Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Remcor TJ150
Summary of Contents for Remcor TJ150
- Page 1 ICE/DISPENSERS MODELS: TJ150 TJ150-B Operator’ s Manual Part No. 90985 February, 1997 Revision B THIS DOCUMENT CONTAINS IMPORTANT INFORMATION This Manual must be read and understood before installing or operating this equipment â REMCOR INC: PRINTED IN U.S.A...
-
Page 2: Table Of Contents
........FIGURE 5. WIRING DIAGRAM TJ150 DISPENSER . -
Page 3: Safety Precautions
GENERAL DESCRIPTION The Remcor “ TJ”series of ice dispensers solve your ice service needs the sanitary, space saving, economical way. Designed to be manually filled with ice from any remote ice making source, or automatically filled from a top-mounted “... -
Page 4: Ice Maker
ICE MAKER REMCOR “ K”model ice/beverage dispensers are designed to be used with one of several top-mounted “ ice cubers.”These cubers must be obtained from the appropriate manufacturer or distributor in your area. The following ice makers are approved for use on the TJ150 “ K”models:... -
Page 5: Installation Instructions
Figure 4 provides a mounting template for mounting the dispenser to a counter, if so desired. Follow the instructions for “ K”models for sealing the unit to the counter. MODEL TJ150 “K” The ice dispenser must be sealed to the counter (see template drawing Figure 4). Locate the desired position for the dispenser, then mark the outline dimensions on the counter using the template drawings. -
Page 6: Figure 1. Specification Drawing Tj150
27 5/8 15 1/4 34 15/32 32 7/8 11 11/32 17 5/8 FIGURE 1. SPECIFICATION DRAWING TJ150 POSITION ICE MAKER ON DISPENSER- TO COVER OPENING INTO STORAGE HOPPER. APPLY RTV AROUND INSIDE OF ICE MAKER OUTLINE ON DISPENSER COVER TO FORM A SEAL. -
Page 7: Cleaning Instructions
CLEANING INSTRUCTIONS WARNING: DISCONNECT POWER BEFORE CLEANING! Do not use metal scrapers, sharp objects or abrasives on the ice storage hopper, top cover and the agitator disk, as damage may result. Do not use solvents or other cleaning agents, as they may attack the plastic material. -
Page 8: Maintenance
MAINTENANCE The following dispenser maintenance should be performed at the intervals indicated: DAILY or as required Remove foreign material from the vending area sink to prevent drain blockage. WEEKLY or as required Clean vending area. Check for proper water drainage from the vending area sink. MONTHLY Clean and sanitize the hopper interior (see CLEANING INSTRUCTIONS). -
Page 9: Gate Restrictor Plate
GATE RESTRICTOR PLATE CAUTION: Disconnect power to dispenser before installing, removing or adjusting restrictor. INSTALL PLATE ON STUDS AS SHOWN FIGURE 3. GATE RESTRICTOR PLATE ADJUSTMENT This dispenser is provided with a gate restrictor plate installed in its highest position. This plate adjusts the rate of ice flow from the dispenser. -
Page 10: Troubleshooting Guide
TROUBLESHOOTING GUIDE Should your unit fail to operate properly, check that there is power to the unit and that the hopper contains ice. If the unit does not dispense, check the following chart under the appropriate symptoms to aid in locating the defect. -
Page 11: Figure 4. Mounting Template
1 1/8 18 1/2 3/8 DIA. (4) 1 1/8 27 3/4 FIGURE 4. MOUNTING TEMPLATE 90985... -
Page 12: Figure 5. Wiring Diagram Tj150 Dispenser
CONTROL SWITCH OPTION DISPENSE SWITCH TERMINAL BOARD SERVICE INFORMATION ELECTRIC SHOCK HAZARD. DISCONNECT DANGER! POWER BEFORE SERVICING UNIT. SOLENOID ADJUSTMENT WHEN REPLACING SOLENOID ADJUST TO 7/8 INCH AS SHOWN BEFORE TIGHTENING MOUNTING SCREWS FIGURE 5. WIRING DIAGRAM TJ150 DISPENSER 90985... -
Page 13: Figure 6. Wiring Diagram Tj150-K Disenser
CONTROL SWITCH OPTION DISPENSE SWITCH TERMI- BOARD SERVICE INFORMATION ELECTRIC SHOCK HAZARD. DISCONNECT POWER DANGER! BEFORE SERVICING UNIT. SOLENOID ADJUSTMENT WHEN REPLACING SOLENOID ADJUST TO 7/8 INCH AS SHOWN BEFORE TIGHTENING MOUNTING SCREWS FIGURE 6. WIRING DIAGRAM TJ150-K DISENSER 90985... -
Page 14: Figure 7. Final Assembly
FIGURE 7. FINAL ASSEMBLY 90985... -
Page 15: Final Assembly Parts List
FINAL ASSEMBLY PARTS LIST Item No. Part No. Description 21491 Gate Slide 23062 Foam Shield 21515 Depressor Lever 24069 Agitator 30895 Dispense Switch 31007 Switch Boot 31163 Switch Insert 31091 Transformer 31889 Agitator Motor 50454 Motor Shaft Seal 50806 Motor Gasket 51432 24200 Lid (K Models) -
Page 16: Figure 8. Solenoid Assembly
FIGURE 8. SOLENOID ASSEMBLY -- EXPLODED VIEW & PARTS LIST Index Part No. Quantity Description 21493 Solenoid Mounting Plate 31551 Solenoid Service Kit 70171 8--32 x 3/8 Phil Tr HD Screw 70121 No. 8 Lockwasher 50752 Isolator 50789 Bumper Assembly 70423 Cotter Pin 10080... -
Page 17: Warranty
For a copy of the warranty applicable to your Cornelius and or Remcor product, in your country, please write, fax or telephone the IMI Cornelius office near- est you. Please provide the equipment model number, serial number and the date of purchase. - Page 18 CORPORATE HEADQUARTERS: Remcor Incorporated 500 Regency Drive Glendale Heights, IL 60139 708. 980.6900...