Replacing Gateway Notebook Components • Identifying the notebook model • Identifying components • Preparing your work space • Preventing static electricity discharge • Preparing the notebook...
Replacing Gateway Notebook Components www.gateway.com Use this service guide to help plan maintenance tasks for the following Gateway Important This service guide is not intended to be notebooks: provided to individual users or consumers. It cannot be provided to M460 ■...
Identifying components Identifying components Use this chart to identify the main components of the notebook. For a complete list of replaceable parts, see “Contents” on page LCD panel assembly (see page Keyboard cover (see page Keyboard (see page Cooling assembly...
Replacing Gateway Notebook Components www.gateway.com Preparing your work space Before performing maintenance on the notebook, make sure that your work space and the notebook are correctly prepared. Wear a grounding (ESD) wrist strap, and use a grounded or dissipative ■...
■ Tape Some of the procedures in this guide involve removing tape that holds cables or components. Two types of tape are used in this Gateway notebook: Mylar, non-conductive tape is typically transparent, with a red or brown ■ tint.
Replacing Gateway Notebook Components www.gateway.com Disconnecting from the port replicator To separate the notebook from the port replicator: Press down on the docking release latch. The notebook will spring up slightly. Lift the notebook off of the port replicator. Removing the batteries...
Page 11
Preparing the notebook Slide the battery release latch, then slide the battery out of the notebook. Removing the optional secondary battery To remove the optional secondary battery: Remove the security screw if your notebook has one. Security screw Slide the bay module release latch. The secondary battery moves out slightly.
Replacing Gateway Notebook Components www.gateway.com Adding or replacing memory modules Tools you need to complete this task: Important Use only memory modules designed for this Gateway notebook. Phillips #0 screwdriver Screws removed during this task: 1 black (keyboard) Memory bay...
Page 13
Adding or replacing memory modules To add or replace memory modules: Complete the steps in “Preparing the notebook” on page Remove the keyboard screw. Tips & Tricks The screw hole is marked with a K. Screw Loosen the six memory bay cover screws (these screws cannot be removed).
Page 14
Replacing Gateway Notebook Components www.gateway.com If you are removing a module, gently press outward on the clip at each end of the memory module until the module tilts upward. Pull the memory module out of the slot.
Page 15
Adding or replacing memory modules Hold the new or replacement module at a 30-degree angle and press it into the empty memory slot. This module is keyed so it can only be inserted in one direction. If the module does not fit, make sure that the notch in the module lines up with the tab in the memory bay.
Replacing Gateway Notebook Components www.gateway.com Replacing the cooling assembly Tools you need to complete this task: Phillips #0 screwdriver Additional materials you need to complete this task: X-23-7762 thermal grease ■ Screws removed during this task: 1 black (keyboard) To replace the cooling assembly: Complete the steps in “Preparing the notebook”...
Page 17
Replacing the cooling assembly Loosen the six memory bay cover screws (these screws cannot be removed), then remove the memory bay cover. Screws Use the thumb notch to lift the memory bay cover, then remove it. Be careful not to break off the tabs located on the end of the cover opposite of the thumb notch.
Page 18
Replacing Gateway Notebook Components www.gateway.com At the same time as you lift, move the cooling assembly away from the Caution The cooling assembly cable is attached to side of the notebook. the system board at this point. Be careful not to break the cable.
Replacing the processor Replacing the processor Tools you need to complete this task: Phillips #0 screwdriver Additional materials you need to complete this task: X-23-7762 thermal grease ■ Screws removed during this task: 1 black (keyboard) To replace the processor: Complete the steps in “Preparing the notebook”...
Page 20
Replacing Gateway Notebook Components www.gateway.com Use a flat-blade screwdriver to turn the processor lock screw 1/4-turn counter-clockwise. Screw...
