Related Manuals for ClearSounds CS2000M
Summary of Contents for ClearSounds CS2000M
- Page 1 OWNER'S MANUAL WIRELESS TV LISTENING SYSTEM with Dual Ear Volume Control Model CS2000M 95 KHz Frequency...
-
Page 2: Table Of Contents
In-Warranty Procedure . . . . . . . .11 television has before setting up your ClearSounds® CS2000M. NOTE: CS2000M is not suitable for use with Plasma and LCD flat screen TVs. If you are having any difficulty, please... -
Page 3: How It Works
HOW IT WORKs The transmitter sits on your audio source them back into sound. You adjust (TV/VCR, stereo, etc.) and transmits the volume on the cordless head- an audio signal via infrared light. The phones to suit your personal needs. receiver in the headphones captures Multiple headphones can be used the infrared light waves and converts... -
Page 4: Installation
INsTALLATION How you install your CS2000M of your television speakers, you must will depend on what type of equip- either use the microphone adaptor or connect the Transmitter to your VCR ment you have. To determine which (see VCR installation below). - Page 5 the adaptor to the audio output and not Diagram 1 DC in 12 Volt the video output. Power Mono Installation – for use with TVs, VCRs, or stereos that have only one audio output jack. Standard Installation – for use with Connect the Transmitter (A) to the RCA TVs, VCRs, or stereos that have 3.5mm Mono Adaptor Cord (F) and...
- Page 6 it into the headphone jack as indicated in Small Headphone Jack Installation – Diagram 5. for use with equipment that has a small headphone jack. Connect Diagram 5 the Transmitter (A) directly into the equipment’s audio output jack as shown in Diagram 4. Diagram 4 or TAPe PLAYeR Large...
- Page 7 jacks on the VCR. If your VCR has one over the speaker by peeling the tape audio output jack, use the RCA 3.5mm off the back of the adhesive. For Mono Adaptor (F) instead of (D). See this installation you will have to Diagram 6.
-
Page 8: Placement Of Transmitter
PLACeMeNT OF THe and negative to negative. Turn on the head- phones making sure there is an unobstructed TRANsMITTeR line of sight between the headphones and the Transmitter. Adjust the television vol- Turn on the Infrared Transmitter ume and the headphone volume to a com- (A). -
Page 9: Troubleshooting
TROUBLesHOOTING probLem possibLe CAUse - AC Adaptor is not plugged in red power light - AC plug is not plugged into the transmitter is not on - The audio cord is not plugged into the audio source - There is no audio output from the audio source - The audio cord is not plugged into the audio source no sound from - There is no audio output from the audio source... -
Page 10: Technical Specifications
TeCHNICAL sPeCIFICATIONs Transmission Mode ....Infrared 940 nanometers Frequency Modulation (2.3 and 2.8MHz) Operating Voltage ....Transmitter - 12 VDC via 120 VAC, 60 Hz AD/DC adaptor Frequency Response . -
Page 11: Limited Warranty
Center listed below. you.) This warranty does not cover (1) A defect that has been caused by repair NOTE: Prior to returning any CS2000M or modifications; (2) A defect caused ® to the ClearSounds... - Page 12 Need Help Hearing On The Telephone? Visit: www.clearsounds.com 8160 S. Madison Street Burr Ridge, IL 60527 Tel: 1-800-965-9043 / TTY: 1-800-814-5369 © 2007 ClearSounds P/N: R907770121...