Making A New Folder; Initializing A Memory Card; Advanced Features - JVC GR-D90 Instructions Manual

5
Select the number of prints by rotating the MENU/
%
VOLUME wheel
Repeat steps 3 through 5 for the desired number of
prints.
• The number of prints can be set up to 15.
• To correct the number of prints, select the image
again and change the number.
6
Rotate the MENU/VOLUME wheel
"RETURN" and press it. Selection is complete. "SAVE?"
appears.
• If you did not change any settings in step 3 through 5,
the Menu Screen reappears.
7
Rotate the MENU/VOLUME wheel
"EXECUTE", then press it to save the setting you have
just made.
• To cancel selection, rotate the MENU/VOLUME wheel
%
to select "CANCEL" and press it.
To Reset The No. Of Prints . . .
..... select "RESET" in step 4 of "TO PRINT ALL STILL
IMAGES (ONE PRINT FOR EACH)" on pg. 21.
The number of prints is reset to 0 for all still
images.
While performing the above, never disconnect power,
as this may cause the memory to be corrupted. For
safety, all buttons including the Power Switch
disabled in step 6.
NOTES:
"BATTERY LOW" appears if the battery remaining power
is too low.
If you load a memory card already set as shown above in
a printer compatible with DPOF, it will make prints of the
selected still images automatically.
To print images recorded on a tape, first dub them to a
memory card ( pg. 21).

Making A New Folder

New still pictures you are going to take can be
separated from previously shot pictures by resetting the
file name to DVC00001; these new pictures will be
stored in a new folder.
1
Set the VIDEO/DSC Switch
y
the Power Switch
t
Lock Button located on the switch.
• A stored file is displayed.
2
Press the MENU/VOLUME wheel
Screen appears. Rotate the MENU/VOLUME wheel
to select "NO. RESET", then press it. The NO. RESET
Screen appears.
3
Rotate the MENU/VOLUME wheel
"EXECUTE", then press it. The new folder (such as
"101JVCGR") will be made and the file name of the
next shot starts from DVC00001.
EN

ADVANCED FEATURES

22
(GR-D90 and GR-D70 only)
and press it.
%
to select
%
to select
CAUTION
4
to "DSC", then set
to "PLAY" while pressing down the
%
in. The Menu
%
to select
Folder and File names
Each time shooting takes place, a file name is made
using a number which is larger by one than the
largest number of the file names which are in use.
Even if you delete an image file with a number in
the middle of range, the number will not be used for
a new shot; a gap will remain in the numerical
sequence. If the file name reaches DVC09999, a
new folder (such as "101JVCGR") will be made and
the file name will start again from DVC00001.
You can initialize a memory card anytime.
After initializing, all files and data stored on the
memory card, including those which have been
protected, are cleared.
1
Perform step 1 of "Making A New Folder".
2
Press the MENU/VOLUME wheel
Screen appears. Rotate the MENU/VOLUME wheel
to select "FORMAT" and press it. The FORMAT Screen
appears.
3
Rotate the MENU/VOLUME wheel
"EXECUTE" and press it. The memory card is
y
are
initialized. When initialization is finished, "NO IMAGES
STORED" appears.
• To cancel initialization, rotate the MENU/VOLUME
%
wheel
Do not perform any other operation (such as turning off
the camcorder) during initialization. Also, be sure to use
the provided AC Adapter, as the memory card may be
corrupted if the battery becomes exhausted during
initialization. If the memory card becomes corrupted
initialize it.
%

Initializing A Memory Card

to select "RETURN" and press it.
CAUTION
%
in. The Menu
%
%
to select