Page 1
Product Manual Seagate Ultra Mobile HDD ® Zero Gravity Sensor models ST500LT035 ST320LT033 Gen 9.3 100737403 Rev. C May 2014...
Page 2
Publication number: 100737403, Rev. C May 2014 Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries. Seagate Ultra Mobile HDD and SeaTools are either trademarks or registered trademarks of Seagate Technology LLC or one of its affiliated companies in the United States and/or other countries.
Authorized Service Centers For information regarding Warranty Support, visit: http://www.seagate.com/support/warranty-and-replacements/ For information regarding data recovery services, visit: http://www.seagate.com/services-software/data-recovery-services/ For Seagate OEM and Distribution partner portal, visit: http://www.seagate.com/partners/ For Seagate reseller portal, visit: http://www.seagate.com/partners/my-spp-dashboard/ Seagate Ultra Mobile HDD Product Manual, Rev. C...
NTRODUCTION ® This manual describes the functional, mechanical and interface specifications for the following Seagate Ultra Mobile HDD model drives: Zero Gravity Sensor models ST500LT035 - 1E9G42 ST320LT033 - 1E9G4C These drives provide the following key features: 5400-RPM spindle speed.
The specification summaries listed in the following tables are for quick reference. For details on specification measurement or definition, refer to the appropriate section of this manual. Drive Specification ST500LT035 ST320LT033 Formatted capacity 500 GB...
RIVE PECIFICATIONS Drive Specification ST500LT035 ST320LT033 5–200 Hz: 2.0 Gs Vibration, operating 201–500 Hz: 1.0 Gs Vibration, nonoperating 5–500 Hz: 5.0 Gs Nonrecoverable read errors 1 per 10 bits read To determine the warranty for a specific drive, use a web browser to access the following web page: http://www.seagate.com/support/warranty-and-replacements/...
RIVE PECIFICATIONS ECORDING AND NTERFACE ECHNOLOGY Interface Serial ATA (SATA) Recording method Perpendicular Recording density 1885 Kb/in Track density 366 ktracks/in avg Areal density 690 Gb/in Spindle speed 5400 RPM +/- 0.2% Sustained data transfer rate 100 MB/s max I/O data-transfer rate 600 MB/s max HYSICAL HARACTERISTICS...
RIVE PECIFICATIONS OWER PECIFICATIONS The drive receives DC power (+5V) through a native SATA power connector (refer to Figure 2.7.1 Power consumption Power requirements for the drives are listed in the table below. Typical power measurements are based on an average of drives tested, under nominal conditions, at 25°C ambient temperature.
Page 11
RIVE PECIFICATIONS 2.7.1.1 Typical current profiles The typical 5V startup and operation current profile is shown in Figure Figure 1 Typical 5V Startup and Operation Current Profile HDD P EAGATE LTRA OBILE RODUCT ANUAL...
RIVE PECIFICATIONS 2.7.2 Conducted noise Input noise ripple is measured at the host system power supply across an equivalent 15-ohm resistive load on the +5 volt line. Using 5-volt power, the drive is expected to operate with a maximum of 100 mV peak-to-peak square-wave injected noise at up to 10 MHz.
NVIRONMENTAL PECIFICATIONS This section provides the temperature, humidity, shock, and vibration specifications for Seagate Ultra Mobile HDD drives. Ambient temperature is defined as the temperature of the environment immediately surrounding the drive. Above 1000 feet (305 meters), the maximum temperature is derated linearly by 1°C every 1000 feet.
Seagate follows the ECMA-74 standards for measurement and identification of PDTs. An exception to this process is the use of the absolute threshold of hearing. Seagate uses the lower limit for the threshold curve* to discern tone audibility and to compensate for the inaudible components of sound prior to computation of tone ratios according to Annex D of the ECMA-74 standards.
Communications Commission verification or certification of the device is required. Seagate has tested this device in enclosures as described above to ensure that the total assembly (enclosure, disk drive, motherboard, power supply, etc.) does comply with the limits for a Class B computing device, pursuant to Subpart J, Part 15 of the FCC rules. Operation with noncertified assemblies is likely to result in interference to radio and television reception.
Users should use caution exposing any electronic components to uncontrolled chemical pollutants and corrosive chemicals as electronic drive component reliability can be affected by the installation environment. The silver, copper, nickel and gold films used in Seagate products are especially sensitive to the presence of sulfide, chloride, and nitrate contaminants. Sulfur is found to be the most damaging. In addition, electronic components should never be exposed to condensing water on the surface of the printed circuit board assembly (PCBA) or exposed to an ambient relative humidity greater than 95%.
