Manual Timer Programming - JVC DR-MV5SE Instructions Manual

Manual Timer Programming

You can programme each deck to timer-record as many as
8 programmes up to 30 days ahead.
If you do not know the S
HOW
wish to record, use the following procedure to set your unit to
timer-record the programme.
Make sure that the unit's built-in clock is set properly.
Turn on the unit.
Turn on the TV and select the AV mode.
Slide the TV/DVD switch to DVD.
VHS
PROG
ENTER
Satellite Receiver Users (DVD Deck Only)
To timer-record a satellite broadcast using Manual Timer
Programming:
A Perform "Manual Timer Programming".
B Set the satellite receiver to the appropriate channel before
the selected programme begins.
C Select "L-2" in step 8.
D Leave the satellite receiver's power on.
NOTES:
When two successive programmes are recorded on a DVD-RW disc
with Manual Timer Programming function, the beginning of the
second one may be left off the recording.
If the copy limited programme is received during timer-recording, the
unit enters Record Pause mode. Recording starts again if it is
switched to a recordable broadcast during the time you programmed.
In case of a power failure after programming, the unit's memory
backup keeps your selections for approximately 10 minutes.
Programmes that start after midnight must have the next day's date.
To record the programmes received by the satellite receiver, record
on the DVD discs. For details, refer to "Satellite Receiver Users (DVD
Deck Only)" above.
V number for the programme you
IEW
DVD
TIMER
rtwe
1
Press DVD or VHS to select the deck on which you want to
perform timer programming.
2
For DVD deck
Load a recordable disc.
For VHS deck
Load a cassette with safety tab intact.
3
Press PROG to access the
Programme Check screen.
When "PROGRAMME FULL
DELETE UNWANTED TIMER
PROGRAMME" appears on the
TV screen, you need to cancel
some of the reserved
programmes. ( pg. 34)
4
For DVD deck
Press rt w e to select "DVD PRGM CHECK" and press rt to
select "DVD NEW TIMER PROGRAMME", then press ENTER.
For VHS deck
Press rt w e to select "VHS
PRGM CHECK" and press rt to
select "VHS NEW TIMER
PROGRAMME", then press ENTER.
5
Press rt to set the desired date.
The current date appears on the
TV screen. The date you enter
appears in its place.
6
Press w e to select "START",
then press rt to set the desired start time.
Each press of rt advances/goes back the start time in 1-min.
increments.
To advance/go back the start time in 30-min. increments, press and
hold rt.
7
Press w e to select "STOP", then press rt to set the desired
stop time.
Each press of rt advances/goes back the stop time in 1-min.
increments.
To advance/go back the stop time in 30-min. increments, press and
hold rt.
8
Press w e to select "TV PROG", then press rt to select the
desired channel.
9
Press w e to select the desired recording option as required.
Refer to step 6 in "S V
HOW IEW
10
Press ENTER to access the Programme Confirmation screen.
11
Press ENTER to complete timer programming.
To programme another timer, repeat steps 3 – 11.
If "PROGRAMME OVERLAPPED" appears on the TV screen, see
page 35.
12
Press TIMER # to engage the unit's timer mode. The DVD
timer indicator lights up on the unit and the unit is automatically
turned off.
To disengage the timer mode, press TIMER # again.
TIMER RECORDING
VHS PRGM CHECK DVD PRGM CHECK
DATE START-STOP TV PROG DAILY/WEEKLY
05/07 SAT 44 WEEKLY
19:00 - 20:00
10/07 THU 10
22:00 - 22:30
11/07 FRI 26
13:30 - 14:00
16:00 - 17:00
11/07 FRI 33
+++++++++++++++++ DVD NEW TIMER PROGRAMME +++++++++++++++++
DISC TIMER PRGM
EXIT
OK
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
SELECT
PROG
TIMER PROGRAMME
DATE START STOP
05/07 SAT 20:00 20:30
DAILY/WEEKLY VPS/PDC REC MODE
OFF LP
EXIT CONFIRM
SET TIMER PROGRAMMING WITH [CURSORS]
THEN PRESS [ENTER]
SELECT
PROG
™ Timer Programming" ( pg. 29).
31
EN
VPS/PDC REC MODE
ON SP
ON XP
OFF LP
OFF
LP
TV PROG
VTM 10
NAME