Page 1
SYSTEM AIR CONDITIONER Basic : DH094EAMC AQV24AWAX Model : DH070EAS UH070EAS DH052EAS UH052EAS Model Code : DH070EAS UH070EAS Model Code : DH052EAS UH052EAS AIR CONDITIONER THE FEATURE OF PRODUCT Easier installation : Silm size Built-in duct type High performance & Energy saving DH052/070EAS ...
5-2 Outdoor Unit ............................. 5-3 Ass’y Control Out ..........................16. Electrical Parts List ........................17. Wiring Diagram ..........................7-1 Indoor Unit ............................7-2 Outdoor Unit ............................ 18. Schematic Diagram ........................8-1 Indoor Unit ............................8-2 Outdoor Unit ............................ Samsung Electronics...
Page 3
14-2 Pressure Graph 14-2 ..........................14-3 Pressure & Capacity mark 14-3 ......................14-4 Q & A for Non-trouble 14-4 ........................14-5 Cleaning/Filter Change 14-7 ......................... 14-6 Installation 14-8 ............................14-7 Installation Diagram of Indoor Unit and Outdoor Unit 14-9 ............Samsung Electronics...
Do not place a cloth or other materials over it. Remove the batteries if you don’t use the remote control for a long time. (If applicable) Use the remote control within 7 meters from the indoor unit. (If applicable) Samsung Electronics...
Young children or infirm persons should be always supervised when they use the air conditioner. Max current is measured according to IEC standard for safety. Current is measured according to ISO standard for energy efficiency. Samsung Electronics...
It can give the benefit to the installers and aries the reliability of the air conditioner. Long Ambient Operation (In Low Temperature) It can arise the reliability and the capacity of the air conditioner, especially operated in low temperature. Eco-friendly Product (Lead-Free, RoHS, WEEE) Samsung Electronics...
2-3 The Comparative Specifications of Product Development Model Comparative Model Item DH070(052)EAS DH094EAMC Indoor Unit Design Outdoor Unit Indoor Unit 29.0kg 35.0kg Net Weight Outdoor Unit 50.0kg 74.0kg Indoor Unit 900X260X480(mm) 1,150x260x480(mm) Outer Dimension (WxHxD) Outdoor Unit 880X638X310(mm) 880X798X310(mm) Indoor Unit...
2. Outdoor unit error Communication error between the outdoor unit (Display is unrelated Main-Inverter Micom(After 1 minute of Main-Inverter with operation) detection) Flickering, If you turn off the air conditioner when the LED is flickering, the LED is also turned off. Samsung Electronics...
Setting the outdoor unit capacity option error Detection of the float switch Error of setting option switches for optional accessories EEPROM error EEPROM option error Flickering, If you turn off the air conditioner when the LED is flickering, the LED is also turned off. Samsung Electronics...
Page 12
Outdoor Unit Discharge over temperature Protetion Control Error [Inverter] Compressor starting error Primary Current Over Trip error [Inverter] DC PEAK error(O.C) [Inverter] Compressor Rotation error [Inverter] Current Sensor error [Inverter] DC LINK Sensor error [Inverter] EEPROM Read/Write Error Samsung Electronics...
Page 13
Outdoor unit Capacity Setup option error Communication error between Indoor unit and wired remote control Wired remote control error Communication error between Master and Slave wired remote control COM1/COM2 Cross-installed error Error of setting option for wired remote control COM2 Samsung Electronics...
Operation condition secession (Cooling) DC-Link voltage sensor error I_Trip error GAS Leak error Power Cable miss connection Power ON reset(1sec) Capacity miss match Test Operation at Cooling Mode Test Operation at Heating Mode LED ON, LED OFF, LED BLINK Samsung Electronics...
Push the button to set the display panel to Every time you push the button, the display panel reads . . . repeatedly. Samsung Electronics...
Page 16
If all lamps of indoor unit are flickering, Plug out, plug in power plug again and press ON/OFF key to retry. If the unit is not working properly or all lamps are continuously flickering after setting the option code, see if the correct option code is set up for its model. Samsung Electronics...
Blower & Motor screws, detach Ass'y Cabi Bottom Blower. 2) Detach from Ass'y Control In the capacitor connection wire between the Motor Fan and housing connector. 3) After disassembling 2 places indicating screws, detach the 2 Fan Case. Samsung Electronics...
