All Erase Function - JVC RD-MD5 Instructions Manual

RD-MD5(B)-e.fm Page 18 Wednesday, December 2, 1998 11:40 AM
2. Press the MD6 button and then 7 button
to set the function to MD.
The track numbers and total playback time are displayed.
3. Press the EDIT button until "ERASE ?" is
displayed.
Each time you press the button, the display changes as follows.
= =
Current display DIVIDE
=
ALL ERASE (back to the beginning)
4. Press the SET button.
Track to be erased.
5. Select the track number to be erased.
Press the 4 or ¢ button or turn the JOG dial to select the
track.
6. Press the SET button.
7. Press the ENTER button.
The selected track is erased and the number of tracks decreases
by 1. The new total track number and the total playback time ap-
pear on the display.
8. Press the 0 MD button to complete editing.
The MD is ejected after "UTOCwriting" is displayed.
• You can also complete editing operation by pressing
the button to turn off the power.
To cancel the operation, press the CANCEL button in step 4, 5,
or 6 until the display returns to the original display before editing
the track.
Note: While "UTOCwriting" is displayed, do not disconnect the
power cord or subject the Unit to the vibration to avoid in-
correct recording.
Erasing all the Tracks

(ALL ERASE Function)

Use the Unit to carry out this function.
1. Insert an MD to be edited with its label side
up.
2. Press the MD6 button and then 7 button
to set the function to MD.
The track numbers and total playback time are displayed.
3. Press the EDIT button until "ALL ERASE ?"
is displayed.
Each time you press the button, the display changes as follows.
Current display=DIVIDE=JOIN=MOVE=ERASE=ALL
ERASE=(back to the beginning)
4. Press the SET button.
= = =
JOIN MOVE ERASE
5. Press the ENTER button.
All the tracks in the MD are erased and "BLANK DISC" is kept
displayed.
6. Press the 0MD button to complete editing.
The MD is ejected after "UTOCwriting" is displayed.
• You can also complete editing operation by pressing the
button to turn off the power.
To cancel the all erasing, press the CANCEL button in step 4.
Note: While "UTOCwriting" is displayed, do not disconnect the
power cord or subject the Unit to the vibration to avoid in-
correct recording.
Giving Titles to MD (DISC TI-
TLE/TITLE Function)
You can give a disc title to the MD and a track title to the tracks in
the MD. Any title name can be given up to 32 characters using the
provided character sets.
The disc title you have given will be displayed in the following cases.
• When you insert the MD while the function is set to MD.
6
• When you press the MD button and then
function to MD.
Once you have given the title to the tracks, the track title will be dis-
played before playing the track.
Since the procedure to give title is the same as for the disc title
and track title except for step 4, both functions are explained to-
gether here.
Use the Unit to carry out these functions.
1. Insert an MD to be edited with its label side
up.
2. Press the MD6 button and then 7 button
to set the function to MD.
The total track numbers and total playback time are displayed.
3. Press the TITLE button until "DISC TITLE ?/
TITLE ? (for track title)" is displayed.
Each time you press the button, the display changes as follows.
Current display=DISC TITLE=TITLE=(back to the begin-
ning)
4. Press the SET button.
• For DISC TITLE:
Cursor
Title name area Characters to be input
• For TITLE (Track Title):
Track to be given the title
1 Select the track number to be given the title by pressing the
4 ¢
or button or turning the JOG dial.
2 Press the SET button.
Cursor
Title name area
7
button to set the
Cursor
Alternates
Cursor
Alternates
Characters to be input
18