KX-TS600MXB / KX-TS600MXW Note: Because CONTENTS 4 is the extract from the Operating Instructions of this model, it is subject to change without notice. You can download and refer to the original Operating Instructions on TSN Server for further information.
KX-TS600MXB / KX-TS600MXW 1 ABOUT LEAD FREE SOLDER (PbF: Pb free) Note: In the information below, Pb, the symbol for lead in the periodic table of elements, will refer to standard solder or solder that contains lead. We will use PbF solder when discussing the lead free solder used in our manufacturing process which is made from Tin (Sn), Silver (Ag), and Copper (Cu).
KX-TS600MXB / KX-TS600MXW 1.2. How to recognize that Pb Free solder is used (Example: Operation P.C.B.) PQUP11371Z Marked CN801 (Component View) Note: The location of the “PbF” mark is subject to change without notice. 2 FOR SERVICE TECHNICIANS ICs and LSIs are vulnerable to static electricity.
KX-TS600MXB / KX-TS600MXW 4.5. Dial Lock 4.5.1. To Set the Dial Lock 4.5.2. To Cancel the Dial Lock Follow above steps 1 through 3. In step 3, “ “ will disappear. For Service Hint: *: If the current password is forgotten, enter “726276642” at the change password menu and you will be able to change the...
KX-TS600MXB / KX-TS600MXW 8 CIRCUIT OPERATION 8.1. Bell Detector Circuit When the bell signal is input between T/R, the signal are outputted at the speaker via the following path: Tel line → R1/C1 → D4/D3 → Pin 1 of IC1 → Pin 8 of IC1 → C6 → T1 → Speaker 8.2.
Page 19
KX-TS600MXB / KX-TS600MXW 8.3.2. Telephone Line Interface 8.3.2.1. Circuit operation • On hook Q101 is open, Q101 is connected as to cut DC loop current and cut the voice signal. • Off hook Q101 turns on thus providing an off-hook condition (active DC current flow through the circuit) and the following signal flow is for the DC loop current.
Page 20
KX-TS600MXB / KX-TS600MXW 8.3.4. Initializing Circuit 8.3.4.1. Function This circuit is used for to initialize the microcomputer when it incorporates batteries. 8.3.4.2. Circuit operation When the batteries is inserted into the unit, then the voltage is regulated by IC304 and power is supplied to the CPU. The set...
KX-TS600MXB / KX-TS600MXW 8.4. Caller ID Detect Circuit 8.4.1. Function (FSK signal) The caller ID is a changeable ID which the user of a telephone circuit obtains by entering a contract with the telephone company to utilize a caller ID service. For this reason, the operation of this circuit assumes that a caller ID service contract has been entered for the circuit being used.
KX-TS600MXB / KX-TS600MXW 9.4. EEPROM (IC802) 1. SCL SCL terminal is input terminal of Serial Clock to control transmit and receipt between Master and Slave. 2. SDA SDA terminal is input terminal, to forward the address and the mutual data between Master Device and Slave Device the mutual.
KX-TS600MXB / KX-TS600MXW 9.5. Speakerphone IC Data (IC601) Name Description A resistor to ground provides a reference current for the transmit and receive attenuators. A resistor to ground determines the nominal gain of the transmit attenuator. The transmit channel gain is inversely proportional to the RTX resistance.
KX-TS600MXB / KX-TS600MXW 10 MODULE BLOCK DIAGRAM 10.1. LCD MODULE BLOCK 10.2. CONNECTOR PIN ASSIGNMENT Pin no. Signal Function Enable +3V Power Supply — 0V Power Supply — Data Bus Line Data Bus Line Data Bus Line Data Bus Line...
KX-TS600MXB / KX-TS600MXW 11 HOW TO REPLACE THE FLAT PACKAGE IC Even if you do not have the special tools (for example, a spot heater) to remove the Flat IC, with some solder (large amount), a soldering iron and a cutter knife, you can easily remove the ICs that have more than 100 pins.
KX-TS600MXB / KX-TS600MXW 11.3. FLAT PACKAGE IC INSTALLATION PROCEDURE 1. Temporarily fix the FLAT PACKAGE IC, soldering the two marked pins. *Check the accuracy of the IC setting with the corresponding soldering foil. 2. Apply flux to all pins of the FLAT PACKAGE IC.
TS600MXW) these components, only use specified manufacture’s parts. PQHR11184Z HOLDER, NAVI KEY POM-HB PQBC10454Z2 BUTTON, OK (for KX-TS600MXB) PS-HB 3. The S mark means the part is one of some identical parts. PQBC10454Z1 BUTTON, OK (for KX-TS600MXW) PS-HB For that reason, it may be different from the installed part.
Page 35
KX-TS600MXB / KX-TS600MXW Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks Q109 2SD1819A TRANSISTOR(SI) D936 MA111 DIODE(SI) Q110 2SD1819A TRANSISTOR(SI) D940 MA111 DIODE(SI) Q201 UN5213 TRANSISTOR(SI) LED804 PSVD1SRCT Q302 2SD1819A TRANSISTOR(SI) (COILS)
Page 36
KX-TS600MXB / KX-TS600MXW Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks R312 ERJ3GEYJ104 100K R617 ERJ3GEYJ472 4.7K R313 ERJ3GEYJ103 R618 ERJ3GEYJ222 2.2K R314 ERJ3GEYJ103 R619 ERJ3GEYJ103 R320 ERJ3GEYJ103 R621 ERJ3GEYJ823 R401 ERJ3GEYJ123...
Page 37
KX-TS600MXB / KX-TS600MXW Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks C414 ECEA1CKA100 (OTHERS) C402 ECUV1C104KBV PO101 PFRT002 THERMISTOR C403 ECUV1C104KBV C404 ECUV1C104KBV 15.1.3. Operational P. C. Board Parts C405 ECUV1C104KBV C406...
KX-TS600MXB / KX-TS600MXW 16 FOR SCHEMATIC DIAGRAM 1. SW1: Hook switch. 2. SW2: Ringer selector. 3. DC voltage measurements are taken with electronic voltmeter from negative voltage line. 4. (Add 40 mA to telephone line from the loop simulator.) 5. Off-hook condition 6.