Page 20
Remark 4) After disassembling 2 places indicating screws, detach Fan Motor and Blower from the set. 1) After disassembling 1 Indicating screw, Control In detach the Cover control. 2) Detach the Motor-Fan and Sensor Connector from the PCB. Samsung Electronics...
Page 21
Parts Procedure Remark 3) Disassemble 4 indicating screws and detach Control In from the set. Drain Pan Work is possible when Disassembling the Ass'y Cabi Bottom Blower. 1) Disassemble 7 indicating screws and detach Ass'y Cabi Bottom Drain. Samsung Electronics...
Page 22
Remark 2) Disassemble 4 indicating screws and detach the Drain Pan. (2 screws each at left and right side) Work is possible when Disassembling the Evap Ass'y Drain Pan. 1) Disassemble 5 indicating screws to detach Cover Pipe. Samsung Electronics...
Page 23
Parts Procedure Remark 2) Disassemble Sensor on the Evap. 3) Disassemble 4 indicating screws which are in the near of Hanger Plate to detach the Evap. (2 screws each at left and right side) It needs 2 peoples. Samsung Electronics...
1) Loosen 1 fixing screw(CCW) of the Cover- Control and detach the Cover Control. 2) Loosen fixing screws(CCW) and detach the Cabinet-Upper. 3) Loosen 1 screw(CCW) fixed to assemble Control Box with Cabinet-Side RH. 4) Loosen 6 fixing screws(CCW) and detach the Cabinet-Side RH. Samsung Electronics...
Page 25
Disassembly and Reassembly Parts Procedure Remark 6) Loosen fixing screws(CCW) of the Cabinet Front. 5) Loosen 2 screws(CCW) fixed on the Guide Condenser. Samsung Electronics...
Page 26
Motor 2) Detach the Fan Propeller. 3) Loosen 4 fixing screws(CCW) to detach the Motor. 4) Disconnect the wire between Ass’y Control Out and Motor. 5) Loosen 2 fixing screws(CCW) and detach the Bracket Motor. Samsung Electronics...
Page 27
3) Disassemble the pipes in both inlet and outlet with welding torck. Before you disassemble the pipes and Condenser, be sure that there should be no refrigerant remained in the unit. 1) Loosen fixing screw(CCW) and detach the Heat Exchanger 4-10 Samsung Electronics...
Page 28
Procedure Remark Compressor 1) Disassemble the Felt Comp Sound. 2) Loosen the fixing nut(CCW) and detach the Compressor Lead Wire. 3) Loosen the 3 bolts(CCW) at the bottom of Compressor like the picture on the right side. Samsung Electronics 4-11...
PCB Diagram 10-2 Outdoor PCB EMI PCB Power N COND/OLP Temperature Sensor Power L DIS/OUT Temperature Sensor BLDC FAN EEV Connector AC FAN Comp. Connector Wire Communication 485 Reactor Connector Wire Samsung Electronics 10-2...
11. Operating Instructions 11-1 Name of Each Part 11-1-1 Indoor Unit The figures are shwon in this instruction may differ from yours depending on the model. DH070/052EAS inlet outlet 11-1-2 Outdoor Unit Air Inlet (Rear) Air Outlet Connection Valve 11-1 Samsung Electronics...
Air flow direction Swing button On Timer setting On Timer button Off Timer setting Off Timer button Battery discharge indicator On/Off & Timer Set/ Cancel button Note : • After cleaning the air filter, press the button. Samsung Electronics 11-2...
You must not press it. • After cleaning the air filter, press the button. Then the wired remote controller will display the Filter Sign indicator when the time to clean the air filter. 11-3 Samsung Electronics...
3. To adjust the temperature, press the buttons one or more times until the required temperature is displayed. Possible temperatures are between 18˚C and 30˚C inclusive. Samsung Electronics 11-4...
Page 69
Possible temperatures are between 16˚C and 30˚C inclusive. 4. Select the fan speed by pressing the button one or more times until the intended value is displayed : Automatic(rotated : ) Medium High 11-5 Samsung Electronics...
Page 70
2. To select the FAN mode, press the button until is displayed at the top of the wireless remote controller. 3. Select the fan speed by pressing the button one or more times until the intended value is displayed: Medium High Samsung Electronics 11-6...
