Mount The Camera - Panasonic BL-C1 Getting Started

Security Warning window on Microsoft Windows XP Service Pack 2
To view a video (Motion JPEG), ActiveX Controls must be installed. Follow the steps shown below to install ActiveX Controls.
Click the warning displayed above the tabs, and click [Install
ActiveX Control...].
4.

Mount the camera.

The camera can be mounted in the following ways.
Note
• Do not mount the camera where the sun light directly hits the camera or in
outdoor-type housing without a temperature control system. The camera
may malfunction due to high temperature.
• When you mount the camera, always hook the AC adaptor cord to the
hook.
Hook for
AC adaptor cord
Stand Mount
Note
Disconnect all cables from the camera. Reconnect the cables after mounting the
camera.
Stand/Tripod
Mounting Hole
Mounting
Screw
Ceiling Mount
Note
• Do not mount the camera upside down, since the image will be displayed
upside down.
• We recommend only mounting the camera using the provided hardware.
Mounting in any other manner may cause the camera to fall, resulting in
personal injury or damage to the camera.
• To reduce the load on the mounting hardware, dress the cables neatly and
secure with tape.
• Disconnect all cables from the camera. Reconnect the cables after mounting
the camera.
Mount the flexible stand firmly to the
ceiling with the two screws (included).
Screws
Allow sufficient space
between the wall and the
flexible stand to turn the
Position Lock.
• Do not mount the camera on a soft
material. The camera may fall and
be damaged.
• Use appropriate screws for the
material of the ceiling.
Adjust the angle, then fasten
the Position Lock.
Position Lock
Loosen the Position Lock
located on the rear side of
the flexible stand.
Turn the Mounting Screw to
attach the camera.
Adjust the angle, then fasten
the Position Lock.
Position
Lock
Flexible
Stand
Loosen the Position Lock located
on the rear side of the flexible stand,
and turn the Mounting Screw to
attach the camera.
Position Lock
Stand/Tripod
Mounting Hole
Connect the AC adaptor cord and
the Ethernet cable to the camera.
Dress the cables neatly and secure
with tape (customer-provided).
Tape
(customer-provided)
Click [Install].
• This product is for indoor use only. Do not use it outdoors.
• The camera may become warm. This is not a malfunction.
Mount the camera where the AC adaptor can reach a power outlet, or use an
•
extension cord (customer-provided).
• Do not mount the camera upside down, since the image will be displayed upside
down.
Top
Bottom
Tripod Mount
Note
• Do not use a tripod screw
with a thread of 6 mm or
more. This may damage the
Stand/Tripod mounting hole.
• The camera cannot be
mounted depending on the
shape of the camera
platform.
Wall Mount
Note
• Do not mount the camera upside down, since the image will be displayed
upside down.
• We recommend only mounting the camera using the provided hardware.
Mounting in any other manner may cause the camera to fall, resulting in
personal injury or damage to the camera.
• To reduce the load on the mounting hardware, dress the cables neatly and
secure with tape.
• Disconnect all cables from the camera. Reconnect the cables after mounting
the camera.
Mount the flexible stand firmly to the
wall with the two screws (included).
Allow sufficient space between the
ceiling and the flexible stand to turn
the Position Lock.
Screws
• Do not mount the camera on a soft
Mounting Screw
material. The camera may fall and
be damaged.
• Use appropriate screws for the
material of the wall.
Adjust the angle, then fasten
the Position Lock.
Position Lock
Make sure the indicator is
always in the upper right
corner.
Stand/Tripod
Mounting Hole
Tripod
(customer-
provided)
Loosen the Position Lock located
on the rear side of the flexible stand,
and turn the Mounting Screw to
attach the camera.
Indicator
Connect the AC adaptor cord and
the Ethernet cable to the camera.
Dress the cables neatly and secure
with tape (customer-provided).
Tape
(customer-provided)
Stand/Tripod
Mounting
Hole
Position
Lock
Mounting
Screw