Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Fujitsu Siemens Computers D1808
Summary of Contents for Fujitsu Siemens Computers D1808
- Page 1 Component English Technical Manual Mainboard D1808...
- Page 2 Are there ..any technical problems or other questions you need clarified? Please contact: ● your sales partner ● your sales outlet The latest information and updates (e. g. BIOS update) on our mainboards can be found on the Internet under: http://www.fujitsu-siemens.com...
- Page 4 Questo manuale è stato stampato su carta da riciclaggio. Denna handbok är tryckt på recyclingpapper. Dit handboek werd op recycling-papier gedrukt. Herausgegeben von/Published by Fujitsu Siemens Computers GmbH Bestell-Nr./Order No.: A26361-D1808-Z120-1-7619 Ausgabe/Edition 1 Printed in the Federal Republic of Germany...
- Page 5 English Mainboard D1808 Technical Manual July 2006 edition 1...
- Page 6 All other trademarks referenced are trademarks or registered trademarks of their respective owners, whose protected rights are acknowledged. Copyright © Fujitsu Siemens Computers GmbH 2006 All rights, including rights of translation, reproduction by printing, copying or similar methods, even of parts are reserved.
-
Page 7: Table Of Contents
Central Processor Unit (CPU) Considerations ..................6 Memory Considerations........................6 Power Supply Considerations ......................7 Board Installation ..........................8 Overview Mainboard D1808 ......................... 8 Fan Connector (FANx) ......................... 9 Chassis Intrusion (INTR) ......................9 PC2004 PSU Connector (PC2004) ....................9 CD-In and AUC-IN (CD / AUX).................... - Page 8 Contents A26361-D1808-Z120-1-7619, Edition 1...
-
Page 9: Mainboard D1808
You have purchased one of the most powerful Intel Xeon®-based workstation solutions in a standard SSI EEB v3.5 form factor. Based on the Intel® 5000X chipset, the D1808 features some state-of-the-art technologies such as dual/single 1333 and 1066 MHz FSB Dual-Core Xeon® Processor 5100 Series support, multiple PCI-Express buses, quad channel DDR2 FB-DIMM memory design, onboard Dual-Port PCI-Express Gigabit Ethernet, SATA ports, SAS ports and multiple USB2.0 (Universal Serial Bus) ports. -
Page 10: Important Notes
The equipment and tools you use must be free of static charges. ● Remove the power plug from the mains supply before inserting or removing boards containing ESDs. ● Always hold boards with ESDs by their edges. ● Never touch pins or conductors on boards fitted with ESDs. A26361-D1808-Z120-1-7619, edition 1... -
Page 11: Hardware Specifications
Two ports 400Mbit ● One UART serial port connector ● One ECP/EPP/SPP parallel connector Trusted Platform Management (TPM) ● Eight USB2.0 ports (4 USB ports via ● Infineon SLB9635TT 1.2 header) ● PS/2 mouse & keyboard ports A26361-D1808-Z120-1-7619, edition 1... -
Page 12: Software Specifications
● FCC Class B (Declaration of Conformity) ● European Community CE (Declaration of Conformity) Fujitsu Siemens Computers reserves the right to add support or discontinue support for any OS with or without notice. Software Specifications OS (Operating System) Support ●... -
Page 13: Board Diagram
The above picture is purely representative. Due to engineering updates and new board revisions, certain components may change and or be repositioned. The picture above may or may not look exactly like the board you received. The following page includes details on the vital components of this motherboard. A26361-D1808-Z120-1-7619, edition 1... -
Page 14: Choose Proper Parts For Your System
Single/Dual Processor System D1808 board supports one or two Dual-Core Intel® Xeon® Processors. Single Processor System: When only install a single processor on D1808, the processor must be installed in the CPU0 socket. Dual Processor System: D1808 supports dual processor configurations only in which both processors operate with the same FSB frequency, core frequency, and have the same internal cache sizes. -
Page 15: Power Supply Considerations
● Power connectors D1808 is powered by a split plane PSU with four +12V-rails and 700W continuous power. One rail is for each processor, one for systemboard and one for peripherals (e.g. HHDs, add. 6-pin graphics connector). There are three power connectors on this motherboard as listed below. -
Page 16: Board Installation
Board Installation Board Installation Overview Mainboard D1808 FAN 2 FLOPPY SATA 2 SATA 3 SATA 4 SATA 5 SAS3 SAS2 SAS1 SAS0 PCI FAN CD IN AUXIN JP14 20 19 18 1 = PS/2 Wakeup Enable/Disable (PS2 PWR) 12 = Clear CMOS Switch (CMOS) -
Page 17: Fan Connector (Fanx)
Pin4: Fan PWM (speed) Control This 4-pin fan connector supports tachometer monitoring. There are five 4-pin fan connectors on D1808. Use these connectors to connect chassis and processor cooling fans to your motherboard. Cooling fans can keep the system stable and reliable for its product’s life. -
Page 18: Cd-In And Auc-In (Cd / Aux)
Normally, a chassis has some control or signal wires can be connected onto a motherboard for hard drive LED, Power LED, power button, and reset button; The front panel header has been implemented on D1808 for such purposes. Signal Signal... -
Page 19: Lcd Header (Lcd)
HDA compliant Front Panel Audio Header (AUDIO - yellow) Signal Signal PORT1-L Analog GND PORT1-R Presence Detect PORT2-R PORT1 Sens Return Jack Sens Send PORT2-L PORT2 Sens Return IEEE 1394 Header (FRNT1394 – grey) Signal Signal TPA+ TPA- TPB+ TPB- P12VP P12VP A26361-D1808-Z120-1-7619, edition 1... - Page 20 PS/2 Wakeup Enable/Disable (PS2 PWR) Close Pin-1 and 2 no PS/2 device wakeup Close Pin- 2 and 3 – enables PS/2 device wakeup (Default) BIOS Write Protect (PROT) Open – FWH can be written (Default) Closed – FWH write protection A26361-D1808-Z120-1-7619, edition 1...
