Comtech EF Data KST-2000L Installation And Operation Manual page 73

Satellite Terminal System
Terminal Mode Commands
Reference Command
Current Faults Response
ADAP Command
2 and 4 Watt Response
SSPAs
Current Faults
LNB Command
Current Faults Response
AGC Command
Current Faults Response
Common Command
Equipment Response
Current Faults
Clear Command
Stored Faults Response
Up Converter Command
Stored Faults Response
Down Converter Command
Stored Faults Response
Reference Stored Command
Faults Response
<add/RS_'cr'
>add/RS_'cr'
REF_yyy'cr'
72MHZ_xxx'cr'
OSC_zzz'cr'
SFLT_#'cr''lf']
<add/HS_'cr'
>add/HS_'cr'
RF_yyy'cr'
HPA_xxx'cr'
BV1_xxx'cr'
+9.75V_xxx'cr'
-5V_xxx'cr'
PROG_xxx'cr'
SFLT_#'cr''lf']
<add/LS_'cr'
>add/LS_'cr'
LNA_xxx'cr'
SFLT_#'cr''lf']
<add/AGS_'cr'
>add/AGS_'cr'
EIP_xxx'cr'
IIP_xxx'cr'
LOOP_xxx'cr'
SFLT_#'cr''lf']
<add/CES_'cr'
>add/CES_'cr'
M&C_xxx'cr'
-7V_xxx'cr'
+7V_xxx'cr'
+12V_xxx'cr'
+17V_xxx'cr'
SFLT_#'cr''lf']
<add/CLSF_'cr'
>add/CLSF_'cr''lf']
<add/USF_#'cr'
>add/USF_#'cr'
RF_yyy'cr'
UC_xxx'cr'
SSYN_xxx'cr'
KSYN_xxx'cr'
LSSYN_xxx'cr'
LKSYN_xxx'cr'
PROG_xxx'cr''lf']
<add/DSF_#'cr' Where xxx = OK or FLT, #= stored fault loaction (0 to 9), DC =
>add/DSF_#'cr' downconverter,
DC_xxx'cr' LSYN = Ku-Band synthesizer lock detect, KSYN = Ku-band
LSYN_xxx'cr' synthesizer lock detect, LLSYN = latched Ku-Band synthesizer
KSYN_xxx'cr' lock detect, LKSYN = latched Ku-band synthesizer lock detect,
LLSYN_xxx'cr' inter processor communications
LKSYN_xxx'cr'
PROG_xxx'cr''lf']
<add/RSF_#'cr' Where yyy = INT, xxx = OK or FLT, zzz = WARM or COLD, # =
>add/RSF_#'cr' stored fault location, 72MHZ = 72 MHz lock detect, LOCK and
REF_yyy'cr' PHASE_N and RANGE refer to an external reference
72MHZ_xxx'cr'
OSC_zzz'cr''lf']
7–9
Where yyy = INT, xxx = OK or FLT, zzz = WARM or COLD, # =
number of stored faults, 72MHZ = 72 MHz lock detect, LOCK and
PHASE_N and RANGE refer to an external reference
Where yyy = ON or OFF, xxx = OK or FLT, BV1 = bias voltage
#1, PROG = inter processor communications, # = number of stored
faults (1 to 10)
Where xxx = OK or FLT, # = number of stored faults (1 to 10)
Where xxx = OK or FLT, # = number of stored faults (1 to 10),
EIP = excessive input power, IIP = insufficient input power,
LOOP = loop converge
Where xxx = OK or FLT, # = number of stored faults (1 to 10)
Clears all stored faults in all locations
Where # = stored fault location (0 to 9), yyy = ON or OFF, xxx =
OK or FLT, ( 1 to 10), RF = RF output, UC = upconverter,
SSYN = S-band synthesizer lock detect, KSYN = Ku-band
synthesizer lock detect, LSSYN = latched S-band synthesizer lock
detect, LKSYN = latched Ku-band synthesizer lock detect, inter
processor communications
Revision 2
MN/KST2000L.IOM