Safety Information; Specifications - Panasonic CQ-RX400U Installation Instructions Manual

Operating Instructions
Panasonic
Safety Information
This pictograph intends to alert you to the presence
of important operating instructions and installation
instructions, Failure to heed the instructions may result in
injury or material damage,
it
Caution
This manual uses pictographs to show you how to use the product
safely and to alert you to potential dangers resulting from improper
connections and operations, The meanings of the pictographs
are explained below. It is important that you fully understand the
meanings of the pictographs in order to use this manual and the
system properly.
This pictograph intends to alert you to the presence
of important operating instructions and installation
instructions. Failure to heed the instructions may result
in severe injury or death.
A
Read the operating instructions for the unit and all other
components of your car audio system carefully before using the
system. They contain instructions about how to use the system in
a safe and effective manner. Panasonic assumes no responsibility
for any problems resulting from failure to observe the instructions
given in this manual.
Warning
I
AAC WMA MP3 CD Player/Receiver
Model:
CQ-RX400U
WMA MP3 CD Player/Receiver
Model:
CQ-RX200U/CQ-RX100UI
CQ-RX100L
(Ca-RX400U)
- Please read these instructions (including "Limited Warranty" and "Customer Services Directory") carefully before using this product
and keep this manual for future reference.
Customer Care Plan
Product Registration Card
Observe the following warnings when Installing.
ClDisconnectthe lead from the negative
H
ballery
terminal belore Installation.
Wiring and installation with the negative (-) battery terminal
connected may cause electrical shock and injury due to a short
circuit. Some cars equipped with the electrical safety system have
specific procedures of battery terminal disconnection.
FAILURE TO FOLLOW THE PROCEDURE MAY LEAD TO THE
UNINTENDED ACTIVATION OF THE ELECTRICAL SAFETY SYSTEM
RESULTING IN DAMAGE TO THE VEHICLE AND PERSONAL
INJURY OR DEATH.
ClNever use salefy-related components lor Installation,
grounding, and other such functions.
Do not use safety-related vehicle components (fuel tank, brake,
suspension, steering wheel, pedats, airbag, etc.) for wiring or
fixing the product or its accessories,
Clinstalllng the product on fhe air bag cover or in a location
where it Interferes with alrbag operation Is prohibited.
ClCheck lor piping, gasoline tank, electric wiring, and
other Items belore Installing the product.
If you need to open a hole in the vehicle chassis to attach or wire
the product, first check where the wire harness, gasoline tank,
and electric wiring are located. Then open the hole from outside if
possible,
ClNever Install the product In a location where
It
Interferes
with your field of vision.
ClNever have the power cord branched to supply other
equipment with power.
ClAtter Installation and wiring, you should check the
normal operation 01 other electrical equipment.
The continuation of their using in abnormal conditions may cause
fire, electrical shock or a traffic accident.
Clln the case of installation to an airbag-equipping
car, confirm warnings and caullons 01 the vehicle
manulacturer before Installation.
ClMake sure the leads do not interfere with driving or
gelling in and out 01 the vehicle.
Cllnsulate all exposed wires to prevent shorl circuiting.
A
Warning
Observe the following warnings when using this
unit.
ClThe driver should neither watch the display nor operate
the system while driving.
Watching the display or operating the system will distract the
driver from looking ahead of the vehicle and can cause accidents,
Always stop the vehicle in a safe location and use the parking
brake before watching the display or operating the system.
ClUse the proper power supply.
This product is designed for operation with a negative grounded
12 V DC battery system. Never operate this product with other
banery systems, especially a 24 V DC battery system,
ClKeep ballerles and insulation film out ot reach ot intants.
Batteries and insulation film can be Ingested, so keep them out of
the reach of infants, If an infant ingests a battery or insulation film,
please seek immediate medical attention.
ClProtectthe Deck Mechanism.
Do not insert any foreign objects into the slot of this unit.
ClDo not disassemble or modify the unit.
Do not disassemble, modify the unit or attempt to repair the
product yourself, If the product needs to be repaired, consult your
dealer or an authorized Panasonic Servicenter,
ClDo not use the unit when It Is out of order.
If the unit is out of order (no power, no sound) or in an abnormal
state (has foreign objects in it, is exposed to water. is smoking, or
smells), turn it off immediately and consult your dealer.
ClThe remote control unit should not lie about in the car.
If the remote controf unit lies about, it could fall on the floor while
driving, get wedged under the brake pedal, and lead to a traffic
accident.
ClRefer fuse replacement to qualllied service personnel.
When the fuse blows out, eliminate the cause and have it replaced
with the fuse prescribed for this unit by a qualified service
engineer. Incorrect replacement of the fuse may lead to smoke,
fire, and damage to the product.
MP3 WMA AAC
(CO-RX400U)
Notes:
- The number in parentheses underneath each accessory part
name is the part number for maintenance and service,
- Accessories and their part numbers are subject to modification
without prior notice due to improvements.
