Related Manuals for Seagate ST5000LM000
Summary of Contents for Seagate ST5000LM000
- Page 1 SATA 2.5" Product Manual Standard models ST5000LM000 ST4000LM024 ST3000LM024 100804767, Rev. E February 2017...
- Page 2 Seagate, Seagate Technology, BarraCuda and the Spiral logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries. MTC Technology and SeaTools are either trademarks or registered trademarks of Seagate Technology LLC or one of its affiliated companies in the United States and/or other countries. The FIPS logo is a certifi- cation mark of NIST, which does not imply product endorsement by NIST, the U.S., or Canadian governments.
-
Page 3: Table Of Contents
4.3.3 S.M.A.R.T. commands......................28 Seagate BarraCuda Product Manual, Rev. E (Draft 2) - Page 4 Mounting Dimensions (for 1-disk models) ............18 Seagate BarraCuda Product Manual, Rev. E (Draft 2)
-
Page 5: Seagate® Technology Support Services
For information regarding online support and services, visit: http://www.seagate.com/contacts/ For information regarding Warranty Support, visit: http://www.seagate.com/support/warranty-and-replacements/ For information regarding data recovery services, visit: http://www.seagate.com/services-software/seagate-recovery-services/recover/ For Seagate OEM, Distribution partner and reseller portals, visit: http://www.seagate.com/partners/ Seagate BarraCuda Product Manual, Rev. E (Draft 2) -
Page 6: Introduction
Introduction This manual describes the functional, mechanical and interface specifications for the following: Seagate® BarraCuda® model drives: Standard models ST5000LM000 ST4000LM024 ST3000LM024 These drives provide the following key features: 128MB buffer. • 5400-RPM spindle speed. • 650 Gs non-operating shock and 300 Gs of operating shock. -
Page 7: Specifications
1.2A Voltage tolerance (including noise) 5V ± 5% Operating temperature 0° to 60°C Non-operating temperature (Ambient) –40° to 70°C 20°C per hour max (operating) Temperature gradient (max) 35°C per hour max (non-operating) Seagate BarraCuda Product Manual, Rev. E (Draft 2) -
Page 8: Formatted Capacity
512 (logical) / 4096 (physical) 3TB models 3000 GB 5,860,533,168 One GB equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment and formatting. Seagate BarraCuda Product Manual, Rev. E (Draft 2) -
Page 9: Lba Mode
69.85 +/- 0.25 mm (2.750 +/- 0.010 in) Width 100.35 +0.20 / -0.25 mm (3.951 +0.008 / -0.010 in) All models Length 190 g (0.42lb) Weight (max) Cache buffer 128 MB (129,536 KB) Seagate BarraCuda Product Manual, Rev. E (Draft 2) -
Page 10: Seek Time
DC input voltages and nominal operating temperature. Start/stop times Table 3: Start/stop times Capacity 5TB, 4TB and 3TB models Typical seek times (ms) Typical Power-on to ready (sec) Standby to ready (sec) Seagate BarraCuda Product Manual, Rev. E (Draft 2) -
Page 11: Power Specifications
Equivalent resistance is calculated by dividing the nominal voltage by the typical RMS read/write current. Note 2.8.3 Supply Voltage Allowable voltage 5V ± 5% Allowable noise/ripple 100 mV p-p max, 0-30 MHz Allowable supply rise time 1-100 ms Allowable supply fall time <5 s Seagate BarraCuda Product Manual, Rev. E (Draft 2) -
Page 12: Power-Management Modes
The drive leaves Sleep mode after it receives a Hard Reset or Soft Reset from the host. After receiving a reset, the drive exits Sleep mode and enters Standby mode. Seagate BarraCuda Product Manual, Rev. E (Draft 2) -
Page 13: Environmental Specifications
Environmental Specifications This section provides the temperature, humidity, shock, and vibration specifications for Seagate BarraCuda drives. Ambient temperature is defined as the temperature of the environment immediately surrounding the drive. Above 1000 feet (305 meters), the maximum temperature is derated linearly by 1°C every 1000 feet. -
Page 14: Acoustics
Test for prominent discrete tones (PDTs) Seagate follows the ECMA-74 standards for measurement and identification of PDTs. An exception to this process is the use of the absolute threshold of hearing. Seagate uses the lower limit for the threshold curve* to discern tone audibility and to compensate for the inaudible components of sound prior to computation of tone ratios according to Annex D of the ECMA-74 standards. -
Page 15: Reliability
EN 55032, Class B and the immunity levels are defined by EN 55024. Drives are tested in representative end-user systems. Although CE-marked Seagate drives comply with the directives when used in the test systems, we cannot guarantee that all systems will comply with the directives. The drive is designed for operation inside a properly designed enclosure, with properly shielded I/O cable (if necessary) and terminators on all unused I/O ports. -
Page 16: Fcc Verification