3. To adjust the temperature, press the buttons one or more times until the required temperature is displayed. Possible temperatures are between 18˚C and 30˚C inclusive. 11-7 Samsung Electronics...
Page 72
Possible temperatures are between 16˚C and 30˚C inclusive. 4. Select the fan speed by pressing the button one or more times until the intended value is displayed : Automatic(rotated : ) Medium High Samsung Electronics 11-8...
Page 73
2. To select the FAN mode, press the button until is displayed at the top of the wired remote controller. 3. Select the fan speed by pressing the button one or more times until the intended value is displayed: Medium High 11-9 Samsung Electronics...
The compressor operates in a reverse cycle to remove Indoor fan and outdoor fan stop operation intermittently exterior ice in a HEAT mode, and indoor fan and outdoor in a HEAT mode. fan do not operate intermittently for within 20% of the total heater operation Samsung Electronics 12-1...
Replace fuse FUSE(F701) : T3.15[A]/250[V] Check the output of SMPS on the control board. Input power: AC230±15%[V] PCB should be replaced IC02 Input: DC12[V] IC02 output: DC5[V] Check the setting temperature 12-2 Samsung Electronics...
Is there no error at the insertion of PCB? Exchange the PCB. Exchange the PCB. Are the BLDC FAN Wire Is the +,- of C102(Outdoor unit) short? 1 and 3 short? Exchange the PCB. Exchange the BLDC FAN. Normal Operation Exit Samsung Electronics 12-3...
Page 77
Pull out the power cord and during the operation?(Square-Wave) execute the following step after 30 seconds. Disassemble the BLDC FAN Wire. Is the short between Exchange the PCB. the BLDC FAN Wires? Exchange the BLDC FAN MOTOR. Exchange the PCB. 12-4 Samsung Electronics...
Page 78
Pull out the power cord and exchange the PCB from the case after 30 seconds. Is the assembly of Micom and Exchange the PCB. peripheral circuit part good? Check again after assembly of PCB. Samsung Electronics 12-5...
Page 79
4-WAY valve coil error of 4-WAY valve coil. Dose the voltage of AC 230V Exchange apply to the connector of 4 WAY the outdoor PCB. valve coil during the operation? Go to the next page 4-WAY valve main body error 12-6 Samsung Electronics...
Page 80
Check the resistance value Outdoor fan error of outdoor fan.(Pin #1~#3) Dose the voltage of DC300V apply to the connector of outdoor Check the motor wire. fan during the operation of outdoor unit? Outdoor PCB error Samsung Electronics 12-7...
Exchange the sensor. (Refer to the R/T TABLE) Is the resistance value of sensor connection pull_up 18K? Exchange the PCB. Exchange the PCB. Normal operation Exit 400.0 350.0 300.0 250.0 200.0 150.0 100.0 50.0 12-8 Samsung Electronics...
Page 82
Exchange the sensor. (Refer to the R/T TABLE) Is the resistance value of sensor connection pull_up 24K? Exchange the PCB. Exchange the PCB. Normal operation Exit 600.0 500.0 400.0 300.0 200.0 100.0 Samsung Electronics 12-9...
Page 83
Exchange the sensor. (Refer to the R/T TABLE) Is the resistance value of sensor connection pull_up 18.2K? Exchange the PCB. Exchange the PCB. Normal operation Exit 400.0 350.0 300.0 250.0 200.0 150.0 100.0 50.0 12-10 Samsung Electronics...
4) Is the resistance value of sensor connection pull_up correct? 2. Troubleshooting procedure Remove the Fan lock. Isn't the Fan locked? Is the connector connected correctly? Connect the connector. Is the color of Fan wire matched correctly? Exchange the Fan. Exchange the PCB. Normal operation Exit Samsung Electronics 12-11...
Page 85
1, 2 correct after power supply? Is the capacitor(C101, C102, C103) Connect the connector. for DC-Link assembled in accordance the specification? Are R113, R114, R115 470kohm? Exchange the PCB. Is R116 14.3kohm? Exchange the Fan. Exchange the PCB. Normal operation Exit 12-12 Samsung Electronics...
