Table of Contents
Advertisement
Changing the unit's settings
■ Auto Tuning
You can restart auto channel setting if set up (➡ 18) fails for some
reason.
1 Press [ e , r ] to select "Auto Tuning" and press [OK].
When the confi rmation screen appears
2 Press [ w , q ] to select "Yes" and press [OK].
Tuning will start automatically.
When restarting the auto tuning using the main unit's buttons
(➡ 114, To reset this unit)
■ Download from TV
You can use "Download from TV" when you connect the unit to a
VIERA Link (HDAVI Control 3 or later) compatible TV with an HDMI
cable.
1 Press [ e , r ] to select "Download from TV" and press [OK].
When the confi rmation screen appears
2 Press [ w , q ] to select "Yes" and press [OK].
■ DVB Manual Tuning
You can set channels manually when the Auto Tuning could not
complete successfully.
1 Press [ e , r ] to select "DVB Manual Tuning" and press [OK].
DVB Manual Tuning
Physical Channel
[CH21]
Signal Quality
0
0
Signal Strength
Type
No.
Channel Name
Free TV: 0
Pay TV: 0
Radio: 0
Data: 0
Searching
Select physical channel
Start tuning
Select offset
RETURN
2 Press [ e , r ] to select the channel you want to set.
3 Press [ w , q ] to adjust the frequency.
The frequency rises and falls at equal intervals.
Adjust the frequency by checking the signal strength and signal
quality displays.
[Refer to "DVB Signal Condition" (➡ right) for signal quality and
signal strength.]
4 Press [OK] to start scan.
The set channel is displayed in the table.
5 Press [EXIT] and press [ 1 2 CH] to check that applicable
channels have been selected.
■ Add New DVB Channels
You can search for newly added terrestrial digital channels to
receive.
1 Press [ e , r ] to select "Add New DVB Channels" and press [OK].
The unit starts searching for newly available terrestrial digital
channels. This takes about 3 minutes.
Add New DVB Channels
Scan
21
This will take about 3 minutes.
CH
Channel Name
Type
Free TV: 0
Pay TV: 0
Radio: 0
Data: 0
Searching
RETURN
A message is displayed when the search is fi nished.
"No new channels found" is displayed when no new services can
be found.
2 Press [OK] to save the newly found channels.
RQT9433
86
177.50
MHz
1
0
1
0
New
6
9
Quality
■ DVB Signal Condition
You can check the quality and strength of digital broadcast signals.
Realign the aerial if you are receiving a poor signal.
When "DVB Signal Condition" is displayed in grey and cannot be
selected:
1 Press [EXIT] to exit the screen.
2 Press [INPUT SELECT] to select "TV".
3 Display the Setup menu again (➡ 85).
Press [ e , r ] to select "DVB Signal Condition" and press [OK].
The quality and strength of the signal are shown.
Press [ 1 2 CH] to select the channel.
Signal Quality
0
10
0
10
Signal Strength
Chan.Up
RETURN
Chan.Down
Signal Quality
Below 2 (display red):
The signal quality is so poor that there may be interference in the
pictures and sound.
2–5 (display orange):
The signal quality is basically adequate, but brief interference in the
pictures and sound is possible in isolated case.
Over 5 (display green):
Optimum picture and sound quality.
Signal Strength
The display for signal strength is grey. "0" means signal strength 0%,
"10" means signal strength 100%.
If the signal is too strong, the display will change from grey to red.
Reduce the signal amplifi cation at your aerial.
When the signal is weak:
– adjust the position and direction of the aerial.
– adjust the aerial reception with "DVB Manual Tuning" in the
Setup menu (➡ left).
– check that the current digital broadcast channel is correctly
broadcasting.
■ DVB Preferred Language
1 Press [ e , r ] to select "DVB Preferred Language" and press [OK].
2 Press [ e , r ] to select the item.
3 Press [ e , r ] to select the language.
You can select up to 6 different subtitles and audio tracks to be used
when multi audio and subtitles are received. Select the language.
If the selected language is not available, then the original language
will be selected.
Multi Audio
[English]
[Maori]
[Italian]
[Spanish]
Subtitles
[English]
[Maori]
[Italian]
[Spanish]
■ New Channel Message
When a new DVB channel is added, this unit will be informed
automatically. Then the confi rmation message appears. If you press
[OK], Auto Tuning starts.
1 Press [ e , r ] to select "New Channel Message".
2 Press [ w , q ] to select "Automatic" or "Off".
[Automatic]
[Off]
The channel messages are not shown.
(All factory default settings are indicated with underlined text.)
[French]
[German]
[French]
[German]
Hide quick links:
Advertisement
Table of Contents
