Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Omron MicroAIR U22
Summary of Contents for Omron MicroAIR U22
- Page 1 Instruction manual IM-NE-U22-E-08-01/2014 1665580-0F...
- Page 2 How to select the nebulization mode ....13 How to inhale with the OMRON MicroAIR U22 ... . 14 How to clean the unit after each inhalation .
- Page 3 This product is intended to be used for inhaling medication for respiratory disorders. Intended User healthcare personnel or patient under the guidance of qualified medical MicroAIR U22 and the content of instruction manual. Intended Patients This product should not be used by patients, who are unconscious or are not breathing spontaneously.
- Page 4 The manufacturer cannot be held liable for any damage caused by improper or incorrect use. infirmities or children). problems, stop using the nebulizer and contact your OMRON dealer. directive, operating the device should be avoided in direct vicinity of other electronic devices.
- Page 5 In the MicroAIR U22, aerosol is generated by pushing liquid medication through fine holes in the newly developed metal alloy mesh. This is realised by a titanium vibrator, oscillating at high frequency. This unique technology offers the following features and benefits: The device will fit in any handbag or briefcase.
- Page 6 The following items are contained in the package: Medication Mesh Cap Main Unit Cover Main Unit Container (with Mesh) Mask Adapter Mouthpiece Soft Pouch Child Mask (PVC) Adult Mask (PVC) Batteries...
- Page 7 Contains metal alloy mesh for Mesh cap viewed from nebulization. the bottom Figure viewed from the above Protects the mesh. Efficient nebulization is realized through the use of minute pores. Do not touch this fragile part with your fingers! Do not attempt to clean with a cotton swab or a pin! Stabilizes nebulization.
- Page 8 Medication container can be removed when the buttons on both sides are pushed. Connects the main unit with the vibrator. An orange light blinks when the batteries are low. Connects the vibrator with the main unit. A green light turns on when the power is on. Battery Cover Battery cover removal lever...
- Page 9 1. Remove the battery cover by slightly rotating the disengaging lever in the direction of the arrow (1). 2. Insert the batteries according to the battery polarity indicated inside the battery compartment. 3. Replace battery cover by aligning tabs and, with your thumbs, push into place until it clicks.
- Page 10 When using the unit for the first time or after not using it for a long period of time, clean and disinfect the medication container, mesh, mask adapter, mouthpiece and mask. Refer to page 15 for instructions. 1. Insert batteries, see page 9. 2.
- Page 11 4. Fill the medication container as illustrated. 5. Install the mesh cap. The mesh cap seals the medication bottle. Confirm if the cap is securely installed. 6. Install the medication container on the main unit.
- Page 12 7. Install the mask adapter on the main unit. 8. Install the mask or mouthpiece on the mask adapter. The device is now ready for use.
- Page 13 If you push the ON/OFF ( / I) button and release within mode. If you push the / I button again, the unit stops nebulization. The green power indicator lights up during nebulization. If you hold the ON/OFF ( 2 seconds or more, the unit nebulizes in the manual nebulization mode.
- Page 14 Caution: Only use type and amount of medications as prescribed and instructed by your doctor. Medication 1. Slightly tilt the unit as illustrated in the figure. In this position, the vibrator is immersed in the medication and nebulization will start after power on. After the vibrator has been immersed in the medication, the unit can be used under any angle.
- Page 15 Note: if the device is not cleaned and disinfected correctly and frequently, micro-organisms may remain in the unit, causing risk of infection. The following items should be cleaned Medication container, mesh cap, mask adapter, mouthpiece and mask. 1. Remove the mask adapter from the main unit. 2.
- Page 16 5. Wash the parts (not the main unit!) in a warm soapy solution. Rinse the parts in warm tap water to remove the soap residue. Some types of medications can easily remain on the mesh, therefore pay close attention during washing. Do not touch the mesh with a cotton swab, or with a pin.
- Page 17 Note: if the device is not cleaned and disinfected correctly and as frequently as indicated, microorganisms may remain in the unit, causing risk of infection. Before disinfection, always first clean the parts as described in the section “How to clean the unit after each inhalation”...
- Page 18 Use the table below as a guideline to select a method for disinfecting. ammonium Mouthpiece SEBS Mask Adapter Body : PSF Horn :Titanium Medication ± ± Hinges :Titanium Container Packing : Silicone Cap: PSF Packing : Silicone ± Mesh Cap Mesh Holder : PC Mesh : NiPd Mask : PVC...
- Page 19 The mesh cap is a consumable part. Remove the mesh cap and install a new one as described on page 10 (section “How to assemble the unit and fill the medication container”). In case the performance of the unit remains reduced even after cleaning and disinfecting, use the following methods to remove dried medication, lime or saliva which may clog the tiny holes in the mesh cap.
- Page 20 Batteries are low (the orange Replace the batteries with new ones. Refer to page 9. The nebulization rate is The mesh is stained or clogged. 1. Clean the mesh by boiling. Refer to page 15. 2. Replace the mesh cap with a new one.
- Page 21 Refer to page 15. indicator turns on but the unit does not nebulize. on the mesh Refer to page 17. If the unit does not nebulize properly after checking the possible causes above, contact your OMRON dealer.
- Page 22 MicroAIR U22 (NE-U22-E) Electronic Mesh Nebulizer 3 VDC (two alkaline penlite batteries/Type AA/LR6) 2.4 VDC (two NiMH rechargeable batteries) 10°C ~ 40°C, 30% ~ 85% RH -20°C ~ 60°C, 10% ~ 95% RH, 700 ~ 1060 hPa Main Unit, Main Unit Cover, Medication Container, Mesh Cap, Mask Adapter, Mouthpiece, 2 Batteries (AA/LR6), Child Mask (PVC), Adult Mask (PVC), Soft Pouch, Instruction Manual, Warranty Card Japan.
- Page 23 URL: www.omron-healthcare.com * Independently measured at SolAero Ltd., Canada, Dr. John Dennis, according to EN13544-1:2007. ** The Nebulization rate is measured with saline 0.9% solution at 23°C and can vary with medication and ambient conditions.
- Page 24 EN60601-1-2 standard has been implemented. This standard defines emissions for medical devices. This medical device manufactured by OMRON HEALTHCARE conforms to this EN60601-1-2:2007 standard for both immunity and emissions. Nevertheless, special precautions need to be observed: electromagnetic fields, near the medical device.
- Page 25 Correct Disposal of This Product (Waste Electrical & Electronic Equipment) This marking shown on the product or its literature, indicates that it should not be disposed of, with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.
- Page 26 (within the scope of EC Medical Device Directive 93/42/EEC) Adult Mask (PVC) NEB-MSLP-E Child Mask (PVC) NEB-MSMP-E Mesh Cap 9518216-4 Medication Container 1140678-0 Mask Adapter 4997115-4 Mouthpiece 9520281-5...
- Page 28 617-0002 JAPAN Scorpius 33, 2132 LR Hoofddorp, THE NETHERLANDS www.omron-healthcare.com Matsusaka Factory Mie, 515-8503 Japan www.omron-healthcare.co.uk Gottlieb-Daimler-Strasse 10, 68165 Mannheim, GERMANY www.omron-healthcare.de www.omron-healthcare.fr Made in Japan...