Dv Dubbing - JVC DR-MH20SUJ Instructions Manual

Filename [DR-MH30UJ_09Editing.fm]
DR-MH30UJ_00.book Page 60 Monday, July 12, 2004 3:17 PM
EDITING
60
EN

DV Dubbing

You can dub programs from a camcorder or DV equipment
connected to the unit with a DV cable. The unit's remote control
allows you the limited control of the connected camcorder or DV
equipment functions during dubbing.
NOTES:
Use the DV cable VC-VDV 204U for connection.
When you connect a PC to the DV IN connector, we do not assure
the normal operation of this unit.
Your unit
Camcorder
DV equipment
1
Connect a camcorder or DV equipment to the DV IN connector
on the unit's front panel.
2
Press HDD.
3
Press CH +/– to set the channel to "DV".
4
Press ON SCREEN.
The on-screen display for DV dubbing appears.
5
Press w e to select
the remote icon (facing to the right) for the DV equipment.
6
Press w e to select
, then press ENTER
repeatedly until the desired sound
track appears on the TV screen.
AUDIO 1
: Select this to record the
original stereo sound played
back on the connected DV
equipment.
AUDIO 2
: Select this to record the
dubbed stereo sound played back on the connected DV
equipment.
MIX
: Select this to record the sound of both "AUDIO 1" and
"AUDIO 2".
Note that this selection is not available when the source program is
recorded in 16BIT (48 kHz) mode.
7
Press REC MODE repeatedly to set the recording mode.
Page 60
DV IN connector
DV cable
(VC-VDV 204U)
(not provided)
DV connector
, then press ENTER to display
0:00 1:00 2:00
DV
HDD GR-DV3500
00:00:00. 00 00:00:00. 00 L – R
FR360
12bit DV JVC GR-DV3500 SOUND1
1 2
DV DV
8
Locate the point from where you want to start dubbing, then
stop or pause playback by pressing the following buttons on the
remote control: 4, 5, 3, 8, 9
To play back in slow speed (1/10 of the normal speed), press 9 to
pause playback, then press 3 or 5.
To play back frame-by-frame, press 9 to pause playback, then press
9 repeatedly. Each press of 9 advances a frame.
To change the playback direction, press 3 or 5.
9
Press w e to select
dubbing starts.
Playback on the external DV equipment and recording on the unit
should start simultaneously.
To pause dubbing, press w e to select
ENTER. Both the unit and the external DV equipment pause dubbing.
Pressing 9 on the unit also works the same way.
10
Press w e to select
press 8. The DV equipment stops.
11
Press w e to select
12
Press 8 twice on the remote control to stop dubbing.
Both the unit and the external DV equipment stop dubbing.
NOTES:
Dubbing copyright guarded programs is not possible.
Original DV informations such as the recording date and time are not
recorded.
The superimposed indication during the operation or dubbing is not
recorded.
If the dubbing is paused while the channel is set to "DV", you cannot
switch channels.
When you dub from DV equipment other than a
camcorder
A Perform step 1 to 4.
B Locate the point from where you want to start dubbing,
then stop on the DV equipment.
If you pause the DV equipment in this step, a few second's
still picture will be recorded at the beginning of the recorded
program.
C Set the input mode to "DV INPUT" on the DV equipment.
If you select an input mode other than "DV INPUT", unwanted
pictures may be recorded at the beginning of the recorded
program.
D Perform step 9 to 12.
To skip unwanted part of the source picture
Press ENTER to stop both equipment, then press w e to select
.
Locate the point where you want to restart dubbing by pressing 4,
5, or 3, then press 8.
Press w e to select
dubbing.
Masterpage:Left+
, then press ENTER. The
, then press
, then press ENTER. Then
, then press ENTER.
, then press ENTER to restart
Monday, 12 July 2004 14:25