mW + 100 mW
(40 Ω load)
Recommended output level
0.5 Vpp/75 Ω
SRC On/Off is possible on the
input side, Dither On/Off
possible on the output side
-
-
Other details
-
-