Before Requesting Service - Panasonic PV-455S-K Operating Instructions Manual

Before Requesting Service

Check the following points once again if you are having trouble with your VCR.
(BO : refers to "Basic Operations" Instruction book.)
(AO : refers to "Advanced Operations" Instruction book.)
Power
No power...
Recording & Playback
TV program cannot be recorded...
Timer recording cannot be
performed...
There is no playback picture, or the
playback picture is noisy or contains
streaks...
Special effects playback picture
may contain some vertical jitter
when using a TV with an Automatic
Vertical Hold Control...
VCR cannot be controlled...
Remote Control
VCR cannot be remote controlled...
ACTION and PROG buttons do not
respond...
Miscellaneous
Programs cannot be viewed on TV...
Video cassette cannot be inserted...
Video cassette cannot be removed...
Video cassette ejects when a
recording is started or the power is
turned off for timer recording...
In Stop mode, the motor
(CYLINDER) continues to rotate...
Correction
• Completely insert Power Plug into an AC outlet.
• Press POWER button on.
• Make sure power source is active.
Correction
• Check connections between VCR, external antenna, and
TV.
• Check connections selection. (BO p. 4, AO p. 3)
• Make sure your antenna system (CABLE or TV) is correctly
set. (Channels [BO p. 11])
• Make sure cassette record tab is intact. (BO p. 3)
• Confirm that clock is set to current time and date.
• Make sure Cable/DSS box (if used) is left on and tuned to
channel to be recorded.
• Set recording start/stop times correctly. (BO p. 6, 7)
• Make sure VCR POWER button is pressed off. (BO p. 6, 7)
• Timer recording may not be performed or continued if a
power interruption occurs before or during a Timer
Recording, even after power is restored.
• Select channel 3 or 4 on TV to match VCR output channel
(3 or 4) (BO p. 4) or select LINE.
• Set VCR/TV selector to "VCR."
• Adjust TRACKING control in either direction. (BO p. 3)
• Try Head Cleaning. (BO p. 3)
• Set TV's Vertical Hold Control to MANUAL, then adjust.
• Make sure VCR power is on.
• Check Remote batteries.
• Make sure VCR LOCK is set to off. (AO p. 10)
• Make sure Timer Record is not in progress.
Correction
• Make sure VCR power is on.
• Make sure Remote is in VCR mode.
• Aim Remote Control directly at remote sensor on VCR.
(BO p. 10)
• Avoid any object blocking signal path.
• Check Remote batteries. (BO p. 3)
• Make sure VCR LOCK is set to off. (AO p. 10)
• Exposing VCR remote sensor to direct fluorescent or
outdoor light may cause signal interference.
• Check connections between VCR, external antenna, and
TV.
• Press VCR button for VCR mode. (AO p. 2)
• Check Remote batteries. (BO p. 3)
Correction
• Make sure TV power is on.
• Make sure TV is tuned to VCR's output channel (3 or 4).
• Check connections between VCR, external antenna, and
TV.
• Set VCR/TV selector to "TV." (BO p. 5, AO p.10)
• Make sure proper signal source is selected.
• Insert the cassette with window side up; record tab facing
you.
• Check if a tape is already in the unit.
• Confirm Power Plug is fully inserted into an AC outlet.
• Make sure cassette record tab is intact. (BO p. 3)
• To enable Quick play mechanism, the cylinder will rotate for
about 5 minutes. This reduces response time from Stop to
Play mode and from Play to Rewind Search mode.
- 12 -