Page 21
Replacing the processor Remove the old processor from the system board. Install the new processor onto the system board making sure that Pin 1 on the processor (indicated by the silk-screened arrow on the corner of the processor) aligns with Pin 1 on the processor socket (indicated by the absence of a pin hole in the processor socket), then use a flat-blade screwdriver to turn the processor lock screw 1/4-turn clockwise.
Replacing the IEEE 802.11 wireless card Tools you need to complete this task: Caution By law, only approved wireless modules provided by Gateway or a Gateway authorized representative, explicitly for this Gateway notebook, may be installed Phillips #0 screwdriver in this notebook.
Page 23
Replacing the IEEE 802.11 wireless card To replace the 802.11 wireless card: Complete the steps in “Preparing the notebook” on page Loosen the wireless bay cover screw (this screw cannot be removed), then remove the wireless bay cover. Unplug the two antenna cables.
Page 24
Replacing Gateway Notebook Components www.gateway.com If the wireless card is held by clips, press outward on the clip at each side of the card until the card tilts upward. -OR- If the wireless card is held by a screw, remove the screw.
Page 25
Replacing the IEEE 802.11 wireless card Pull the old card out of the slot. Hold the new card at a 30-degree angle and slide it into the empty slot. This card is keyed so it can only be inserted in one direction. If the card does not fit, make sure that the notch in the card lines up with the tab in the card slot.
Page 26
Replacing Gateway Notebook Components www.gateway.com Reattach the light gray antenna cable to the connector labelled MAIN or M, then reattach the black antenna cable to the connector labelled AUX or A. Replace the wireless bay cover, then tighten the screw.
Replacing the hard drive kit Replacing the hard drive kit Tools you need to complete this task: Phillips #0 screwdriver Screws removed during this task: 2 black (hard drive kit) 4 chrome (hard drive cover) Hard drive kit To replace the hard drive kit: Complete the steps in “Preparing the notebook”...
Page 28
Replacing Gateway Notebook Components www.gateway.com Slide the old hard drive bay kit, then remove it. Remove the four screws that secure the hard drive to the hard drive cover. Screws Screws...
Page 29
Replacing the hard drive kit Remove the cover from the old drive. Place the new drive, label side up, onto the cover so the screw holes line Replace the screws that secure the cover to the drive. Slide the new hard drive kit into your notebook, then replace the kit...
Replacing Gateway Notebook Components www.gateway.com Replacing the keyboard cover Tools you need to complete this task: Flat-blade driver - OR - Scribe or non-marring tool Phillips #0 screwdriver Screws removed during this task: 2 black (keyboard cover) To replace the keyboard cover: Complete the steps in “Preparing the notebook”...
Page 31
Replacing the keyboard cover Insert the small flat-blade screwdriver or non-marring tool under the right Tips & Tricks Inserting a piece of cloth between the end of the keyboard cover and gently pry it up. screwdriver and keyboard will help prevent damage to the notebook.
Replacing Gateway Notebook Components www.gateway.com Replacing the keyboard Tools you need to complete this task: Flat-blade driver - OR - Scribe or non-marring tool Phillips #0 screwdriver Screws removed during this task: 2 black (keyboard cover) 1-3 black (keyboard) To replace the keyboard: Complete the steps in “Preparing the notebook”...
Page 33
Replacing the keyboard Loosen the six memory bay cover screws (these screws cannot be removed). Screws Use the thumb notch to lift the memory bay cover, then remove it. Be careful not to break off the tabs located on the end of the cover opposite of the thumb notch.
Page 34
Replacing Gateway Notebook Components www.gateway.com Remove the two optional keyboard screws. Important Depending on the keyboard features, one or both of these screws may be absent. Screw Screw Turn your notebook over so the top is facing up, then open the LCD panel to the fully opened position.
Page 35
Replacing the keyboard Lift the black keyboard connector clip and optional EZ Point clip, then remove the cables. Be careful not to touch or damage any other components. Lift the old keyboard away from the notebook. Place the new keyboard keys-down on your notebook with the space bar away from you.
