Connecting Audio Components - Marantz SR3053 User Manual

CONNECTING SPEAKER WIRE
1.
Strip away approx. 10 mm (3/8 inch) of wire
insulation.
2.
Twist the bared wire ends tight, to prevent
short circuits.
3.
Loosen the knob by turning it counterclockwise.
4.
Insert the bare part of the wire into the hole
in side of each terminal.
5.
Tighten the knob by turning it clockwise to
secure the wire.
1. 2.
10 mm
(3/8 inch)
3. 4. 5.

CONNECTING AUDIO COMPONENTS

CD Player
Analog Audio
OUT
L
R
Digital Audio (optical)
L R
R L
VIDEO VIDEO
GND GND
VCR VCR DVD DVD BLU-RAY BLU-RAY
Ω ) )
FM( ( 75 FM 75Ω
AM AM
L L L L
ANTENNA ANTENNA
R R R R
CD / / TAPE CD CD / / TAPE CD TAPE TAPE VCR VCR DVD DVD BLU-RAY BLU-RAY
IN IN IN IN OUT OUT IN IN OUT OUT IN IN IN IN
ANALOG AUDIO ANALOG AUDIO ANALOG AUDIO ANALOG AUDIO
DVD DVD MONITOR OUT MONITOR OUT BLU-RAY BLU-RAY
L L SL SL C C SUB SUB
WOOFER WOOFER
R R L L
R R SR SR SW SW SURROUND SURROUND CENTER CENTER
SPEAKER SYSTEMS : 6-8 OHMS SPEAKER SYSTEMS : 6-8 OHMS
5.1CH INPUT 5.1CH INPUT PRE OUT PRE OUT
When using a tape deck, connect Analog Audio OUT/IN only.
Notes
• Do not connect this unit and other components to mains power until all connections between components have
been completed.
• Insert all plugs and connectors securely. Incomplete connections may make noise.
• Be sure to connect the left and right channels properly.
Red connectors are for the R (right) channel, and white connectors are for the L (left) channel.
• Be sure to connect input and output properly.
• Refer to the instructions for each component that is connected to this unit.
• Do not tie the connected cable into a bundle with the power supply cord or speaker cables. Doing so may cause
noise.
DIGITAL
OUTPUT
Y Y
COAXIAL COAXIAL
DVD DVD
OPTICAL OPTICAL P P
B B
IN IN
C C
B B
P P R R
OUT OUT
C C R R
MONITOR MONITOR CD CD CD CD BLU-RAY BLU-RAY DVD DVD BLU-RAY BLU-RAY MONITOR MONITOR
OUT OUT OPTICAL OPTICAL OUT OUT
REMOTE REMOTE
DIGITAL AUDIO IN DIGITAL AUDIO IN DIGITAL AUDIO IN DIGITAL AUDIO IN COMPONENT VIDEO COMPONENT VIDEO CONTROL CONTROL
MODEL NO. SR3053 MODEL NO. SR3053
AC IN AC IN
R R L L
FRONT FRONT
BASIC CONNECTIONS
CONNECTING DIGITAL AUDIO
COMPONENTS
• There are 3 digital inputs, 2 coaxial jacks and
1 optical jacks, on the rear panel. You can use
these jacks to input PCM, Dolby Digital and DTS
bitstream signals from a Blu-ray, DVD, and CD.
• Refer to the instructions for each component. To
setup the digital audio format of Blu-ray player, or
other digital source's connected to digital input
jacks.
• Use fi ber optical cables (optical) for CD, input
jacks. Use 75 ohms coaxial cables (for digital
audio) for Blu-ray, DVD, input jacks.
Notes
• There is no Dolby Digital RF input jack. Please
use an external RF demodulator Dolby Digital
decoder when connecting the Dolby Digital RF
output jack of the video disc player to the digital
input jack.
• The digital signal jacks on this unit conform to
the EIA standard. If you use a cable that does
not conform to this standard, this unit may not
function properly.
• Each type of audio jack works independently.
Signals input through the digital and analog jacks
are output through the corresponding digital and
analog jacks, respectively.
9