Table of Contents
Advertisement
1. Start mowing the edge of the lawn nearest to the
power point so the cable is laid out on the lawn you
have already cut.
2. Mow twice a week during the growing season, your lawn
will suffer if more than a third of its length is cut at one
time and this may also result in poor collection.
Do Not Overload Your Mower
Mowing long thick grass may cause the motor speed to
K
L
fan
M
grassbox
is empty
N
P
Adjusting the Cutting Height
Removing and fitting the Blade and Fan
blade bolt
blade
spacers
Grassbox Instructions
grassbox is full
Remove bag
Lift out box
How to Mow
drop, you will hear a change in the motor sound. If the
motor speed drops you may overload your lawnmower
which may cause damage. When mowing in long thick
grass a first cut with the cutting height set higher will help
reduce the load. See Adjusting the Cutting Height.
REMEMBER: For best grass collection always mow in a
straight line, do not swing the lawnmower from side to side.
Always handle the blade with care - sharp edges
could cause injury. USE GLOVES. Never use more
than 3 Cutting Height Spacers. Spacers must only
be fitted between the blade and the fan and NEVER
between the blade and the bolt.
1. Remove the blade bolt, and blade as described in
Removing the Blade and Fan.
2. For a Lower Cut - Add spacers to a maximum of 3.
3. For a Higher Cut - Take spacers away.
4. Refit the blade as described in Fitting the Blade and Fan.
Removing the Blade and Fan
1. To remove the blade bolt, hold the fan firmly and with
the spanner provided loosen the blade bolt by turning
it anti-clockwise (K).
2. Remove the blade bolt, blade, spacers and fan. (L)
3. Inspect for damage and clean as necessary.
•
Renew your metal blade after 50 hours mowing or 2
years whichever is the sooner - regardless of condition.
•
If the blade is cracked or damaged replace it with
a new one.
•
Never use a blade bolt if the insulated head is
damaged cracked or missing.
Fitting the Blade and Fan
1. Ensure the fan is located correctly.(L)
2. Place the spacers onto the fan ensuring the pegs
have located into the holes.(L)
3. Place the blade onto the spacers ensuring the pegs have
located into the holes on the blade and ensuring the
blades is positioned as illustrated in Figure L.
4. Place the blade bolt through the centre hole of the blade.
5. Tighten down clockwise by hand.
6. Hold the fan firmly and tighten the blade bolt with the
spanner provided.
Using the product with the bag:
The bag with its grass can be disposed of with green
waste and is fully compostable. This means easy, clean dis-
posal of grass. Do not leave bag in grassbox after use. Do not
use for any other purpose than grass collecting. For replace-
ment bags or for more information contact our helpline
on 01325 300303 or visit our website: www.flymo.com.
Alternatively the product can be used without the
bag, grass will collect in the box.
Grassbox Full Indicator (M)
•
IMPORTANT The machine must be switched on
for the grassbox full indicator to operate.
1. When the ball reaches the top of the indicator win-
dow, it is time to empty the grassbox.
2. When the ball is NOT visible in the indicator window,
grass is being collected.
Emptying the Grass
•
Stop the lawnmower, and wait until the blade has
stopped rotating BEFORE lifting the grassbox lid.
WITH BAG (N)
1. Lift grassbox lid.
2. Remove bag. Insert new bag if continuing to cut grass.
3. Close grassbox lid carefully.
WITHOUT BAG (P)
1. Lift grassbox lid.
2. Lift out grassbox and empty.
3. Replace grassbox and close lid carefully.
•
Failure to fit the grassbox and grassbox lid correctly
will cause poor grass collection. Ensure there is no
grass trapped between the lid and the hood.
Advertisement
Table of Contents
