Table of Contents
Advertisement
Filename [MV5S_08Basic TimerDub.fm]
MV5S_00.book Page 31 Wednesday, August 31, 2005 4:55 PM
Manual Timer Programming
You can programme each deck to timer-record as many as
8 programmes up to 30 days ahead.
If you do not know the S
V
HOW
IEW
wish to record, use the following procedure to set your unit to
timer-record the programme.
Make sure that the unit's built-in clock is set properly.
Turn on the unit.
Turn on the TV and select the AV mode.
Slide the TV/DVD switch to DVD.
VHS
PROG
ENTER
Satellite Receiver Users (DVD Deck Only)
To timer-record a satellite broadcast using Manual Timer
Programming:
A Perform "Manual Timer Programming".
B Set the satellite receiver to the appropriate channel before
the selected programme begins.
C Select "L-2" in step 8.
D Leave the satellite receiver's power on.
NOTES:
When two successive programmes are recorded on a DVD-RW disc
with Manual Timer Programming function, the beginning of the
second one may be left off the recording.
If the copy limited programme is received during timer-recording, the
unit enters Record Pause mode. Recording starts again if it is
switched to a recordable broadcast during the time you programmed.
In case of a power failure after programming, the unit's memory
backup keeps your selections for approximately 10 minutes.
Programmes that start after midnight must have the next day's date.
To record the programmes received by the satellite receiver, record
on the DVD discs. For details, refer to "Satellite Receiver Users (DVD
Deck Only)" above.
Page 31Wednesday, 31 August 2005 16:55
number for the programme you
DVD
TIMER
rtwe
Masterpage:Right+
1
Press DVD or VHS to select the deck on which you want to
perform timer programming.
2
For DVD deck
Load a recordable disc.
For VHS deck
Load a cassette with safety tab intact.
3
Press PROG to access the
Programme Check screen.
4
For DVD deck
Press rt w e to select "DVD"
and press rt to select "NEW
TIMER PROGRAMME", then
press ENTER.
For VHS deck
Press rt w e to select "VHS"
and press rt to select "NEW
TIMER PROGRAMME", then
press ENTER.
5
Press rt to set the desired
date.
The current date appears on the
TV screen. The date you enter
appears in its place.
6
Press w e to select "START", then press rt to set the desired
start time.
Each press of rt advances/goes back the start time in 1-min.
increments.
To advance/go back the start time in 30-min. increments, press and
hold rt.
7
Press w e to select "STOP", then press rt to set the desired
stop time.
Each press of rt advances/goes back the stop time in 1-min.
increments.
To advance/go back the stop time in 30-min. increments, press and
hold rt.
8
Press w e to select "TV PROG", then press rt to select the
desired channel.
9
Press w e to select the desired recording option as required.
Refer to step 6 in "S
V
™ Timer Programming" (
HOW
IEW
10
Press ENTER to access the Programme Confirmation screen.
11
Press ENTER to complete timer programming.
To programme another timer, repeat steps 3 – 11.
If "PROGRAMME OVERLAPPED" appears on the TV screen, see
page 35.
12
Press TIMER # to engage the unit's timer mode. The DVD
timer indicator lights up on the unit and the unit is automatically
turned off.
To disengage the timer mode, press TIMER # again.
TIMER RECORDING
31
EN
VHS
DVD
DATE
START-STOP TV PROG
DAILY/WEEKLY
VPS/PDC REC MODE
WEEKLY
ON
05/07 SAT
19:00 - 20:00
44
SP
ON
10/07 THU
22:00 - 22:30
10
XP
11/07 FRI
26
OFF
LP
13:30 - 14:00
11/07 FRI
16:00 - 17:00
33
OFF
LP
++++++++++++++++ NEW TIMER PROGRAMME ++++++++++++++++
DISC TIMER PRGM
EXIT
OK
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
SELECT
PROG
TIMER PROGRAMME
DATE
START
STOP
TV PROG
05/07 SAT
20:00
20:30
VTM 10
DAILY/WEEKLY
VPS/PDC
REC MODE
NAME
OFF
LP
EXIT
CONFIRM
SET TIMER PROGRAMMING WITH [CURSORS]
THEN PRESS [ENTER]
SELECT
PROG
pg. 29).
Advertisement
Table of Contents
