Output/Input Set - JVC ShowView LPT0923-001A Instructions Manual

Output/Input Set

Turn on the TV and select the AV mode.
Slide the TV/CABLE/SAT/DVD switch to DVD.
ENTER
L-1 Output And L-1 Input Setting
The L-1 IN/OUT connector accepts and delivers either a composite
signal (regular video signal) or a Y/C signal (a signal in which the
luminance and chrominance signals are separated). Set "L-1
OUTPUT" and "L-1 INPUT" to the appropriate mode depending on
the type of appliance connected to the unit's L-1 IN/OUT
connector.
1
Press SET UP to access the Main Menu screen.
2
Press w e to select "FUNCTION SET UP", then press t.
3
Press w e to select "VIDEO IN/
OUT", then press t.
4
Press rt to select "L-1
OUTPUT" or "L-1 INPUT", then
press ENTER.
5
Press rt to select the
appropriate setting, then press
ENTER.
6
Press SET UP to complete the
setting.
* The boldface settings below
indicate the settings at your
purchase.
8 L-1 OUTPUT — SCART VIDEO / SCART S-VIDEO / SCART
RGB / COMPONENT
SCART VIDEO
: If a connected appliance's input is compatible only
with regular video signals, set to "SCART VIDEO".
SCART S-VIDEO
: If a connected appliance's input is compatible
with Y/C signals, set to "SCART S-VIDEO". You can obtain high-
quality picture. (For connection, be sure to use a 21-pin SCART
cable that is compatible with the Y/C signal.)
SCART RGB
: If a connected appliance's input is compatible with
RGB signals, set to "SCART RGB". You can obtain a high-quality
RGB picture.
CABLE/SAT
TV DVD
rtwe
SET UP
DVD VIDEO SET UP HDD/DVD SET UP FUNCTION SET UP INITIAL SET UP
REC/PLAY SET UP DISPLAY SET VIDEO IN/OUT
MONITOR TYPE 4 : 3LB
F-1 INPUT VIDEO
L-1 OUTPUT SCART VIDEO
L-1 INPUT VIDEO
L-2 SELECT
VIDEO
SET UP ENTER
SELECT WITH [ ] THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
EXIT SELECT
DVD VIDEO SET UP HDD/DVD SET UP FUNCTION SET UP INITIAL SET UP
REC/PLAY SET UP DISPLAY SET VIDEO IN/OUT
MONITOR TYPE 4 : 3LB
F-1 INPUT VIDEO
L-1 INPUT SCART VIDEO
L-1 OUTPUT VIDEO
SCART VIDEO
SCART S-VIDEO
L-2 SELECT VIDEO
SCART RGB
COMPONENT
SET UP ENTER
SELECT WITH [ ] THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
EXIT
SELECT
COMPONENT
: If a connected appliance's input is compatible with
Y/PB/PR signals, set to "COMPONENT". You can obtain a high-
quality Y/PB/PR picture. Switch the TV to the input that you can
watch component video pictures.
8 L-1 INPUT — VIDEO / S-VIDEO
VIDEO
: If a connected appliance's output is compatible only with
regular video signals, set to "VIDEO".
S-VIDEO
: If a connected appliance's output is compatible with Y/C
signals, set to "S-VIDEO". You can obtain a high-quality picture.
(For connection, be sure to use a 21-pin SCART cable that is
compatible with the Y/C signal.)
NOTES:
If "L-1 OUTPUT" is set to "SCART S-VIDEO", "SCART RGB" or
"COMPONENT", it is not possible to set "L-1 INPUT" to "S-VIDEO".
If "L-2 SELECT" is set to "DECODER", it is not possible to set "L-1
INPUT" to "S-VIDEO".
If "L-2 SELECT" is set to "DECODER", it is only possible to set "L-1
OUTPUT" to "SCART VIDEO".
Component video signals are not output from the L-1 IN/OUT
connector.
When Progressive scan mode is engaged, it is not possible to select
the setting of "L-1 OUTPUT". (
L-2 Select Setting
Set "L-2 SELECT" to the appropriate mode depending on the type
of appliance connected to the unit's L-2 IN/DECODER connector.
1
Perform steps 1 and 2 of "L-1 Output And L-1 Input Setting" on
the left column.
2
Press rt to select "L-2 SELECT", then press ENTER.
3
Press rt to select the
appropriate setting, then press
ENTER.
4
Press SET UP to complete the
setting.
* The boldface settings below
indicate the settings at your
purchase.
8 L-2 SELECT — VIDEO / S-VIDEO / SAT VIDEO / SAT
S-VIDEO / DECODER
Select "VIDEO" or "S-VIDEO" to use this unit as the recording deck
with the player connected to the L-2 IN/DECODER connector, or to
use the satellite receiver connected to the L-2 IN/DECODER
connector.
VIDEO
: If a connected appliance's output is compatible only with
regular video signals, set to "VIDEO".
S-VIDEO
: If a connected appliance's output is compatible with Y/C
signals, set to "S-VIDEO". You can obtain high-quality picture.
(For connection, be sure to use a 21-pin SCART cable that is
compatible with the Y/C signal.)
Select "SAT VIDEO" or "SAT S-VIDEO" to view a satellite
programme with the TV set while the unit is turned off. (
SAT VIDEO
: If a connected satellite receiver's output is compatible
only with regular video signals, set to "SAT VIDEO".
SAT S-VIDEO
: If a connected satellite receiver's output is
compatible with Y/C signals, set to "SAT S-VIDEO". You can
obtain a high-quality S-VHS picture. (For connection, be sure to
use a 21-pin SCART cable that is compatible with the Y/C signal.)
DECODER
: To use a decoder connected to the L-2 IN/DECODER
connector.
EDITING
EN
pg. 69)
DVD VIDEO SET UP HDD/DVD SET UP FUNCTION SET UP INITIAL SET UP
REC/PLAY SET UP DISPLAY SET VIDEO IN/OUT
MONITOR TYPE 4 : 3LB
F-1 INPUT VIDEO
L-1 INPUT VIDEO
L-1 OUTPUT SCART VIDEO
L-2 SELECT VIDEO
SAT VIDEO
SAT S-VIDEO
DECODER
SET UP ENTER
SELECT WITH [ ] THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
EXIT SELECT
pg. 65)
61
VIDEO
S-VIDEO