Commission verification or certification of the device is required. Seagate has tested this device in enclosures as described above to ensure that the total assembly (enclosure, disk drive, motherboard, power supply, etc.) does comply with the limits for a Class B computing device, pursuant to Subpart J, Part 15 of the FCC rules. Operation with noncertified assemblies is likely to result in interference to radio and television reception. -
Page 17: China Requirements - China Rohs 2
Users should use caution exposing any electronic components to uncontrolled chemical pollutants and corrosive chemicals as electronic drive component reliability can be affected by the installation environment. The silver, copper, nickel and gold films used in Seagate products are especially sensitive to the presence of sulfide, chloride, and nitrate contaminants. Sulfur is found to be the most damaging. In addition, electronic components should never be exposed to condensing water on the surface of the printed circuit board assembly (PCBA) or exposed to an ambient relative humidity greater than 95%. -
Page 18: Unpacking, Configuring And Mounting The Drive
For installations which require cables, users can connect the drive as shown in1. Figure 1 Attaching SATA Cabling Signal connector Power connector Signal cable Power cable Each cable is keyed to ensure correct orientation. BarraCuda drives support latching SATA connectors. Seagate BarraCuda Product Manual, Rev. E (Draft 2) -
Page 19: Drive Mounting
Operating: no performance degradation, emitted noise, 10 mm probe: 2.0kgf (typical) mechanical damage, or hard errors Non-operating: no hard errors 10 mm probe: maximum 2.0kgf (instantaneous) Figure 2 Mounting Dimensions (for 1-disk models) Seagate BarraCuda Product Manual, Rev. E (Draft 2) -
Page 20: Serial Ata (Sata) Interface
Power 5V power 5V power Ground 2nd mate Ground or LED signal If grounded, drive does not use deferred spin Ground 1st mate 12V power, pre-charge, 2nd mate 12V power 12V power Seagate BarraCuda Product Manual, Rev. E (Draft 2) -
Page 21: Supported Ata Commands
Read Long with Retries Read Long without Retries Read Multiple Read Multiple Extended Read Native Max Address Read Native Max Address Extended Read Sectors Read Sectors Extended Read Sectors without Retries Read Verify Sectors Seagate BarraCuda Product Manual, Rev. E (Draft 2) - Page 22 Trusted Receive (SED only) Trusted Receive DMA (SED only) Trusted Send (SED only) Trusted Send DMA (SED only) Write Buffer Write DMA Write DMA Extended Write DMA without Retries Write Long with Retries Seagate BarraCuda Product Manual, Rev. E (Draft 2)
- Page 23 ATA-standard power-management commands Check Power Mode Idle Idle Immediate Sleep Standby Standby Immediate ATA-standard security commands Security Set Password Security Unlock Security Erase Prepare Security Erase Unit Security Freeze Lock Security Disable Password Seagate BarraCuda Product Manual, Rev. E (Draft 2)
-
Page 24: Identify Device Command
Number of current logical heads xxxx Number of current logical sectors per logical track xxxx 57–58 Current capacity in sectors xxxx Number of sectors transferred during a Read Multiple or Write Multiple command xxxx Seagate BarraCuda Product Manual, Rev. E (Draft 2) - Page 25 Enhanced security erase time xxxx Current APM values 8080 Master password revision code FFFE Hardware reset value (see description following this table) xxxx Auto acoustic management setting xxxx Stream Min. Request Size 0000 Seagate BarraCuda Product Manual, Rev. E (Draft 2)
- Page 26 0000 Transport major version number 101F 223–254 ATA-reserved 0000 Integrity word xxA5 See the bit descriptions below for words 63, 88 and 93 of the Identify Drive data. (on next page) Note Seagate BarraCuda Product Manual, Rev. E (Draft 2)
- Page 27 Ultra DMA mode 5 is currently active. Ultra DMA mode 6 is currently active. Word 93 1 = 80-conductor cable detected, CBLID above VIH 0 = 40-conductor cable detected, CBLID below VIL Seagate BarraCuda Product Manual, Rev. E (Draft 2)
-
Page 28: Set Features Command
Disable the Free Fall Protection feature (41 above enables the Free Fall Protection feature) Report full capacity available At power-on, or after a hardware or software reset, the default values of the features are as indicated above Note Seagate BarraCuda Product Manual, Rev. E (Draft 2) -
Page 29: Commands
) that eliminates unnecessary drive returns. The diagnostic software ships with all new drives and is also available at: http://www.seagate.com/support/downloads/seatools/. This drive is shipped with S.M.A.R.T. features disabled. Users must have a recent BIOS or software package that supports S.M.A.R.T. to enable this feature. - Page 30 ASIA/PACIFIC Seagate Singapore International Headquarters Pte. Ltd. 7000 Ang Mo Kio Avenue 5, Singapore 569877, 65-6485-3888 EUROPE, MIDDLE EAST AND AFRICA Seagate Technology SAS 16-18 rue du Dôme, 92100 Boulogne-Billancourt, France, 33 1-4186 10 00 Publication Number: 100804767, Rev. E...