The Video Settings - TANDBERG Codec C90 Administrator's Manual

TANDBERG Codec C90 and Profiles using C90
Contents Contents Introduction Introduction

The Video settings

Video DefaultPresentationSource
Define which video input source shall be used as the default presentation source (e.g. when you press the
Presentation key on the remote control). The input source is configured to a video input connector. See
the Video Input Matrix table at the back of the codec and the description of the Video Input Matrix in the
Interfaces section.
Value space: <1..5>
Range: Select the video source to be used as the presentation source.
Example: Video DefaultPresentationSource: 3
Video Input DVI [3, 5] Type
The official DVI standard supports both digital and analog signals. In most cases the default AutoDetect
setting can detect whether the signal is analog RGB or digital. However, in some rare cases when DVI-I
cables are used (these cables can carry both the analog and digital signals) the auto detection fails. This
setting makes it possible to override the AutoDetect and select the correct DVI video input. This setting
should also be used if the video input is an analog component (YPbPr) type signal. This is used by some
cameras (Sony EVI-HD1) and DVD/Blu-ray players. Since it is not possible to auto detect the difference
between AnalogRGB and AnalogYPbPr, the AnalogYPbPr setting must be selected.
Value space: <AutoDetect/Digital/AnalogRGB/AnalogYPbPr>
AutoDetect: Set to AutoDetect to automatically detect if the signal is analog RGB or digital.
Digital: Set to Digital to force the DVI video input to Digital when using DVI-I cables with both analog
and digital pins and AutoDetect fails.
AnalogRGB: Set to AnalogRGB to force the DVI video input to AnalogRGB when using DVI-I cables
with both analog and digital pins and AutoDetect fails.
AnalogYPbPr: Set to AnalogYPbPr to force the DVI video input to AnalogYPbPr, as the component
(YPbPr) signal cannot be auto detected.
Example: Video Input DVI 3 Type: AutoDetect
Video Input Source [1] Connector
Select which video input connector to be active on video input source 1.
Value space: <HDMI/HDSDI/YPbPr>
HDMI: Select HDMI when you want to use the HDMI 1 as input source 1.
HDSDI: Select HD-SDI when you want to use the HD-SDI 1 as input source 1.
YPbPr: Select YPbPr when you want to use the YPbPr 1 (Component) connectors as input source 1.
Connect to the first row of Y, Pb and Pr connectors.
Example: Video Input Source 1 Connector: HDMI
D14635.03—MAY 2010
Advanced config.
Advanced configuration Advanced configuration Password protection Password protection About monitors About monitors Audio matters Audio matters
The Video settings,
cont...
Video Input Source [2] Connector
Select which video input connector to be active on video input source 2.
Value space: <HDMI/HDSDI/YPbPr>
HDMI: Select HDMI when you want to use the HDMI 2 as input source 2.
HDSDI: Select HD-SDI when you want to use the HD-SDI 2 as input source 2.
YPbPr: Select YPbPr when you want to use the YPbPr 2 (Component) as input source 2. Connect to
the second row of Y, Pb and Pr connectors.
Example: Video Input Source 2 Connector: HDMI
Video Input Source [3] Connector
Select which video input connector to be active on video input source 3.
Value space: <HDMI/HDSDI/DVI>
DVI: Select DVI-I when you want to use the DVI-I 3 as input source 3.
HDMI: Select HDMI when you want to use the HDMI 3 as input source 3.
HDSDI: Select HD-SDI when you want to use the HD-SDI 3 as input source 3.
Example: Video Input Source 3 Connector: DVI
Video Input Source [4] Connector
Select which video input connector to be active on video input source 4.
Value space: <HDMI/HDSDI>
HDMI: Select HDMI when you want to use the HDMI 4 as input source 4.
HDSDI: Select HD-SDI when you want to use the HD-SDI 4 as input source 4.
Example: Video Input Source 4 Connector: HDMI
Video Input Source [5] Connector
Select which video input connector to be active on video input source 5.
Value space: <DVI/Composite/YC>
DVI: Select DVI-I when you want to use the DVI-I 5 as input source 5.
Composite: Select Composite when you want to use Composite as input source 5.
YC: Select YC when you want to use the S-Video (YC) as input source 5. Connect to the two
connectors marked Y/Comp and C.
Example: Video Input Source 5 Connector: DVI
31
Administrator guide
Appendices Appendices Contact us Contact us
www.tandberg.com