Manual Timer Programing - JVC DR-MH20S Instructions Manual

TIMER RECORDING
48
EN

Manual Timer Programing

You can program this unit to timer-record as many as 32 programs.
If you do not know the VCR Plus+ number for the program you
wish to record, use the following procedure to set your unit to
timer-record the program.
Make sure that the unit's built-in clock is set properly.
Turn on the unit.
Turn on the TV and select the AV mode.
Slide the TV/CABLE/DBS/DVD switch to DVD.
AUX
ENTER
1
Load a recordable disc if recording to DVD.
2
Press PROGRAM to access the program top screen.
3
Press rtw e to select "CALENDAR PR.", then press ENTER.
When "PROGRAM FULL DELETE UNWANTED TIMER
PROGRAMS" appears on the TV screen, you need to cancel some of
the reserved programs. (
4
Press rtw e to select the desired date, then press ENTER.
5
Press rt to select "RECORD
TO", then press ENTER. Press
rt to select the desired
recording deck, then press
ENTER.
CABLE/DBS
TV DVD
PROGRAM
rtwe
pg. 49)
2 PROGRAM > CALENDAR PROG. (2/3)
01/08/03 WED 10:30PM - 11:00PM
RECORD TO
SELECT WITH [ ]
THEN PRESS [ENTER]
START
PRESS [PROGRAM]
STOP
TO EXIT
SOURCE
CH
PROGRAM ENTER
EXIT SELECT
6
Press rt to select "START", then press ENTER. Press rt to
set the desired start time, then press ENTER.
Each press of rt advances/goes back the start time in 1-min.
increments.
To advance/go back the start time in 30-min. increments, press and
hold rt.
7
Press rt to select "STOP", then press ENTER. Press rt to
set the desired stop time, then press ENTER.
Each press of rt advances/goes back the stop time in 1-min.
increments.
To advance/go back the stop time in 30-min. increments, press and
hold rt.
8
Press rt to select "SOURCE", then press ENTER. Press rt
to select the desired source, then press ENTER.
9
Press rt to select "CH", then press ENTER. Press rt to
select the desired channel.
10
Press rt to select "CONFIRM", then press ENTER.
11
Set the other recording options as required.
Refer to step 8 in "VCR Plus+
12
Press rt to select "OK",
then press ENTER to access the
Program Confirmation screen.
13
Press w e to select "EXIT",
then press ENTER to complete
timer programing.
To program another timer, press
w e to select "CONTINUE",
then press ENTER.
If "PROGRAM OVERLAPPED" appears on the TV screen, see
page 49.
NOTES:
When two successive programs are recorded on a DVD-RW disc with
Manual Timer Programing function, the beginning of the second one
may be left off the recording.
If the copy limited program is received during timer-recording, the unit
enters Record Pause mode. Recording starts again if it is switched to
a recordable broadcast during the time you programed.
Cable Box and DBS Receiver Users
To timer-record a satellite broadcast using Manual Timer
Programing:
A Perform "Cable Box and/or DBS Receiver Control Setting"
( pg. 24).
B Perform "Manual Timer Programing" (
C Leave the cable box or DBS receiver's power on.
DBS 100
[MISC. ] XP
Relief Recording
HDD
When a program that is set for the DVD deck cannot be recorded
10:30PM
properly, the program is recorded to the HDD deck instead in the
11:00PM
DBS
same recording mode as set.
100
If the remaining capacity of the hard disc is not sufficient, the
O K
program is recorded to the DVD deck until the remaining capacity
of the DVD disc lasts.
If "JUST" is selected for the recording mode, the current recording
mode for the DVD deck is applied.
® Timer Programing" ( pg. 46).
2
PROGRAM > CALENDAR PROG. (3/3)
01/08/03 WED 10:30PM - 11:00PM
GARDENING
INPUT TITLE
SELECT WITH [ ]
THEN PRESS [ENTER]
CATEGORY
PRESS [PROGRAM]
WEEKLY/DAILY MON-FRI (FOR A WEEK)
TO EXIT
REC MODE
PROGRAM ENTER
O K
EXIT SELECT
pg. 48).
DBS 100
[EDUCATION] FR360
1:00 28:00
GARDENING
EDUCATION
FR360