Page 86
Is the position of temperature sensor Correct the sensor position or and the sensing value normal? exchange the sensor. Is the connection cable for Correct the cable connection. the compressor and power terminal normal? Exchange the PCB. Samsung Electronics 12-13...
Is the communication error Terminate the service. occurred again? Isn't the power cable and Correct the wrong wiring. communication cable wiring error? Is the connection of Correct the connection of communication cable normal? communication cable. Exchange the outdoor unit PCB. 12-14 Samsung Electronics...
Exchange the compressor. compressor (u↔v, v↔w, w↔u) normal? Is the compressor body and Exchange the compressor. interphase resistance insulated? Is the connection cable for the Correct the cable connection. compressor and power terminal normal? Exchange the PCB. Samsung Electronics 12-15...
Exchange the compressor. compressor (u↔v, v↔w, w↔u) normal? Is the compressor body and Exchange the compressor. interphase resistance insulated? Is the connection cable for the Correct the cable connection. compressor and power terminal normal? Exchange the PCB. 12-16 Samsung Electronics...
Page 90
Is the resistance for the Exchange the PCB. detection of DC Link voltage normal? Is the resistance value of Exchange the PCB. DC Link discharge normal? Is the reactor insulation damaged? Exchange the PCB. Exchange the reactor. Samsung Electronics 12-17...
Page 91
Troubleshooting 12-2-16 The others 1. Capacity miss match – Check again the indoor unit option code. 12-18 Samsung Electronics...
FAN operation checking 1) Is the FAN motor running? • Controller trouble inside of the fan motor Press the ON/OFF button. 2) Is the connection of CN73 normal? • connector trouble of CN73 1. FAN Speed[HIGH] 2. FAN mode Samsung Electronics 12-19...
1) Is CN01 1, 3 over 250V? • Outdoor PCB Error 2) Is CN01 3, 5 within 1V~5V? • BLDC Motor Error 3) Is the voltage of CN01 6 changed? 4) Is the resistance of BLDC Motor 1, 3 opened after power off? 12-20 Samsung Electronics...
∞, 0Ω . . . Open or Short Stepping Motor Measure the resistance between the red wire and each terminal wire with a tester. Normal About 300Ω at the normal temperature (20˚C ~ 30˚C) Abnormal ∞, 0Ω . . . Open or Short Samsung Electronics 12-21...
• 4 WAY CONTROL SIGNAL COMPRESSOR • PFC CONTROL SIGNAL • COMPRESSOR CONTROL(6P, BLDC) • LED CONTROL SIGNAL • INDOOR COMMUNICATION SIGNAL • 4 WAY VALVE SMPS • EEV INDOOR UNIT PFC CIRCUIT DC5V AC INPUT DC12V DC15V AC300V AC230V DC25V Samsung Electronics 13-2...
It occurs when the drain pump is plugged out or it is out of order. Check the power of the drain pump and the position of the drain hose, and when the pump is faulty, contact the drain pump manufacturer. Samsung Electronics do not manufacture drain pumps.
Page 101
Also, the remote controller may not work under intensive light from a 3-wave length lamp or a neon sign due to the EMI. In this case, take the remote controller closer to the receiver. 14-5 Samsung Electronics...
Page 102
There is a cost table. But, our service engineer needs to visit to total up the cost correctly. When you move in, make sure to contact Samsung Electronics Service Center or Authorized Service Agent in advance to streamline the process.
5. When you have finished, insert the filter into the unit. 6. Clean the outdoor unit with a vacuum cleaner or a brush once a month. Note : • After cleaning the air conditioner, press the Filter Reset button. Wireless Remote Controller Wired Remote Controller 14-7 Samsung Electronics...
Electric and earth work shall meet the "Electric Facility Technology Standard" and the "Internal Wire Regulation" of the Electric Business Laws. Inspection & Trial Run Upon completion of the tests, you shall make a trial run while you explain the main functions of the air conditioner to finish the installation. Samsung Electronics 14-8...
183kgf . cm with a torque wrench. 7) Check for gas leakage. - At this time, especially check for gas leakage from the 3 way valve’s stem nuts, and from the service port cap. Samsung Electronics...
• Make sure you do not bend the connection pipes in the middle and store together with the cables. • Move the indoor and outdoor units to a new location. • Remove the mounting plate for the indoor unit and move it to a new location. Samsung Electronics 14-10...