-
Page 21: Installing The Memory
Installing the Memory Before attempting to install any memory, make sure that the memory you have is compatible with the motherboard as well as the processor. The D1808 board supports up to eight 240-pin 1.8-Volt DDR2-667/533 ECC FB-DIMM modules. Here are a few key points to note before installing memory into your D1808: ●... -
Page 22: Memory Installation Procedure
Push the holders on each side of the memory slot outwards. ► Insert the memory module into the location (1). ► At the same time flip the lateral holders upwards until the memory module snaps in place (2). A26361-D1808-Z120-1-7619, edition 1... - Page 23 You must unplug the power connector to the motherboard before performing system hardware changes, to avoid damaging the board or expansion device. A26361-D1808-Z120-1-7619, edition 1...
-
Page 24: Installing The Processor And Heatsink
Installing the processor The processor socket ist covered with a protective cap to protect the spring contacts In a warranty case the mainboard can only be taken back by Fujitsu Siemens Computers with the protective cap secured! Never touch the underside of the processor. Even minor soiling such as grease from the skin can impair the processor's operation or destroy the processor. - Page 25 (a). ► Fold down the frame (1). ► Press the lever downward (2) until it is hooked in again. ► Remove the protective cap (3) and keep it. A26361-D1808-Z120-1-7619, edition 1...
-
Page 26: Mounting Heat Sink
► Secure the heat sink - depending on the model - with four screws or push it into the mounts. A26361-D1808-Z120-1-7619, edition 1... -
Page 27: Installing Add-In Cards
This allows air to more easily circulate within the chassis, providing improved cooling for all installed devices. You must unplug the power connector to the motherboard before performing system hardware changes, to avoid damaging the board or expansion device. A26361-D1808-Z120-1-7619, edition 1... -
Page 28: Connecting External Devices
While the ports have been created to accept connectors in only one direction, make sure to be careful when inserting connectors. At times, attaching connectors in the incorrect orientation can damage, bend and or break the pins. A26361-D1808-Z120-1-7619, edition 1... -
Page 29: Installing The Power Supply
(only for use with this workstation) one 4-pin molex-type connector (P19) – one yellow wire, one red wire and two black wires (only for use with a server from Fujitsu Siemens Computers) two 6-pin connectors for graphic adapters (P10, P11) -
Page 30: Replacing Lithium Battery
Press the catch in the direction of the arrow (1). The battery jumps out of the holder slightly. ► Remove the battery (2). ► Push the new lithium battery of the identical type into the holder (3) and press it downward until it engages (4). A26361-D1808-Z120-1-7619, edition 1... -
Page 31: Bios Update
Board Installation BIOS update When should a BIOS update be carried out? Fujitsu Siemens Computers makes new BIOS versions available to ensure compatibility to new operating systems, new software or new hardware. In addition, new BIOS functions can also be integrated. -
Page 32: Bios Recovery
Start the PC and invoke BIOS Setup. ► Select the menu item Reset configuration in the menu Advanced and change the setting to Yes. ► Save the change and terminate BIOS Setup. The BIOS recovery has now been completed. The system restarts. A26361-D1808-Z120-1-7619, edition 1... -
Page 33: Glossary
I/O Controller Hub Trusted Platform Module Intelligent Drive Electronics UDMA Ultra DMA Input/Output Universal Serial Bus Initial Program Load Video Graphic Adapter IPSEC Internet Protocol Security Zero Channel Raid Industrial Standard Architecture ZIF Socket Zero Insertion Force socket A26361-D1808-Z120-1-7619, edition 1... - Page 34 Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by manufacturer. Dispose of used battery according to manufacturer instructions and in accordance with your local regulations. A26361-D1808-Z120-1-7619, edition 1...