- Mounting Collar and Trim Plate are mounted on the main unit at
shipment.
a'ty
Mounting Collar 1
(YEFX0217263A)
~
Trim Plate 1
(YGFC051023)
" Power Connector 1
:--1
(Kl HY12YYOO03j
~ Remote Control Unit (includes a
1
battery)
(EUR7641010)
&
'ij.§;t:§l.lelil
'3'1;1
IIml' 1
Removable Face Plate Case
(YGFA134302)
Installation kit (YEPOFZ5698) a'ty
Lock Cancel Plate
"-
/ /
Mounting Bolt (5 mm <p)
1 set
'/
U
Rubber Bushing
1 set
a'ty
a'ty
1 set
lilloO§@
DIGITAL AUDIO
I
TEXT
I
Operating Instructions
(English: YGFM286048)
(Fran~ais: YGFM286049)
.(Espaiiol:..... YGFM286050) ...
'B'I;£Ia
llll ,1
'5·§j':fN·lil
System Upgrade Guidebook
. (Y~FM26?850)
Installation Instructions
(YGFM294416)
l
-
Operating Instructions
(English: YGFM286048)
........ .... (.Es.paii.~.I .•..... !.~.Fr,,?~6.0?O) ....
Installation Instructions
(YGFM294416)
l
D
Instruction kit ''''';E"en!'
Accessories
Instruction kit
'3'0;£I"JIlII ' 4 ' 0 ;££411.111 'a'liE1ult!••
«'''liff'III,111 .,ItI;t:lnlUll
Request for use 01 the Removable Face Plate Case:
- To avoid trouble and ensure safety, use the optional Removable
Face Plate Case (YGFA134302).
Panasonic Sales Company,
Division of Panasonic Puerto
Rico, Inc. ("PSC")
Ave, 65 de Infanteria, Km. 9,5
San Gabriel Industrial Park,
Carolina, Puerto Rico 00985
http://www.panasonic.com
General
© 2007 Matsushita Electric Industnal Co. Ltd. All Right Reserved.
Perchlorate Matenal - speCial handling may apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate.
~
Caution
uOo not install the product where it is exposed to strong
vibrations or is unstable.
Observe the following cautions when using this
Avoid slanted or strongly curved surfaces for installation, If the
unit.
installation is not stable. the unit may fall down while driving and
UKeep the sound volume at an appropriate level.
this can lead to an accident or injury,
Keep the volume level low enough to be aware 01 road and traffic
:.Jlnstallation Angle
conditions while driVing.
The product should be installed in a horizontal position with the
front end up at a convenient angle, but not more than 3D',
UThis unit is designed lor use exclusively in automobiles.
The user should bear in mind that in some areas there may be
UDo not operate the unit for a prolonged period with the restrictions on how and where this unit must be Installed. Consult
engine turned olt.
your dealer for turther details.
Operating the audio system for a long period of time with the
.JWear gloves lor salety. Make sure that wiring is
engine turned off will drain the battery,
completed belore installation.
'::IDo not expose the unit to direct sunlight or excessive UTo prevent damage to the unit, do not connect the power
heat.
connector until the whole wiring is completed.
Otherwise these will raise the interior temperature of the unit, and .JDo not connect more than one speaker to one set 01
it may lead to smoke. fire. or other damage to the unit.
speaker leads, (except lor connecting to a tweeter)
uDo not use the product where it is exposed to water,
Observe the following cautions when handling the
moisture, or dust.
Exposure of the unit to water, moisture, or dust may lead to
battery for the remote control unit.
smoke, fire, or other damage to the unit. Make especially sure that
- Use only specified battery (CR2025).
the unit does not get wet in car washes or on rainy days,
- Match the polarity of the battery with the (+) and
H
marks in the
:::ISet the volume level to low enough before the AUX
battery case.
connection is completed.
- Replace a dead battery as soon as possible.
Failure to observe this, the loud noise may come out and damage
- Remove the battery from the remote control unit when not using it
your speakers and your hearing, Direct connection of the speaker/
for an extended period of time.
headphone output of an external device without any attenuator
-Insulate the battery (by placing them in a plastic bag or covering
may distort sound or damage the connected external device.
them with vinyl tape) before disposal or storage.
- Dispose of the battery according to the local regulations,
Observe the following cautions when installing, - Do not disassemble, recharge, heat or short the battery. Do not
I.JRefer wiring and installation to qualified service personnel.
throw a battery into a fire or water.
Installation of this unit requires special skills and experience. For In case of ballery leakage
maximum safety, have it installed by your dealer. Panasonic is not liable - Thoroughly wipe the battery liquid off the battery case and insert
for any problems resulting from your own installation of the unit. new battery,
::JFollow the instructions to install and wire the product.
- If any part of your body or clothing comes into contact with battery
Not following the instructions to properly install and wire the
liquid, wash it with plenty of water.
product could cause an accident or fire,
-If battery liquid comes into contact with your eyes, wash them with
wTake care not to damage the leads.
plenty of water and get immediate medical attention.
