Onkyo Integra TX-DS898 Instruction Manual page 20

Connections
S Video input
Video input
L (white)
Analog audio
input
R (red)
6. VCR (VIDEO 1)
R (red)
Analog audio
output
L (white)
Video output
S Video output
With the initial settings of the TX-DS898, the DVD input source
is set for digital input at the COAXIAL 1 jack.
If the digital connection is made at a different jack, this must be
changed at the Setup menu: Input Setup → Digital Setup (see page
36).
5. Connecting a DVD recorder or other digital video
recording device (VIDEO 2)
Using an RCA-type video connection cable, connect the video
output terminal (composite) on the device to the VIDEO 2 IN jacks
on the TX-DS898 and video input terminal to the VIDEO 2 OUT
jacks. If there is an S video input/output terminal on the device,
connect it to the S VIDEO 2 IN/OUT jack using an S video cable.
You do not need to connect to both the S VIDEO 2 IN and VIDEO 2
IN terminals. If the device has component video outputs, connect
them to one of the COMPONENT VIDEO INPUT jacks.
With the initial settings of the TX-DS898, the VIDEO 2 input
source is set for the COMPONENT VIDEO INPUT 2 jack.
If the video connection is made at COMPONENT VIDEO INPUT 1,
this must be changed at the Setup menu: Input Setup → Video Setup
→ Component Video (see page 38).
Using an RCA-type audio connection cable, connect the audio
output terminal on the device to the same VIDEO 2 IN audio jacks
on the TX-DS898 and audio input terminal to the VIDEO 2 OUT
audio jacks. Make sure that you properly connect the left channel to
the L jack and the right channel to the R jack.
If the device has a digital output jack as well, be sure to also connect
it to either a DIGITAL INPUT (COAXIAL) or DIGITAL INPUT
(OPTICAL) jack on the TX-DS898 depending on the type of
connector on the device.
With the initial settings of the TX-DS898, the VIDEO 2 input
source is set for digital input at the COAXIAL 3 jack.
If the digital connection is made at a different jack, this must be changed
at the Setup menu: Input Setup → Digital Setup (see page 36).
20
DIGITAL PRE
AUDIO
OUTPUT
TENNA R
OPT FRONT
1
R L
SUB
AM
2
OUT
COAX SURR
1 IN
SURR
BACK/
ZONE 2
FM
2
OUT
75
FRONT
3 IN
DIO
L
OPT
SUB
1 PH OUT
SURR
2 CD IN
SURR
OUT
BACK
3 IN
R
TAPE
4 IN
GND IN
L R L
DIGITAL DIO AUDIO
INPUT
COMPONENT
VIDEO S VIDEO
VIDEO
OUTPUT
MONITOR
OUT
Y
ZONE 2 P
B
DVD P
R
INPUT 1
Y
VIDEO 1
P
B
P
R
VIDEO 2
INPUT 2
Y
VIDEO 3 P
B
VIDEO 4 P
R
VIDEO S VIDEO
If the device also has a digital input jack, it can be connected to the
DIGITAL OUTPUT (OPTICAL) jack on the TX-DS898 for digital
recording of the source for REC OUT at the TX-DS898.
Note:
The output from the DIGITAL OUTPUT jack of the TX-DS898 is
only the digital signal input to the DIGITAL INPUT jack.
6. Connecting a video cassette recorder (VIDEO 1)
Using an RCA-type video connection cable, connect the video
output terminal (composite) on the video cassette recorder to the
VIDEO 1 IN jacks on the TX-DS898 and video input terminal to the
VIDEO 1 OUT jacks. If there is an S video input/output terminal on
the video cassette recorder, connect it to the S VIDEO 1 IN/OUT
jack using an S video cable. You do not need to connect to both the S
VIDEO 1 IN and VIDEO 1 IN terminals. If the video cassette
recorder has component video outputs, connect them to one of the
COMPONENT VIDEO INPUT jacks.
With the initial settings of the TX-DS898, the VIDEO 1 input
source is set for the COMPONENT VIDEO INPUT 2 jack.
If the video connection is made at COMPONENT VIDEO INPUT 1,
this must be changed at the Setup menu: Input Setup → Video Setup
→ Component Video (see page 38).
Using an RCA-type audio connection cable, connect the audio
output terminal on the video cassette recorder to the same VIDEO 1
IN audio jacks on the TX-DS898 and audio input terminal to the
VIDEO 1 OUT audio jacks. Make sure that you properly connect the
left channel to the L jack and the right channel to the R jack.
With the initial settings of the TX-DS898, the VIDEO 1 input
source is set for digital input at the COAXIAL 2 jack.
If the digital connection is made at a different jack, this must be
changed at the Setup menu: Input Setup → Digital Setup (see page
36).
7. Settop box, video camera
(VIDEO 3)
R (red)
Analog audio
output
L (white)
Video output
S Video output
Digital audio output (optical)