Operating Instructions - Napoleon The Dream BGD90NT Installation And Operation Instructions Manual

24
FOR YOUR SAFETY READ BEFORE
LIGHTING:
A. This fi replace is equipped with a pilot which must be
lit by hand while following these instructions exactly.
B. Before operating smell all around the fi replace area
for gas and next to the fl oor because some gas is
heavier than air and will settle on the fl oor.
C. Use only your hand to turn the gas control knob /
manual shut-off knob. Never use tools. If the knob
will not turn by hand, do not try to repair it. Call a
qualifi ed service technician. Force or attempted re
pair may result in a fi re or explosion.
D. Do not use this fi replace if any part has been under
water. Immediately call a qualifi ed service technician
to inspect the fi replace and replace any part of the
control system and any gas control which has been
under water.
LIGHTING INSTRUCTIONS
Warning: if you do not follow these instructions exactly,
a fi re or explosion may result causing property damage,
personal injury or loss of life. Initial lighting of the pilot and
main burners must be done with the glass door off.
Do not connect valve or wall switch to electricity. See
installation instructions.
When lighting and re-lighting, the gas knob cannot be
turned from pilot to off unless the knob it depressed
slightly.
1. STOP! Read the safety information on the operating
label.
2. Turn off all electric power to the fi replace.
3. Turn the gas knob clockwise
4. Wait 5 minutes to clear out any gas. If you smell gas,
including near the fl oor, STOP! Follow "B" on the op-
erating label. If you don't smell gas, go to the next
step.
5. If the fi replace is equipped with a fl ame adjustment
valve, turn clockwise to off.
6. Find pilot located in front of the back log on the right.
7. Turn gas knob clockwise
8. This unit is equipped with an auto-spark.
Depress and hold gas knob . Keep knob fully
depressed for one minute, then release. If pilot does
not continue to burn repeat steps 3 through 7.
9. With pilot lit, push and turn gas knob counter-clock
wise to on.
10. If equipped with fl ame adjustment valve, turn knob to
high.
11. If equipped with remote on-off switch, main burner
may not come on when you turn the valve to on or
high. Remote switch must be in the
on position to ignite burner.
12. Turn on all electric power to
the fi replace.
W415-0614_05.15.07
to off.
to pilot.
FIGURE 50

OPERATING INSTRUCTIONS

When lit for the fi rst time, the fi replace will emit a slight
odour for a few hours. This is a normal temporary condi-
tion caused by the curing of the logs and the "burn-in" of
internal paints and lubricants used in the manufacturing
process and will not occur again. Simply open a window to
suffi ciently ventilate the room.
After extended periods of non-operation such as following
a vacation or a warm weather season, the fi replace may
emit a slight odour for a few hours. This is caused by dust
particles in the heat exchanger burning off. Open a window
to suffi ciently ventilate the room.
Purge all gas lines with the glass door of the fireplace
removed. Assure that a continuous gas flow is at the
burner before installing the door.
WHAT TO DO IF YOU SMELL GAS
• Do not touch any electric switch.
• Do not use any phone in your building.
• If you cannot reach your gas supplier, call the fi re
department.
• Turn off all gas to the fi replace.
• Do not try to light any appliance.
• Immediately call your gas supplier from a
neighbor's phone. Follow the gas
supplier's instructions.
FIGURE 51
TO TURN OFF GAS
1. Turn off all electric power to the fi replace if service is to
be performed.
2. For a complete shut-down procedure: push in gas
control knob slightly and turn clockwise
Do not force.
3. For a temporary shut-down procedure: set the switch
to off. Press and turn the gas knob clockwise
to pilot.
GAS KNOB
to off.