Assigning The Function Of Pedals And External Controllers; (Assign); Enabling Assignments 1-8 (Assign Switch); Specifying The Assignment Target (Assign Target) - Boss RC-300 Loop Station Owner's Manual

Assigning the Function of Pedals and External Controllers (Assign)
For each phrase memory, you can assign the function of the RC-300's pedals and any connected external pedals (EXP
pedals, foot switches: p . 24) . You can also make assignments for control change messages received from an external MIDI
device (e .g ., FC-300) .
For each phrase memory, you can create eight diff erent assignments (assignment numbers 1–8), which specify the
parameter controlled by each controller .
Parameter
Assign1 Switch
Assign1 Target
EFFECT CONTROL
Assign1 TargetMin
Assign1 TargetMax
Assign1 Source
EXP1 PEDAL
Value Explanation
Enabling Assignments 1–8 ( Assign Switch)
ON
Here you can specify whether assignments will be used .
OFF The assignment will not be used .
ON The assignment will be used .
Specifying the Assignment Target ( Assign Target)
Here you can choose the Assignment Target . In addition to the following assignment targets, you can also specify
a track, rhythm, or a LOOP FX parameter as the assignment target . For details on the parameters, refer to the
explanation of each parameter in this manual .
* Some parameters cannot be controlled during performance .
By pressing the pedal several times in succession, the phrase memory tempo can be set so
MEM Tempo(TAP)
it matches the timing you've used when pressing the pedal .
EFFECT CONTROL Applies an eff ect suitable for the selected LOOP FX type .
MEMORY INC
Switches the phrase memory .
MEMORY DEC
LOOP FX ON/OFF Switches the LOOP FX on/off .
FX TYPE INC
Switches the LOOP FX type .
FX TYPE DEC
UNDO/REDO Allows you to undo/redo the last recording or overdubbing of a track (p . 12) .
TR1–3 UNDO/REDO Allows you to undo/redo a specifi c track (p . 12) .
TR1–3 PLAY/STOP Allows you to play/stop a specifi c track .
ALL PLAY/STOP Allows you to simultaneously play/stop all tracks .
TRACK1–3 CLEAR Clears the track (p . 12) .
INPUT MASTER LEV Adjusts the input level from the INPUT (AUX, INST, MIC) jacks .
INPUT MIC SWITCH Switches the INPUT MIC jack input on/off .
CC#1–#31, CC#64–#95 Transmits the control change message specifi ed here from the MIDI OUT connector .
Specifying the Target Range ( Target Range)
0
Here you can specify the range in which the parameter can be controlled . The value will depend on the parameter
that's assigned as the Target (Assign Target) .
100
Specifying the Controller ( Assign Source)
Here you can specify the controller (source) that will control the target .
EXP1 PEDAL The RC-300's [EXP 1] pedal
The RC-300's [LOOP FX] pedal
* The [LOOP FX] pedal switches the LOOP FX on/off . If you don't want to use the [LOOP
LOOP FX PEDAL
FX] pedal to switch the LOOP FX on/off , choose "ASSIGN" as the setting of "Specifying the
Operation of the [LOOP FX] Pedal" (p . 32) .
CTL1–4 PEDAL A foot switch 1–4 connected to the CTL/EXP jacks (p . 24)
EXP2–3 PEDAL An EXP pedal 2–3 connected to the CTL/EXP jacks (p . 24)
TRACK1–3 REC/DUB The beginning of recording/overdubbing triggered by the track 1–3 [REC/DUB/PLAY] pedal
TRACK1–3 PLAY The beginning of playback triggered by the track 1–3 [REC/DUB/PLAY] pedal
SYNC START/STOP ALL START/STOP messages from the master RC-300 unit (p . 39) .
CC#1–#31, CC#64–#95 Control change messages (1–31, 64–95) from an external MIDI device
Phrase Memory Settings
23