Page 36
Replacing Gateway Notebook Components www.gateway.com Gently press the keyboard down until it is flat all the way across. The keyboard should easily fall into place. Be careful not to damage the LCD panel. Reinstall the keyboard cover by following the instructions in “Replacing...
Replacing the CMOS battery Replacing the CMOS battery Tools you need to complete this task: Flat-blade driver - OR - Scribe or non-marring tool Phillips #0 screwdriver Screws removed during this task: 2 black (keyboard cover) 1-3 black (keyboard)
Page 38
Replacing Gateway Notebook Components www.gateway.com Use your fingers to unplug the CMOS battery connector from the system board. Be careful not to touch or damage any other components. Plug the new battery into the system board. Important Use only CMOS batteries designed for your Gateway notebook.
Replacing the LCD panel assembly Replacing the LCD panel assembly Tools you need to complete this task: Flat-blade driver - OR - Scribe or non-marring tool Phillips #0 screwdriver Screws removed during this task: 2 black (keyboard cover) 4 chrome (LCD panel hinges)
Page 40
Lift up on the video cable retaining clips slightly, then slide the video cable from under the clips. Taking care to note the cable routing and positions as they are installed from Gateway, pull the antenna wires out from under the system board, then slide the wires from under the retaining clips.
Page 41
Replacing the LCD panel assembly Remove the four hinge screws that secure the LCD panel to the notebook. Screws Lift the LCD panel assembly away from the notebook. The LCD panel assembly is now completely detached from the notebook.
Page 42
Replacing Gateway Notebook Components www.gateway.com Slide the antenna cables through the retaining clips, under the system board, and into the wireless card area. Slide the LCD video cable under the retaining clips, then plug the LCD video connector into the notebook.
Replacing the LCD panel inverter Replacing the LCD panel inverter Tools you need to complete this task: Flat-blade driver - OR - Scribe or non-marring tool Phillips #0 screwdriver Screws removed during this task: 2 chrome (bracket) 6 chrome (LCD panel assembly)
Page 44
Replacing Gateway Notebook Components www.gateway.com Remove the six screws from the front of the LCD panel assembly. Screws Screws Carefully separate the front and back of the LCD panel assembly.
Page 45
Replacing the LCD panel inverter Remove the two screws holding the bracket to the LCD panel assembly, then remove the bracket. Screw Screw Unplug both cables from the inverter. Remove the old inverter, then insert the new one. Connect the cables to the new inverter.
Replacing Gateway Notebook Components www.gateway.com Replacing the LCD panel or LCD panel assembly lid Tools you need to complete this task: Flat-blade driver - OR - Scribe or non-marring tool Phillips #0 screwdriver Screws removed during this task: 2 black (keyboard cover)
Page 47
Replacing the LCD panel or LCD panel assembly lid Remove the six rubber inserts from the front of the LCD panel assembly. Rubber inserts Rubber inserts Remove the six screws from the front of the LCD panel assembly. Screws...
Page 48
Replacing Gateway Notebook Components www.gateway.com Carefully separate the front and back of the LCD panel assembly. Remove the two screws holding the bracket to the LCD panel assembly, then remove the bracket. Screw Screw...
Page 49
Replacing the LCD panel or LCD panel assembly lid Remove the six screws connecting the LCD panel to the LCD panel assembly. Screw Screw Screw Screw Screw Screw Remove the LCD panel from the LCD panel assembly lid.
Page 50
Replacing Gateway Notebook Components www.gateway.com If you are replacing the LCD panel into an existing lid and you need to transfer the existing LCD panel inverter to the new panel, unplug both cables from the inverter, then plug them into the new LCD panel.
Page 51
Replacing the LCD panel or LCD panel assembly lid Replace the six LCD panel assembly screws. Replace the six rubber inserts. Reassemble the notebook.