Figure Figure 2 Attaching SATA Cabling Signal connector Power connector Signal cable Power cable Each cable is keyed to ensure correct orientation. Seagate Ultra Mobile HDD drives support latching SATA connectors. HDD P EAGATE LTRA OBILE RODUCT ANUAL...
ONFIGURING AND OUNTING THE RIVE RIVE OUNTING Mount the drive in any orientation using four screws in the side-mounting holes. Refer to for drive mounting dimensions. Follow Figure 3 these important mounting precautions when mounting the drive: Allow a minimum clearance of 0.030 in (0.76 mm) around the entire perimeter of the drive for cooling. ...
For detailed information about the Serial ATA interface, refer to the Serial ATA: High Speed Serialized AT Attachment specification. OMPATIBILITY Seagate Ultra Mobile HDD drives incorporate connectors which enable hot plugging of these drives in accordance with the Serial ATA: High Speed Serialized AT Attachment specification revision 2.0. This specification can be downloaded from www.serialata.org. This device requires a COMRESET from the host after a hotplug event.
ATA (SATA) I ERIAL NTERFACE OTES All pins are in a single row, with a 1.27 mm (0.050 in) pitch. The comments on the mating sequence apply to the case of backplane blindmate connector only. In this case, the mating sequences are: •...
Page 21
Table 6 Supported ATA commands ATA-standard commands names Command code (in hex) Set Features Set Max Address Note: Individual Set Max commands are identified by the Address: value placed in the Set Max Features register as defined to Password: the right. Lock: Unlock: Freeze Lock:...
Firmware revision: x.xx (8 ASCII character string, padded with blanks to end of string) 27–46 Drive model number: ST500LT035 (40 ASCII characters, padded with blanks to end of string) ST320LT033 (Bits 7–0) 8010 Maximum sectors per interrupt on Read multiple and Write multiple (16)
Page 23
Read Multiple or Write Multiple command 60–61 Total number of user-addressable sectors ST500LT035 = 0FFFFFFFh This field contains a value that is one greater than the total number of ST320LT033 = 0FFFFFFFh user-addressable sectors. The maximum value that shall be placed in this field is 0FFFFFFFh.
Page 24
98-99 Streaming Performance Granularity 0000 100–103 Total number of user-addressable LBA sectors available ST500LT035 = 976,773,168 (see Section 3.2 for related information) ST320LT033 = 625,142,448 These words are required for drives that support the 48-bit addressing feature. Maximum value: 0000FFFFFFFFFFFFh.
Page 25
ATA (SATA) I ERIAL NTERFACE Word 88 Ultra DMA mode 0 is supported. Ultra DMA mode 1 is supported. Ultra DMA mode 2 is supported. Ultra DMA mode 3 is supported. Ultra DMA mode 4 is supported. Ultra DMA mode 5 is supported. Ultra DMA mode 6 is supported.
ATA (SATA) I ERIAL NTERFACE 4.3.2 Set Features command This command controls the implementation of various features that the drive supports. When the drive receives this command, it sets BSY, checks the contents of the Features register, clears BSY and generates an interrupt. If the value in the register does not represent a feature that the drive supports, the command is aborted.
) that eliminates unnecessary drive returns. The diagnostic software ships with all new drives and is also available at: http://www.seagate.com/support/downloads/seatools/. This drive is shipped with S.M.A.R.T. features disabled. A recent BIOS or software package that supports S.M.A.R.T. is needed to enable this feature.
Page 30
NDEX UL60950-1 11 vibration 9 voltage dips, interrupts 10 voltage tolerance 8 warranty 11 weight 5 width 5 Write Buffer 17 Write DMA 17 Write DMA Extended 17 Write Long with Retries 17 Write Long without Retries 17 Write Multiple 17 Write Sectors 17 HDD P EAGATE...
Page 31
Seagate Technology LLC 10200 South De Anza Boulevard, Cupertino, California 95014, United States, 408-658-1000 ASIA/PACIFIC Seagate Singapore International Headquarters Pte. Ltd. 7000 Ang Mo Kio Avenue 5, Singapore 569877, 65-6485-3888 EUROPE, MIDDLE EAST AND AFRICA Seagate Technology SAS 16-18 rue du Dôme, 92100 Boulogne-Billancourt, France, 33 1-4186 10 00 Publication Number: 100737403, Rev.