When wiring, fake care not to damage the leads, Prevent them
Observe the following cautions when using
USB
from getting caught in the vehicle chassis, screws, and moving
parts such as seat rails, Do not scratCh, pull, bend or twist the
device.
14.'iQumil
leads, Do not run them near heat sources or place heavy objects
- Do not connect a USB device directly to this unit. If the USB device
on them, If leads must be run over sharp metal edges, protect the
is connected directly to this unit and an accident occurs, or if the
leads by winding them with vinyl tape or similar protection.
brakes are applied suddenly, the driver or passenger may bump
OUse the designated parts and tools for installation.
into the USB device and may get injured
Use the supplied or designated parts and appropriate tools to
- Position the USB device and USB extension cable so that they do
install the product. The use of parts other than those supplied
not obstruct your driving,
or designated may result in internal damage to the unit. FaUlty
- Do not connect any USB device other than USB memory, a USB
installation may lead to an accident, a malfunction or fire,
audio player or iPod series. Do not connect multiple USB devices
UOo not block the air vent or the cooling plate 01 the unit.
to the USB connector. Drawing power for multiple USB devices
Blocking these parts will cause the interior of the unit to overheat
from the connector could cause overheating and smoking.
and will result in fire or other damage.
~
Caution
The loll owing applies only in the U_S.A.
Parf15 of the FCC Rules
THIS PRODUCT IS A CLASS I LASER PRODUCT.
FCC Warning:
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF
Any unauthorized changes or modifications to this equipment would
PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY
void the user's authority to operate this device,
RESULT IN HAZARDOUS RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT REPAIR BY YOURSELF.
Notice
REFER SERVICING TO OUALIFIED PERSONNEL.
This product contains a CR COin Cell lithium Battery which contains
:530kHz-1710kHz
27 dB/~V (22 ~V, SIN 20 dB)
87.9 MHz -107.9 MHz
:10.2 dB! (0.9 ~V, 75 0)
:15.2 dB! (1.6 ~V, 75 0)
30 Hz -15 kHz (±3 dB)
:75 dB
:35 dB (at 1 kHz)
55 dB
100 dB
62 dB
Panasonic Canada Inc.
5770 Ambler Drive,
Mississauga, Ontario
L4W 2T3
http://www.panasonic.ca
YGFM286048A FT1007-1117 Printed in China
FM
Radio
Frequency range
Usable sensitivity
AM
Radio
Frequency range
Usable sensitivity
50 dB quieting sensitivity
Frequency response
Alternate channel selectivity
Stereo separation
Image rejection ratio
IF rejection ratio
Signal/noise ratio
Notes:
- Specifications and design are subject to modification without
notice due to improvements,
- Some figures and illustrations in this manual may be different
from your product.
Power Output:
18 W RMS x4 Channels at 40 and
s
1 % THD+N
Signal to Noise Ratio:
85 dBA (reference: 1 W into 4 0)
Above specifications comply with EIA standards.
:8 times oversampling
'1 bit DAC System
.Astigma 3-beam
:Semiconductor laser
790 nm
20 Hz - 20 kHz (±1 dB)
:96 dB
0,01 % (1 kHz)
:Below measurable limits
85 dB
:10 kO
:20
V
:3.5 mm <p Stereo mini-pin
:178 x 50 x 160 mm
17" xl 15/16" x 6 5/16"1
:1.2 kg 121bs, 10 ozl
:DC 12 V (11 V- 16 V DC), test
voltage 14.4 V. negative ground
:Less than 2.1 A
(CD mode: 0.5 W x 4 channels)
:50 W x 4 channels (at 1 kHz),
volume control maximum
SO Low/Bass: ±12 dB
(at 60 Hz, 80 Hz, 100 Hz, 200 Hz)
So
Mid: ±12 dB
(at 500 Hz, 1 kHz, 2 kHz, 3 kHz)
So
HighlTreble: ±12 dB
(at 10kHz, 12 kHz, 15 kHz, 18 kHz)
:4 - 8 0
:2.0 V (CD mode, 1 kHz. 0 dB)
:2000
Specifications
Tone/SO adjustment range
Disc Player
Panasonic Consumer
Electronics Company,
Division of Panasonlc
Corporation of North America
One Panasonic Way, Secaucus,
New Jersey 07094
http://wwwpanasonic.com
Current consumption
Maximum power output
Power supply
Sampling frequency
DA converter
Pick-up type
Light source
Wave length
Frequency response
Signal to noise ratio
Total harmonic distortion
Wow and flutter
Channel separation
Speaker impedance
Pre-amp output voltage
Pre-amp output impedance
USB Connector '3'1;£((.IIIII
USB Standard Compatibility '1.1/2.0 Full Speed
Maximum Supply Current :500 mA
Front AUX Input
Input impedance
Allowable external input
Connector
Dimensions (W x H x D)
Weight