Replacing Gateway Notebook Components www.gateway.com Replacing the palm rest Tools you need to complete this task: Flat-blade driver - OR - Scribe or non-marring tool Phillips #0 screwdriver Screws removed during this task: 2 black (keyboard cover) 2 black (hard drive kit)
Page 53
Replacing the palm rest Remove the keyboard by following the instructions in “Replacing the keyboard” on page Remove the LCD panel by following the instructions in “Replacing the LCD panel assembly” on page Lift the black touchpad connector clip, then remove the cable. Be careful not to touch or damage any other components.
Page 54
Replacing Gateway Notebook Components www.gateway.com Turn the notebook over so the bottom is facing up. Remove the 17 screws shown in the following picture. Note the location of the six short screws. Screws Screws Lift the palm rest assembly completely from the notebook.
Replacing the modem Replacing the modem Tools you need to complete this task: Flat-blade driver - OR - Scribe or non-marring tool Phillips #0 screwdriver Screws removed during this task: 2 black (keyboard cover) 2 black (hard drive kit)
Page 56
Replacing Gateway Notebook Components www.gateway.com Remove the keyboard by following the instructions in “Replacing the keyboard” on page Remove the LCD panel by following the instructions in “Replacing the LCD panel assembly” on page Remove the palm rest by following the instructions in “Replacing the palm...
Page 57
Replacing the modem Unplug the modem cable from the old modem and plug it into the new modem. Install the new modem onto the system board. Replace the modem screws removed in Step Reassemble the notebook.
Replacing Gateway Notebook Components www.gateway.com Replacing the TPM module Tools you need to complete this task: Flat-blade driver - OR - Scribe or non-marring tool Phillips #0 screwdriver Screws removed during this task: 2 black (keyboard cover) 2 black (hard drive kit)
Page 59
Replacing the TPM module Remove the keyboard by following the instructions in “Replacing the keyboard” on page Remove the LCD panel by following the instructions in “Replacing the LCD panel assembly” on page Remove the palm rest by following the instructions in “Replacing the palm...
Replacing Gateway Notebook Components www.gateway.com Replacing the Bluetooth module Tools you need to complete this task: Flat-blade driver - OR - Scribe or non-marring tool Phillips #0 screwdriver Screws removed during this task: 2 black (keyboard cover) 2 black (hard drive kit)
Page 61
Replacing the Bluetooth module Remove the keyboard by following the instructions in “Replacing the keyboard” on page Remove the LCD panel by following the instructions in “Replacing the LCD panel assembly” on page Remove the palm rest by following the instructions in “Replacing the palm...
Replacing Gateway Notebook Components www.gateway.com Replacing the system board Tools you need to complete this task: Flat-blade driver - OR - Scribe or non-marring tool Phillips #0 screwdriver Additional materials you need to complete this task: X-23-7762 thermal grease ■...
Page 63
Replacing the system board To replace the system board: Complete the steps in “Preparing the notebook” on page If your notebook has a module in the modular bay, remove it by following the instructions in “Removing the optional secondary battery” on page Remove the memory by following the instructions in “Adding or replacing...
Page 64
Replacing Gateway Notebook Components www.gateway.com Disconnect the speakers and the Bluetooth card. Bluetooth connector Speaker connector Remove the four screws that secure the system board to the notebook. Screws...
Page 65
Replacing the system board Turn the system board over and disconnect the external video board from the old system board and connect it to the new system board. Install the new system board into your notebook, replacing the screws you...
Replacing Gateway Notebook Components www.gateway.com Replacing the external video board Tools you need to complete this task: Flat-blade driver - OR - Scribe or non-marring tool Phillips #0 screwdriver 5.0 mm hex nutdriver Additional materials you need to complete this task: X-23-7762 thermal grease ■...
Page 67
Replacing the external video board To replace the external video board: Complete the steps in “Preparing the notebook” on page If your notebook has a module in the modular bay, remove it by following the instructions in “Removing the optional secondary battery” on page Remove the cooling assembly by following the instructions in “Replacing...